Hi Andy,
First a quick note before I answer your questions: please don't post
html messages here, use plain ASCII. It makes life easier for the rest
of us. Thanks.
On Saturday 25 March 2006 21:29, tv.mania wrote:
> Hi,
>
> My machine has 4 of 3 different cards (MPG600,PVR250,5000TVs) which
> work fine with ivtv-0.2.0-rc3e-paken patched driver previously. Today
> I upgrade the box to ivtv-0.6.1 and kernel 2.6.16 and the driver does
> not load correctly. Anything I missed?
>
> Thanks,
> Andy
>
> Here is the dmesg output:
> ivtv: ==================== START INIT IVTV ====================
> ivtv: version 0.6.1 (tagged release) loading
> ivtv: Linux version: 2.6.16 SMP preempt gcc-3.4
> ivtv: In case of problems please include the debug info between
> ivtv: the START INIT IVTV and END INIT IVTV lines, along with
> ivtv: any module options, when mailing the ivtv-users mailinglist.
> ivtv0: Autodetected Yuan MPG600/Kuroutoshikou ITVC16-STVLP card
> (cx23416 based) ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 21 (level,
> low) -> IRQ 193 saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver
> #0)
> tuner 1-0060: All bytes are equal. It is not a TEA5767
> tuner 1-0060: chip found @ 0xc0 (ivtv i2c driver #0)
> ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
> ivtv0: Encoder revision: 0x02050032
> ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB
> total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers
> (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472
> buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream:
> 455 x 4608 buffers (2048KB total) tuner 1-0060: type set to 53
> (Philips FQ1286)
> ivtv0: Initialized Yuan MPG600/Kuroutoshikou ITVC16-STVLP, card #0
> ivtv: ====================== NEXT CARD ======================
> ivtv1: Autodetected Hauppauge WinTV PVR-250 card (cx23415 based)
> ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 22 (level, low) -> IRQ
> 177 saa7115 2-0021: saa7115 found @ 0x42 (ivtv i2c driver #1)
> tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #1)
> tveeprom 2-0050: Hauppauge model 48011, rev F610, serial# 5193997
> tveeprom 2-0050: tuner model is Philips FI1236 MK2 (idx 10, type 2)
> tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08)
> tveeprom 2-0050: audio processor is MSP3435 (idx 10)
> tveeprom 2-0050: decoder processor is SAA7115 (idx 19)
> tveeprom 2-0050: has no radio, has IR remote
> msp3400: Unknown parameter `simpler'
^^^^^^^^^^^^^
Don't use any module options with msp3400. In fact, you rarely if ever
need module options anymore with ivtv-0.4.x and up. msp3400 no longer
recognizes this option and so will fail to load, hence leading to the
other errors.
> ivtv1: Failed to load module msp3400
> ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
> ivtv1: loaded v4l-cx2341x-dec.fw firmware (262144 bytes)
> ivtv1: Encoder revision: 0x02050032
> ivtv1: Decoder revision: 0x02020023
> ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB
> total) ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers
> (2048KB total) ivtv1: Allocate DMA encoder VBI stream: 120 x 17472
> buffers (2048KB total) ivtv1: Allocate DMA encoder PCM audio stream:
> 455 x 4608 buffers (2048KB total) tuner 2-0061: type set to 2
> (Philips NTSC (FI1236,FM1236 and compatibles)) ivtv1: i2c hardware
> 0x00000008 not found for command 0xc008561c! ivtv1: i2c addr 0x40 not
> found for command 0x40086d11!
> ivtv1: i2c addr 0x40 not found for command 0xc008561c!
> ivtv1: i2c hardware 0x00000008 not found for command 0xc008561c!
> ivtv1: i2c hardware 0x00000008 not found for command 0xc008561c!
> ivtv1: i2c hardware 0x00000008 not found for command 0xc008561c!
> ivtv1: Initialized Hauppauge WinTV PVR-250, card #1
> ivtv: ====================== NEXT CARD ======================
> ivtv2: Autodetected Nagase Transgear 5000TV card (cx23416 based)
> ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 23 (level, low) -> IRQ
> 201 saa7115 3-0021: saa7115 found @ 0x42 (ivtv i2c driver #2)
> tuner 3-0060: All bytes are equal. It is not a TEA5767
> tuner 3-0060: chip found @ 0xc0 (ivtv i2c driver #2)
> tda9887 3-0043: chip found @ 0x86 (ivtv i2c driver #2)
> ivtv2: Failed to load module upd64031a
> ivtv2: Failed to load module upd64083
^^^^^^^^^^^^^
These modules should have been build and installed. Can you check if
they are installed to the correct place? There is also an outside
chance that you need to run 'depmod' first.
Hans
> ivtv2: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
> ivtv2: Encoder revision: 0x02050032
> ivtv2: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB
> total) ivtv2: Allocate DMA encoder YUV stream: 194 x 10800 buffers
> (2048KB total) ivtv2: Allocate DMA encoder VBI stream: 120 x 17472
> buffers (2048KB total) ivtv2: Allocate DMA encoder PCM audio stream:
> 455 x 4608 buffers (2048KB total) tuner 3-0060: type set to 53
> (Philips FQ1286)
> ivtv2: i2c addr 0x12 not found for command 0xc0045627!
> ivtv2: i2c addr 0x5c not found for command 0xc0045627!
> ivtv2: Initialized Nagase Transgear 5000TV, card #2
> ivtv: ====================== NEXT CARD ======================
> ivtv3: Autodetected Nagase Transgear 5000TV card (cx23416 based)
> ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 20 (level, low) -> IRQ
> 225 saa7115 4-0021: saa7115 found @ 0x42 (ivtv i2c driver #3)
> tuner 4-0060: All bytes are equal. It is not a TEA5767
> tuner 4-0060: chip found @ 0xc0 (ivtv i2c driver #3)
> tda9887 4-0043: chip found @ 0x86 (ivtv i2c driver #3)
> ivtv3: Failed to load module upd64031a
> ivtv3: Failed to load module upd64083
> ivtv3: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
> ivtv3: Encoder revision: 0x02050032
> ivtv3: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB
> total) ivtv3: Allocate DMA encoder YUV stream: 194 x 10800 buffers
> (2048KB total) ivtv3: Allocate DMA encoder VBI stream: 120 x 17472
> buffers (2048KB total) ivtv3: Allocate DMA encoder PCM audio stream:
> 455 x 4608 buffers (2048KB total) tuner 4-0060: type set to 53
> (Philips FQ1286)
> ivtv3: i2c addr 0x12 not found for command 0xc0045627!
> ivtv3: i2c addr 0x5c not found for command 0xc0045627!
> ivtv3: Initialized Nagase Transgear 5000TV, card #3
> ivtv: ==================== END INIT IVTV ====================
_______________________________________________
ivtv-devel mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-devel
