Op 09-08-17 om 08:46 schreef Shashank Sharma:
> To pass AVI infoframes from display controller to LSPCON, we
> have to write infoframe packets into vendor specified AUX address,
> in vendor specified way.
>
> Also, LSPCON vendors provide AUX offsets, to inform the LSPCON
> chip that the AVI IF packets are written, so that the firmware
> can pick it up and apply.
>
> This patch adds function to write AVI infoframes for both MCA as
> well as Parade Tech LSPCON chips. These two vendors provide different
> methods for writing infoframes, so this patch contains two different
> functions, one for each.
>
> V2: Rebase
>
> Cc: Ville Syrjälä <[email protected]>
> Cc: Imre Deak <[email protected]>
> Signed-off-by: Shashank Sharma <[email protected]>
> ---
This patch will fail to compile without 7/7 applied:
- enc_to_intel_lspcon missing.
- crtc_state->lspcon_active missing.
> drivers/gpu/drm/i915/intel_ddi.c | 12 +-
> drivers/gpu/drm/i915/intel_drv.h | 16 +++
> drivers/gpu/drm/i915/intel_hdmi.c | 15 ++-
> drivers/gpu/drm/i915/intel_lspcon.c | 246
> ++++++++++++++++++++++++++++++++++++
> 4 files changed, 284 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/intel_ddi.c
> b/drivers/gpu/drm/i915/intel_ddi.c
> index 9384080..08f3567 100644
> --- a/drivers/gpu/drm/i915/intel_ddi.c
> +++ b/drivers/gpu/drm/i915/intel_ddi.c
> @@ -2193,6 +2193,15 @@ static void intel_ddi_pre_enable(struct intel_encoder
> *encoder,
> pipe_config->shared_dpll,
> intel_crtc_has_type(pipe_config,
>
> INTEL_OUTPUT_DP_MST));
> +
> + if (pipe_config->lspcon_active) {
> + struct intel_digital_port *dig_port =
> + enc_to_dig_port(&encoder->base);
> +
> + dig_port->set_infoframes(&encoder->base,
> + pipe_config->has_infoframe,
> + pipe_config, conn_state);
> + }
> }
> if (type == INTEL_OUTPUT_HDMI) {
> intel_ddi_pre_enable_hdmi(encoder,
> @@ -2734,8 +2743,6 @@ void intel_ddi_init(struct drm_i915_private *dev_priv,
> enum port port)
> intel_encoder->crtc_mask = (1 << 0) | (1 << 1) | (1 << 2);
> intel_encoder->cloneable = 0;
>
> - intel_infoframe_init(intel_dig_port);
> -
> if (init_dp) {
> if (!intel_ddi_init_dp_connector(intel_dig_port))
> goto err;
> @@ -2765,6 +2772,7 @@ void intel_ddi_init(struct drm_i915_private *dev_priv,
> enum port port)
> port_name(port));
> }
>
> + intel_infoframe_init(intel_dig_port);
> return;
>
> err:
> diff --git a/drivers/gpu/drm/i915/intel_drv.h
> b/drivers/gpu/drm/i915/intel_drv.h
> index adab635..99eaab6 100644
> --- a/drivers/gpu/drm/i915/intel_drv.h
> +++ b/drivers/gpu/drm/i915/intel_drv.h
> @@ -1052,6 +1052,10 @@ struct intel_lspcon {
> bool active;
> enum drm_lspcon_mode mode;
> enum lspcon_vendor vendor;
> +
> + void (*write_infoframe)(struct drm_encoder *encoder,
> + const struct intel_crtc_state *crtc_state,
> + union hdmi_infoframe *frame);
> };
>
> struct intel_digital_port {
> @@ -1978,6 +1982,18 @@ void intel_color_load_luts(struct drm_crtc_state
> *crtc_state);
> bool lspcon_init(struct intel_digital_port *intel_dig_port);
> void lspcon_resume(struct intel_lspcon *lspcon);
> void lspcon_wait_pcon_mode(struct intel_lspcon *lspcon);
> +bool lspcon_ycbcr420_config(struct drm_connector *connector,
> + struct intel_crtc_state *config);
> +void lspcon_write_infoframe(struct drm_encoder *encoder,
> + const struct intel_crtc_state *crtc_state,
> + enum hdmi_infoframe_type type,
> + const void *buf, ssize_t len);
> +void lspcon_set_infoframes(struct drm_encoder *encoder,
