Randy,
Is there a list of hardware that supports PSMI ? We need this for ipmitool
and the Java version...
http://www.jblade.com:8080/products/retuli/ipmiCx/RetuliIpmiCxOverview.jsf
On Thu, Sep 22, 2011 at 1:45 PM, Schafer, Randy A <randy.a.scha...@intel.com
> wrote:
> If the SDR update did not see the power supplies, then the firmware
> probably cannot communicate with them using PMBus protocol.
> The SR1690WBR does not support PSMI power supplies. It only supports PMBus
> 1.1 power supplies.
>
> Regards,
>
> Randy Schafer
> EPSD Firmware Engineering
> Intel Corporation
> randy.a.scha...@intel.com
>
> -----Original Message-----
> From: S. H. Lee [mailto:smil...@korea.ac.kr]
> Sent: Wednesday, September 21, 2011 7:22 PM
> To: Schafer, Randy A
> Cc: 'ipmitool-devel'; 'Zdenek Styblik'
> Subject: RE: [Ipmitool-devel] measuring the power consumption of a server
>
> When I updated the SDR, I chose Intel SR1690WB since the actual model is
> SR1690WBR.
> SDR utility displayed a message for PS1 and PS2 as 'no power supply'.
> Therefore, I checked SSI power supply manually.
>
> Then, doesn't SR1690WBR support PSMI power supplies?
>
> If SR1690WBR supports PMBus 1.1 power supplies for power sensors, IPMItool
> may display the measured value for power sensors.
> But, on my server, IPMItool only displays output voltage values.
>
> Best regards,
>
>
> > -----Original Message-----
> > From: Schafer, Randy A [mailto:randy.a.scha...@intel.com]
> > Sent: Thursday, September 22, 2011 10:23 AM
> > To: S. H. Lee; 'Zdenek Styblik'
> > Cc: 'ipmitool-devel'
> > Subject: RE: [Ipmitool-devel] measuring the power consumption of a
> > server
> >
> > When you updated the SDR, which chassis did you specify?
> > Did the SDR utility display a message about PS1 and PS2 being present
> > or not?
> >
> > These servers do not support PSMI power supplies. They only support
> > PMBus
> > 1.1 power supplies for power sensors.
> >
> > Randy Schafer
> > EPSD Firmware Engineering
> > Intel Corporation
> > randy.a.scha...@intel.com
> >
> > -----Original Message-----
> > From: S. H. Lee [mailto:smil...@korea.ac.kr]
> > Sent: Wednesday, September 21, 2011 5:22 PM
> > To: 'Zdenek Styblik'
> > Cc: 'ipmitool-devel'
> > Subject: Re: [Ipmitool-devel] measuring the power consumption of a
> > server
> >
> > Hi,
> >
> > I've attempted some possible solutions.
> > - updating BMC firmware (ver.: 0.57)
> > - updating BIOS
> > - reinstall IPMItool (ver. 1.8.11)
> >
> > By any chance, may I need additional hardware connector for power supply?
> >
> > During BIOS&BMC firmware update, BMC didn't automatically detect any
> > power supply.
> > Thus, I manually checked 'yes' for 'SSI power supply'.
> > I also carried out a FRU/SDR package update.
> >
> > After these tries, BMC still recognizes a power supply.
> >
> >
> > > -----Original Message-----
> > > From: Zdenek Styblik [mailto:zdenek.styb...@gmail.com]
> > > Sent: Thursday, September 22, 2011 4:41 AM
> > > To: S. H. Lee
> > > Cc: ipmitool-devel
> > > Subject: Re: [Ipmitool-devel] measuring the power consumption of a
> > > server
> > >
> > > On Wed, Sep 21, 2011 at 2:56 PM, S. H. Lee <smil...@korea.ac.kr>
> wrote:
> > > > Thanks for your comments,
> > > >
> > > > In the last mail, I said that I have a SV7-2186. It isn't the
> > > > model I
> > > have.
> > > > My server is Intel SR1690WBR with a S5500WBV.
> > > > I've checked some manuals and mailing lists.
> > > >
> > > > The problem of my server is that IPMI cannot detect a power supply.
