it sounds like it is being recognized. perhaps it just needs calibration? I recall there is an xinput_calibrator tool that you might be able to use to calibrate it. I don't remember if that tool was included in Tizen 2.0 though.
-Kevron On Thu, Sep 5, 2013 at 5:03 PM, Prabhuram Murugan < [email protected]> wrote: > Hi All, > > I am using TIZEN 2.0 ... > > Jeol, > > I gone through the changes, https://review.tizen.org/gerrit/#/c/6047/ , > but it is for Weston and TIZEN 3.0 > > however to fix this issues in TIZEN 2.0, I am looking in to > adaptation/xorg/driver/xserver-xorg-input-evdev > > can you advice, if this is the right point to start , > > Rusty, > Yes, we are using a single point, resistive touch screen device. > and from the mount point */dev/input/mouse1* looks it is detected as the > mouse device. > > TIZEN 2.0 doesnt support single touch device ? > > > > > On Fri, Sep 6, 2013 at 2:52 AM, Abramski, Adam M < > [email protected]> wrote: > >> I believe he mentions below that he's running 2.0, NOT 3.0. >> Adam >> >> -----Original Message----- >> From: [email protected] [mailto:[email protected]] >> On Behalf Of Rusty Lynch >> Sent: Thursday, September 05, 2013 8:58 AM >> To: Clark, Joel >> Cc: IVI Tizen >> Subject: Re: egalax touch screen not detected by X >> >> Actually... that fix only applies when you are using wayland. >> >> I'm not sure if you were using a touchscreen with the same issue, but we >> hit an issue when a vendor wired up an old style single point resistive >> screen on top of an egalax touchscreen controller, where weston didn't >> recognize the device as touch (since it didn't support the modern >> multipoint protocol), and treated it as a mouse, but then the device would >> emit TOUCH_BTN instead of a left or right mouse button. >> >> So... it actually worked, but no software is listening for this little >> known button value so kind of pointless. >> >> --rusty >> >> On Thu, 2013-09-05 at 14:21 +0000, Clark, Joel wrote: >> > This has been fixed in Tizen IVI 3.0 >> > https://bugs.tizen.org/jira/i#browse/TIVI-1086 >> > >> > >> > >> > You might want to look at these patches: >> > >> > https://bugs.freedesktop.org/show_bug.cgi?id=54428 >> > >> > >> > >> > https://review.tizen.org/gerrit/#/c/6047/ >> > >> > >> > >> > with the fix the touchscreen is no longer recognized as a mouse >> > device. >> > >> > >> > >> > Regards >> > >> > Joel >> > >> > >> > >> > >> > >> > From: [email protected] [mailto:[email protected]] >> > On Behalf Of Prabhuram Murugan >> > Sent: Thursday, September 05, 2013 5:38 AM >> > To: IVI Tizen >> > Subject: egalax touch screen not detected by X >> > >> > >> > >> > Hi , >> > >> > >> > I am using a USB based touch screen LCD for TIZEN on NDiS 166 board. >> > >> > >> > But the touch input is not working with this board. >> > I came across many bugs raised in TIZEN bug site, but they are mostly >> > for touch calibration. >> > >> > >> > In my case the touch screen is detected by the kernel but "xinput >> > list" doesnt list my touch screen device at all. Below are dmesg and >> > xinput list logs .... >> > >> > >> > I am using TIZEN 2.0 release. >> > >> > >> > >> > >> > >> > DMESG >> > >> > >> > [ 12.703678] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready >> > [ 21.528514] composite sync not supported >> > [ 884.484925] usb 2-1.1: USB disconnect, device number 3 [ >> > 885.940235] usb 2-1.1: new low-speed USB device number 7 using >> > ehci-pci [ 886.020179] usb 2-1.1: New USB device found, >> > idVendor=0eef, >> > idProduct=0001 >> > [ 886.020184] usb 2-1.1: New USB device strings: Mfr=1, Product=2, >> > SerialNumber=0 >> > [ 886.020188] usb 2-1.1: Product: USB TouchController [ 886.020191] >> > usb 2-1.1: Manufacturer: eGalax Inc. >> > [ 886.022735] input: eGalax Inc. USB TouchController as >> > /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1/2-1.1:1.0/input/input9 >> > >> > -sh-4.1# xinput list >> > ⎡ Virtual core pointer id=2 [master pointer >> > (3)] >> > ⎜ ↳ Virtual core XTEST pointer id=4 [slave >> > pointer (2)] >> > ⎜ ↳ SEJIN SEJIN USB Mini Trackball Keyboard id=11 [slave >> > pointer (2)] >> > ⎣ Virtual core keyboard id=3 [master keyboard >> > (2)] >> > ↳ Virtual core XTEST keyboard id=5 [slave >> > keyboard (3)] >> > ↳ SEJIN SEJIN USB Mini Trackball Keyboard id=10 [slave >> > keyboard (3)] >> > ∼ Power Button id=6 [floating slave] >> > ∼ Video Bus id=7 [floating slave] >> > ∼ Power Button id=8 [floating slave] >> > ∼ Microsoft LifeCam VX-800 id=9 [floating slave] >> > >> > #cat /dev/input/mouse1 >> > >> > )9 >> > >> > >> > >> > >> > Thanks and Regards, >> > Prabhuram M >> > >> > >> > _______________________________________________ >> > IVI mailing list >> > [email protected] >> > https://lists.tizen.org/listinfo/ivi >> >> >> _______________________________________________ >> IVI mailing list >> [email protected] >> https://lists.tizen.org/listinfo/ivi >> _______________________________________________ >> IVI mailing list >> [email protected] >> https://lists.tizen.org/listinfo/ivi >> > > > _______________________________________________ > IVI mailing list > [email protected] > https://lists.tizen.org/listinfo/ivi > >
_______________________________________________ IVI mailing list [email protected] https://lists.tizen.org/listinfo/ivi
