Hi,
I'm attempting to bring up a PVR-150 in a machine that already had
a running PVR-250. Now neither card appears to be working. Wath TV is
a dark screen with some wavey lines in it. No audio. Is there any
known reason this cannot work? I can try a newer (or older) version of
ivtv if there's a good reason to do so.
Here's the card info. The two are very similar. (0003 vs. 0009)
Which is which?
0000:01:01.0 Multimedia video controller: Internext Compression Inc
iTVC16 (CX23416) MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc.: Unknown device 0003
Flags: bus master, medium devsel, latency 64, IRQ 22
Memory at f0000000 (32-bit, prefetchable)
Capabilities: [44] Power Management version 2
0000:01:02.0 Multimedia video controller: Internext Compression Inc
iTVC16 (CX23416) MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc.: Unknown device 0009
Flags: bus master, medium devsel, latency 64, IRQ 17
Memory at f4000000 (32-bit, prefetchable)
Capabilities: [44] Power Management version 2
dmesg is very messy now. I've asked about this message before:
ivtv: Encoder Firmware may be buggy, use version 0x02040011
but don't think I got an answer. Is it contributing to the problems?
dmesg output:
Linux video capture interface: v1.00
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.3.6 (p) loading
ivtv: Linux version: 2.6.11-gentoo-r11 preempt PENTIUM4 gcc-3.3
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: Unknown card: vendor/device: 4444/0016, subsystem vendor/device:
0070/0003ivtv: Defaulting to WinTV PVR 250 card
ivtv: Please mail the vendor/device and subsystem vendor/device IDs
and what kind of
ivtv: card you have to the ivtv-devel mailinglist:
http://sourceforge.net/projects/ivtv
ivtv: Prefix your subject line with [UNKNOWN CARD].
ivtv: Found an iTVC16 based chip
ACPI: PCI interrupt 0000:01:01.0[A] -> GSI 22 (level, low) -> IRQ 22
ivtv: Unreasonably low latency timer, setting to 64 (was 32)
ivtv: XXX PCI device: 0x2570 vendor: 0x8086
tveeprom: Hauppauge: model = 26032, rev = C199, serial# = 8095579
tveeprom: tuner = TCL 2002N 5H (idx = 99, type = 50)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio_processor = TDA9850 (type = 3)
ivtv: i2c attach [client=tveeprom[50],ok]
ivtv: Tuner Type 50, Tuner formats 0x00001000, Radio: yes, Model
0x008d1659, Revision 0x00000000
ivtv: NTSC tuner detected
ivtv: Radio detected
tuner: Ignoring new-style parameters in presence of obsolete ones
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv: i2c attach [client=(tuner unset),ok]
saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
ivtv: Encoder revision: 0x02040024
ivtv: Encoder Firmware may be buggy, use version 0x02040011
ivtv: Configuring WinTV PVR 250 card with 5 streams
ivtv: Registered v4l2 device for encoder MPEG minor 0
ivtv: Create DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv: Registered v4l2 device for encoder YUV minor 32
ivtv: Create DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv: Registered v4l2 device for encoder VBI minor 224
ivtv: Create DMA encoder VBI stream: 240 x 8736 buffers (2048KB total)
ivtv: Registered v4l2 device for encoder PCM audio minor 24
ivtv: Create DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv: Registered v4l2 device for encoder radio minor 64
ivtv: Create encoder radio stream
ivtv: Setting Tuner 50
tuner: type set to 50 (TCL 2002N) by ivtv i2c driver #0
ivtv: i2c client addr: 0x21 not found for command 1074029571!
ivtv: i2c client addr: 0x21 not found for command 1074029572!
ivtv: Setting audio matrix to input 3, output 1
ivtv: i2c client addr: 0x40 not found for command 1074294033!
ivtv: i2c client addr: 0x40 not found for command 2150135312!
ivtv: i2c client addr: 0x40 not found for command 1076393489!
ivtv: Switching standard to NTSC.
ivtv: i2c client addr: 0x40 not found for command 1076917763!