> > > >
> > > > BB +1.1V IOH | 1.084 | Volts | ok | na |
> 1.027
> > > > | 1.054 | 1.146 | 1.177 | na BB +1.1V P1 Vccp | 0.933
> > > > | Volts | ok | na | 0.683 | 0.708 | 1.501
> |
> > > > 1.543 | na BB +1.5V P1 DDR3 | 1.505 | Volts | ok |
> > > na
> > > > | 1.362 | 1.401 | 1.589 | 1.635 | na BB +1.8V AUX
> > > > | 1.781 | Volts | ok | na | 1.673 | 1.720
> > > > | 1.874 | 1.927 | na BB +3.3V | 3.296 | Volts
> > > > | ok | na | 2.982 | 3.067 | 3.525 | 3.625 |
> > > > na BB +3.3V STBY | 3.239 | Volts | ok | na |
> > > > 2.982 | 3.067 | 3.525 | 3.625 | na BB +5.0V |
> > > > 4.971 | Volts | ok | na | 4.471 | 4.630 |
> > > > 5.380 | 5.538 | na BB +5.0V STBY | 4.886 | Volts
> > > > | ok | na | 4.416 | 4.565 | 5.272 | 5.421 |
> > > > na BB +12.0V | 12.039 | Volts | ok | na |
> > > > 10.739 | 11.103 | 12.923 | 13.287 | na BB +1.35v P1 MEM |
> > > > na | Volts | na | na | 1.236 | 1.271 |
> > > > 1.443 | 1.484 | na Baseboard Temp | 27.000 | degrees C
> > > > | ok | na | 5.000 | 10.000 | 61.000 | 66.000 |
> > > > na Front Panel Temp | 26.000 | degrees C | ok | na |
> > > > 0.000 | 5.000 | 44.000 | 48.000 | na IOH Therm Margin |
> > > > -44.000 | degrees C | ok | na | na | na |
> > > > 5.000 | 10.000 | na Mem P1 Thrm Mrgn | -36.000 | degrees C
> > > > | ok | na | na | na | 5.000 | 10.000 |
> > > > na Processor 1 Fan | 7616.000 | RPM | ok | na |
> > > > 640.000 | 768.000 | na | na | na Processor 1A Fan |
> > > > 5440.000 | RPM | ok | na | 640.000 | 768.000 |
> > > > na | na | na Memory Fan 1 | 5184.000 | RPM
> > > > | ok | na | 640.000 | 768.000 | na | na |
> > > > na Memory Fan 1R | 7616.000 | RPM | ok | na |
> > > > 640.000 | 768.000 | na | na | na Processor 2 Fan |
> > > > 7424.000 | RPM | ok | na | 640.000 | 768.000 |
> > > > na | na | na Processor 2A Fan | 5056.000 | RPM
> > > > | ok | na | 640.000 | 768.000 | na | na |
> > > > na Memory Fan 2 | 7616.000 | RPM | ok | na |
> > > > 640.000 | 768.000 | na | na | na Memory Fan 2R |
> > > > 5824.000 | RPM | ok | na | 640.000 | 768.000 |
> > > > na | na | na
> > > > P1 Therm Margin | -56.000 | degrees C | ok | na | na
> > > > | na | na | na | na
> > > > P1 Therm Ctrl % | 0.000 | unspecified | ok | na |
> > > na
> > > > | na | 11.700 | 19.500 | na Pwr Unit Status | 0x0
> > > > | discrete | 0x0000| na | na | na | na
> |
> > > > na | na IPMI Watchdog | 0x0 | discrete | 0x0000|
> > > na
> > > > | na | na | na | na | na Physical Scrty
> > > > | 0x0 | discrete | 0x0000| na | na | na
> > > > | na | na | na SMI Timeout | 0x0 | discrete
> > > > | 0x0000| na | na | na | na | na |
> > > > na System Event Log | 0x0 | discrete | 0x0000| na |
> > > na
> > > > | na | na | na | na System Event | 0x0
> > > > | discrete | 0x0000| na | na | na | na
> |
> > > > na | na
> > > > P1 Status | 0x0 | discrete | 0x8000| na | na
> > > > | na | na | na | na
> > > > P1 VRD Hot | 0x0 | discrete | 0x0000| na | na
> > > > | na | na | na | na CATERR | 0x0
> > > > | discrete | 0x0000| na | na | na | na
> |
> > > > na | na CPU Missing | 0x0 | discrete | 0x0000|
> > > na
> > > > | na | na | na | na | na IOH Therm Trip
> > > > | 0x0 | discrete | 0x0000| na | na | na
> > > > | na | na | na NM Capabilities | na | discrete
> > > > | na | na | na | na | na | na |
> > > > na
> > > >
> > > > As you can see above, 'Pwr Unit Status' is not available.
> > > >
> > > > Do I have to configure BMC?
> > > > After BMC firmware update, I didn't change any configuration of BMC.
> > > >
> > > > Thanks,
> > > >
> > >
> > > Please, keep the flow of the e-mail consistent as well as
> > > ipmitool-dev in the loop, because that way you might get more
> > > answers and avoid couple other things.