> + bool enable,
> + const struct intel_crtc_state *crtc_state,
> + const struct drm_connector_state *conn_state);
> +bool lspcon_infoframe_enabled(struct drm_encoder *encoder,
> + const struct intel_crtc_state *pipe_config);
>
> /* intel_pipe_crc.c */
> int intel_pipe_crc_create(struct drm_minor *minor);
> diff --git a/drivers/gpu/drm/i915/intel_hdmi.c
> b/drivers/gpu/drm/i915/intel_hdmi.c
> index e4a27e1..5710029 100644
> --- a/drivers/gpu/drm/i915/intel_hdmi.c
> +++ b/drivers/gpu/drm/i915/intel_hdmi.c
> @@ -1909,9 +1909,18 @@ void intel_infoframe_init(struct intel_digital_port
> *intel_dig_port)
> intel_dig_port->set_infoframes = g4x_set_infoframes;
> intel_dig_port->infoframe_enabled = g4x_infoframe_enabled;
> } else if (HAS_DDI(dev_priv)) {
> - intel_dig_port->write_infoframe = hsw_write_infoframe;
> - intel_dig_port->set_infoframes = hsw_set_infoframes;
> - intel_dig_port->infoframe_enabled = hsw_infoframe_enabled;
> + if (intel_dig_port->lspcon.active) {
> + intel_dig_port->write_infoframe =
> + lspcon_write_infoframe;
> + intel_dig_port->set_infoframes = lspcon_set_infoframes;
> + intel_dig_port->infoframe_enabled =
> + lspcon_infoframe_enabled;
> + } else {
> + intel_dig_port->set_infoframes = hsw_set_infoframes;
> + intel_dig_port->infoframe_enabled =
> + hsw_infoframe_enabled;
> + intel_dig_port->write_infoframe = hsw_write_infoframe;
> + }
> } else if (HAS_PCH_IBX(dev_priv)) {
> intel_dig_port->write_infoframe = ibx_write_infoframe;
> intel_dig_port->set_infoframes = ibx_set_infoframes;
> diff --git a/drivers/gpu/drm/i915/intel_lspcon.c
> b/drivers/gpu/drm/i915/intel_lspcon.c
> index 93507c5..b4fcd30 100644
> --- a/drivers/gpu/drm/i915/intel_lspcon.c
> +++ b/drivers/gpu/drm/i915/intel_lspcon.c
> @@ -31,6 +31,18 @@
> #define LSPCON_VENDOR_PARADE_OUI 0x001CF8
> #define LSPCON_VENDOR_MCA_OUI 0x0060AD
>
> +/* AUX addresses to write AVI IF into */
> +#define LSPCON_MCA_AVI_IF_WRITE_OFFSET 0x5C0
> +#define LSPCON_MCA_AVI_IF_CTRL 0x5DF
> +#define LSPCON_MCA_AVI_IF_KICKOFF (1 << 0)
> +#define LSPCON_MCA_AVI_IF_HANDLED (1 << 1)
> +
> +#define LSPCON_PARADE_AVI_IF_WRITE_OFFSET 0x516
> +#define LSPCON_PARADE_AVI_IF_CTRL 0x51E
> +#define LSPCON_PARADE_AVI_IF_KICKOFF (1 << 7)
> +#define LSPCON_PARADE_AVI_IF_STATUS 0x51F
> +#define LSPCON_PARADE_AVI_IF_HANDLED (2 << 6)
> +
> static struct intel_dp *lspcon_to_intel_dp(struct intel_lspcon *lspcon)
> {
> struct intel_digital_port *dig_port =
> @@ -227,6 +239,240 @@ static void lspcon_resume_in_pcon_wa(struct
> intel_lspcon *lspcon)
> DRM_DEBUG_KMS("LSPCON DP descriptor mismatch after resume\n");
> }
>
> +bool lspcon_ycbcr420_config(struct drm_connector *connector,
> + struct intel_crtc_state *config)
> +{
> + struct drm_display_info *info = &connector->display_info;
> + struct drm_display_mode *mode = &config->base.adjusted_mode;
> +
> + if (drm_mode_is_420_only(info, mode)) {
> +
> + if (!connector->ycbcr_420_allowed) {
> + DRM_ERROR("Platform doesn't support YCBCR420 output\n");
> + return false;
> + }
> +
> + config->port_clock /= 2;
> + return true;
> + }
> +
> + return false;
> +}
> +
> +static bool _lspcon_write_avi_infoframe_parade(struct drm_dp_aux *aux,
> + const uint8_t *buffer,
> + ssize_t len)
> +{
> + u8 avi_if_ctrl;
> + u8 avi_if_status;
> + u8 count = 0;
> + u8 retry = 5;
> + u8 avi_buf[8] = {0, };
Initialize the first byte to 1, and you can remove the special case for count
== 0?