ivtv: i2c client addr: 0x21 not found for command 1074029571!
ivtv: Initialized WinTV PVR 250, card #0
ivtv: Autodetected WinTV PVR 150 card
ivtv: Found an iTVC16 based chip
ACPI: PCI interrupt 0000:01:02.0[A] -> GSI 17 (level, low) -> IRQ 17
ivtv: Unreasonably low latency timer, setting to 64 (was 32)
ivtv: XXX PCI device: 0x2570 vendor: 0x8086
ivtv: ivtv_enc_thread: pid = 4658, itv = 0xdf9e4620
ivtv: ivtv_enc_vbi_thread: pid = 4659, itv = 0xdf9e4620
tveeprom: Hauppauge: model = 32062, rev = C182, serial# = 7913638
tveeprom: tuner = LG TAPC H791F (idx = 82, type = 39)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio_processor = MSP3445 (type = 12)
ivtv: i2c attach [client=tveeprom[50],ok]
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1
ivtv: i2c attach [client=(tuner unset),ok]
saa7115: starting probe for adapter ivtv i2c driver #1 (0x10005)
saa7115: detecting saa7115 client on address 0x42
saa7115: writing init values
ivtv: i2c attach [client=saa7115[50],ok]
saa7115: status: (1E) 0x00, (1F) 0x40
msp34xx: ivtv version
msp34xx: init: chip=MSP3445G-B8, has NICAM support, simple (D) mode,
simpler (G) no-thread mode
msp34xx: $Id$ compiled on: Jun 24 2005 08:27:09
ivtv: i2c attach [client=MSP3445G-B8,ok]
ivtv: Tuner Type 39, Tuner formats 0x00001000, Radio: yes, Model
0x008d1612, Revision 0x00000000
ivtv: Radio detected
cx25840: starting probe for adapter ivtv i2c driver #0 (0x10005)
cx25840: detecting cx25840 client on address 0x88
cx25840: cx25841-23 found. Initializing...
cx25840: requesting /lib/modules/HcwMakoA.ROM
cx25840: firmware loaded
ivtv: i2c attach [client=cx25840[50],ok]
cx25840: starting probe for adapter ivtv i2c driver #1 (0x10005)
ivtv: i2c attach [client=wm8775[50],ok]
ivtv: Encoder revision: 0x02040024
ivtv: Encoder Firmware may be buggy, use version 0x02040011
ivtv: Configuring WinTV PVR 150 card with 5 streams
ivtv: Registered v4l2 device for encoder MPEG minor 1
ivtv: Create DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv: Registered v4l2 device for encoder YUV minor 33
ivtv: Create DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv: Registered v4l2 device for encoder VBI minor 225
ivtv: Create DMA encoder VBI stream: 240 x 8736 buffers (2048KB total)
ivtv: Registered v4l2 device for encoder PCM audio minor 25
ivtv: Create DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv: Registered v4l2 device for encoder radio minor 65
ivtv: Create encoder radio stream
ivtv: Setting Tuner 39
tuner: type set to 39 (LG NTSC (newer TAPC series)) by ivtv i2c driver #1
ivtv: i2c client addr: 0x44 not found for command 1074029571!
ivtv: i2c client addr: 0x44 not found for command 1074029572!
ivtv: i2c client addr: 0x44 not found for command 1074029678!
ivtv: Switching standard to NTSC.
ivtv: i2c client addr: 0x44 not found for command 1074029571!
ivtv: Initialized WinTV PVR 150, card #1
ivtv: ==================== END INIT IVTV ====================
ivtv: ivtv_enc_thread: pid = 4688, itv = 0xdfa078fc
ivtv: ivtv_enc_vbi_thread: pid = 4689, itv = 0xdfa078fc
<SNIP>
ivtv: i2c client addr: 0x21 not found for command 2150392936!
ivtv: i2c client addr: 0x21 not found for command 1074684935!
ivtv: i2c client addr: 0x21 not found for command 2150392936!
ivtv: i2c client addr: 0x21 not found for command 1074684935!