> > >
> > > Anyway, to your server. I don't have access to these, so it is hard
> > > to
> > say.
> > > Yes, one option is to update BMC firmware, which should not reset
> > > its
> > > settings(note: should not). I would check changelogs to see whether
> > > there were some updates related to Power Supply or IPMI stack or alike.
> > >
> > > I'm not sure if any extra configuration of BMC is required, but
> > > again I have no experience with these servers.
> > >
> > > I'll keep thinking about it, but I'm not sure what I could come up
> with.
> > > Hmm if you check BMC/SP web interface, can you see readings of
> > > sensors there? Can you see readings of power supply there?
> > >
> > > I'm sorry I was not much of help.
> > >
> > > Z.
> > >
> > > >
> > > >
> > > > -----Original Message-----
> > > > From: Zdenek Styblik [mailto:zdenek.styb...@gmail.com]
> > > > Sent: Wednesday, September 21, 2011 6:00 PM
> > > > To: S. H. Lee
> > > > Cc: ipmitool-devel@lists.sourceforge.net
> > > > Subject: Re: [Ipmitool-devel] measuring the power consumption of a
> > > > server
> > > >
> > > > On Tue, Sep 20, 2011 at 10:18 PM, S. H. Lee <smil...@korea.ac.kr>
> > wrote:
> > > >> Hi,
> > > >>
> > > >> I have a SV7-2186 server with a S5500WBV motherboard and a Xeon
> > > processor.
> > > >> Its power supply is TDPS-600EB from DELTA.
> > > >>
> > > >> I am planning to develop a software checking the power
> > > >> consumption of a server.
> > > >>
> > > >> According to some documents, the power consumption can be checked
> > > >> through PSMI interface.
> > > >>
> > > >> Thus, I've tried to get the information by using ipmitool which
> > > >> can read FRU data from a power supply.
> > > >>
> > > >> But, the fru command of ipmitool on my server only shows the FRU
> > > >> data for a motherboard.
> > > >>
> > > >
> > > > Hello,
> > > >
> > > > what is # ipmitool sdr list; or # ipmitool sdr list all; telling you?
> > > > I have queried Sun/Oracle's
> > > > X4170 and X4270m2 and both are showing /SYS/VPS and PSx readings.
> > > > From
> > > here I get the Nac Names and then I would query FRUs directly eg. #
> > > ipmitool sensor reading /SYS/VPS; and stuff this data into RRD.
> > > >
> > > > Text above is just an example for inspiration and doesn't have to
> > > necessarily work for you.
> > > >
> > > > Anyway, try 'sdr list' and you will see, or should see, what
> > > > sensors you
> > > can query for readings.
> > > >
> > > > Best regards,
> > > > Zdenek
> > > >
> > > >>
> > > >>
> > > >> I want to know how to get the power consumption information of a
> > > >> server by using IPMItool.
> > > >>
> > > >>
> > > >>
> > > >> Waiting for your reply and guidance.
> > > >>
> > > >>
> > > >>
> > > >> Thanks.
> > > >>
> > > >
> > > >
> > > >
> > > >
> >
> >
> >
> > ----------------------------------------------------------------------
> > ----
> > ----
> > All the data continuously generated in your IT infrastructure contains
> > a definitive record of customers, application performance, security
> > threats, fraudulent activity and more. Splunk takes this data and
> > makes sense of
> it.
> > Business sense. IT sense. Common sense.
> > http://p.sf.net/sfu/splunk-d2dcopy1
> > _______________________________________________
> > Ipmitool-devel mailing list
> > Ipmitool-devel@lists.sourceforge.net
> > https://lists.sourceforge.net/lists/listinfo/ipmitool-devel
>
>
>
>
>
> ------------------------------------------------------------------------------
> All the data continuously generated in your IT infrastructure contains a
> definitive record of customers, application performance, security
> threats, fraudulent activity and more. Splunk takes this data and makes
> sense of it. Business sense. IT sense. Common sense.
> http://p.sf.net/sfu/splunk-d2dcopy1
> _______________________________________________
> Ipmitool-devel mailing list
> Ipmitool-devel@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/ipmitool-devel
>
------------------------------------------------------------------------------
All the data continuously generated in your IT infrastructure contains a
definitive record of customers, application performance, security
threats, fraudulent activity and more. Splunk takes this data and makes
sense of it. Business sense. IT sense. Common sense.
http://p.sf.net/sfu/splunk-d2dcopy1
_______________________________________________
Ipmitool-devel mailing list
Ipmitool-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/ipmitool-devel