> + uint16_t reg;
> + ssize_t ret;
> +
> + while (count++ < 4) {
> +
> + do {
> + /* Is LSPCON FW ready */
> + reg = LSPCON_PARADE_AVI_IF_CTRL;
> + ret = drm_dp_dpcd_read(aux, reg, &avi_if_ctrl, 1);
> + if (ret < 0) {
> + DRM_ERROR("DPCD read failed, add:0x%x\n", reg);
> + return false;
> + }
> +
> + if (avi_if_ctrl & LSPCON_PARADE_AVI_IF_KICKOFF)
> + break;
> + usleep_range(100, 200);
> + } while (--retry);
> +
> + if (!(avi_if_ctrl & LSPCON_PARADE_AVI_IF_KICKOFF)) {
> + DRM_ERROR("LSPCON FW not ready for infoframes\n");
> + return false;
> + }
> +
> + /*
> + * AVI Infoframe contains 31 bytes of data:
> + * HB0 to HB2 (3 bytes header)
> + * PB0 to PB27 (28 bytes data)
> + * As per Parade spec, while sending first block (8bytes),
> + * byte 0 is kept for request token no, and byte1 - byte7
> + * contain frame data. So we have to pack frame like this:
> + * first block of 8 bytes: <token> <HB0-HB2> <PB0-PB3>
> + * next 3 blocks: <PB4-PB27>
> + */
> + if (count)
> + memcpy(avi_buf, buffer + count * 8 - 1, 8);
> + else {
> + avi_buf[0] = 1;
> + memcpy(&avi_buf[1], buffer, 7);
> + }
^This won't work, I think.
for (count = 0; count < 4; count++)
> +
> + /* Write 8 bytes of data at a time */
> + reg = LSPCON_PARADE_AVI_IF_WRITE_OFFSET;
> + ret = drm_dp_dpcd_write(aux, reg, avi_buf, 8);
> + if (ret < 0) {
> + DRM_ERROR("DPCD write failed, add:0x%x\n", reg);
> + return false;
> + }
> +
> + /*
> + * While sending a block of 8 byes, we need to inform block
> + * number to FW, by programming bits[1:0] of ctrl reg with
> + * block number
> + */
> + avi_if_ctrl = 0x80 + count;
> + reg = LSPCON_PARADE_AVI_IF_CTRL;
> + ret = drm_dp_dpcd_write(aux, reg, &avi_if_ctrl, 1);
> + if (ret < 0) {
> + DRM_ERROR("DPCD write failed, add:0x%x\n", reg);
> + return false;
> + }
> + }
> +
> + /* Check LSPCON FW status */
> + reg = LSPCON_PARADE_AVI_IF_STATUS;
> + ret = drm_dp_dpcd_read(aux, reg, &avi_if_status, 1);
> + if (ret < 0) {
> + DRM_ERROR("DPCD write failed, address 0x%x\n", reg);
> + return false;
> + }
> +
> + if (avi_if_status & LSPCON_PARADE_AVI_IF_HANDLED)
> + DRM_DEBUG_KMS("AVI IF handled by FW\n");
you should check for (avi_if_status & AVI_IF_STATUS_MASK) == IF_HANDLED,
afaict from specs, if the status completes with an error, you still report
success here.
> + return true;
> +}
> +
> +static bool _lspcon_write_avi_infoframe_mca(struct drm_dp_aux *aux,
> + const uint8_t *buffer, ssize_t len)
> +{
> + int ret;
> + uint32_t val = 0;
> + uint16_t reg;
> + const uint8_t *data = buffer;
> +
> + reg = LSPCON_MCA_AVI_IF_WRITE_OFFSET;
> + while (val < len) {
> + ret = drm_dp_dpcd_write(aux, reg, (void *)data, 1);
> + if (ret < 0) {
> + DRM_ERROR("DPCD write failed, add:0x%x\n", reg);
> + return false;
> + }
> + val++; reg++; data++;
> + }
> +
> + val = 0;
> + reg = LSPCON_MCA_AVI_IF_CTRL;
> + ret = drm_dp_dpcd_read(aux, reg, &val, 1);
> + if (ret < 0) {
> + DRM_ERROR("DPCD read failed, address 0x%x\n", reg);
> + return false;
> + }
> +
> + /* Indicate LSPCON chip about infoframe, clear bit 1 and set bit 0 */
> + val &= ~LSPCON_MCA_AVI_IF_HANDLED;
> + val |= LSPCON_MCA_AVI_IF_KICKOFF;
> +
> + ret = drm_dp_dpcd_write(aux, reg, &val, 1);
> + if (ret < 0) {
> + DRM_ERROR("DPCD read failed, address 0x%x\n", reg);
> + return false;
> + }
> +
> + val = 0;
> + ret = drm_dp_dpcd_read(aux, reg, &val, 1);
> + if (ret < 0) {
> + DRM_ERROR("DPCD read failed, address 0x%x\n", reg);
> + return false;
> + }
> +
> + if (val == LSPCON_MCA_AVI_IF_HANDLED)
> + DRM_DEBUG_KMS("AVI IF handled by FW\n");
> +
> + return true;
> +}
> +
> +void lspcon_write_infoframe(struct drm_encoder *encoder,
> + const struct intel_crtc_state *crtc_state,
> + enum hdmi_infoframe_type type,
> + const void *frame, ssize_t len)
> +{
> + bool ret;
> + struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
> + struct intel_lspcon *lspcon = enc_to_intel_lspcon(encoder);
> +
> + /* LSPCON only needs AVI IF */
> + if (type != HDMI_INFOFRAME_TYPE_AVI)
> + return;
> +
> + if (lspcon->vendor == LSPCON_VENDOR_MCA)
> + ret = _lspcon_write_avi_infoframe_mca(&intel_dp->aux,
> + frame, len);
> + else
> + ret = _lspcon_write_avi_infoframe_parade(&intel_dp->aux,
> + frame, len);
> +
> + if (!ret)
> + DRM_ERROR("Failed to write AVI infoframes\n");
Well, both infoframe write functions already report a DRM_ERROR, this print
could be lower or removed. :)
> + else
> + DRM_DEBUG_DRIVER("AVI infoframes updated successfully\n");
> +}
> +
> +void lspcon_set_infoframes(struct drm_encoder *encoder,
> + bool enable,
> + const struct intel_crtc_state *crtc_state,
> + const struct drm_connector_state *conn_state)
> +{
> + ssize_t ret;
> + union hdmi_infoframe frame;
> + uint8_t buf[VIDEO_DIP_DATA_SIZE];
> + struct intel_digital_port *dig_port = enc_to_dig_port(encoder);
> + struct intel_dp *intel_dp = &dig_port->dp;
> + struct drm_connector *connector = &intel_dp->attached_connector->base;
> + const struct drm_display_mode *mode = &crtc_state->base.adjusted_mode;
> + bool is_hdmi2_sink = connector->display_info.hdmi.scdc.supported;
> +
> + if (!crtc_state->lspcon_active) {
> + DRM_ERROR("Writing infoframes while LSPCON disabled ?\n");
> + return;
> + }
> +
> + ret = drm_hdmi_avi_infoframe_from_display_mode(&frame.avi,
> + mode, is_hdmi2_sink);
> + if (ret < 0) {
> + DRM_ERROR("couldn't fill AVI infoframe\n");
> + return;
> + }
> +
> + if (crtc_state->ycbcr420)
> + frame.avi.colorspace = HDMI_COLORSPACE_YUV420;
> + else
> + frame.avi.colorspace = HDMI_COLORSPACE_RGB;
> +
> + drm_hdmi_avi_infoframe_quant_range(&frame.avi, mode,
> + crtc_state->limited_color_range ?
> + HDMI_QUANTIZATION_RANGE_LIMITED :
> + HDMI_QUANTIZATION_RANGE_FULL,
> + false);
> +
> + ret = hdmi_infoframe_pack(&frame, buf, sizeof(buf));
> + if (ret < 0) {
> + DRM_ERROR("Failed to pack AVI IF\n");
In general, it would be nice if we also get the returned error code for
debugging. :)
> + return;
> + }
> +
> + dig_port->write_infoframe(encoder, crtc_state, HDMI_INFOFRAME_TYPE_AVI,
> + buf, ret);
> +}
> +
> +bool lspcon_infoframe_enabled(struct drm_encoder *encoder,
> + const struct intel_crtc_state *pipe_config)
> +{
> + return enc_to_intel_lspcon(encoder)->active;
> +}
> +
> void lspcon_resume(struct intel_lspcon *lspcon)
> {
> enum drm_lspcon_mode expected_mode;
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