ivtv: i2c client addr: 0x21 not found for command 2150392936!
ivtv: i2c client addr: 0x21 not found for command 1074684935!
ivtv: i2c client addr: 0x21 not found for command 2150392936!
ivtv: i2c client addr: 0x21 not found for command 1074684935!
ivtv: i2c client addr: 0x40 not found for command 2150135312!
ivtv: i2c client addr: 0x40 not found for command 1076393489!
ivtv: i2c client addr: 0x21 not found for command 1074029574!
ivtv: i2c client addr: 0x40 not found for command 1074034191!
ivtv: i2c client addr: 0x21 not found for command 1074029574!
ivtv: i2c client addr: 0x40 not found for command 2150135312!
ivtv: i2c client addr: 0x40 not found for command 1076393489!
mtrr: base(0xe8020000) is not aligned on a size(0x400000) boundary
If I try to watch TV in Myth I get more messages:
ivtv: i2c client addr: 0x21 not found for command 2150392936!
ivtv: i2c client addr: 0x21 not found for command 1074684935!
ivtv: i2c client addr: 0x21 not found for command 2150392936!
ivtv: i2c client addr: 0x21 not found for command 1074684935!
ivtv: i2c client addr: 0x21 not found for command 2150392936!
ivtv: i2c client addr: 0x21 not found for command 1074684935!
ivtv: i2c client addr: 0x21 not found for command 2150392936!
ivtv: i2c client addr: 0x21 not found for command 1074684935!
ivtv: i2c client addr: 0x21 not found for command 1075864679!
ivtv: i2c client addr: 0x40 not found for command 2150135312!
ivtv: i2c client addr: 0x40 not found for command 1076393489!
ivtv: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv: i2c client addr: 0x21 not found for command 1074029670!
ivtv: Setup VBI API header 0x0000bd0d pkts 1 buffs 4 ln 24 sz 1456
ivtv: Setup VBI start 0x0018ea04 frames 4 fpi 1 lines 0x000000f1
ivtv: i2c client addr: 0x21 not found for command 1074029574!
ivtv: i2c client addr: 0x21 not found for command 1074029574!
ivtv: i2c client addr: 0x21 not found for command 2150392936!
ivtv: i2c client addr: 0x21 not found for command 1074684935!
ivtv: i2c client addr: 0x21 not found for command 2150392936!
ivtv: i2c client addr: 0x21 not found for command 1074684935!
ivtv: i2c client addr: 0x21 not found for command 2150392936!
ivtv: i2c client addr: 0x21 not found for command 1074684935!
ivtv: i2c client addr: 0x21 not found for command 2150392936!
ivtv: i2c client addr: 0x21 not found for command 1074684935!
ivtv: i2c client addr: 0x21 not found for command 1075864679!
ivtv: i2c client addr: 0x40 not found for command 2150135312!
ivtv: i2c client addr: 0x40 not found for command 1076393489!
ivtv: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv: i2c client addr: 0x21 not found for command 1074029670!
ivtv: Setup VBI API header 0x0000bd0d pkts 1 buffs 4 ln 24 sz 1456
ivtv: Setup VBI start 0x0018ea04 frames 4 fpi 1 lines 0x000000f1
ivtv: i2c client addr: 0x21 not found for command 1074029574!
ivtv: i2c client addr: 0x21 not found for command 1074029574!
[EMAIL PROTECTED] ~ $ /sbin/lsmod
Module Size Used by
nfsd 90952 9
exportfs 5120 1 nfsd
snd_pcm_oss 49056 0
snd_mixer_oss 17920 1 snd_pcm_oss
snd_seq_oss 32640 0
snd_seq_midi_event 6272 1 snd_seq_oss
snd_seq 50192 4 snd_seq_oss,snd_seq_midi_event
snd_usb_audio 63552 0
snd_usb_lib 11520 1 snd_usb_audio
snd_rawmidi 20256 1 snd_usb_lib
snd_seq_device 7052 3 snd_seq_oss,snd_seq,snd_rawmidi
snd_intel8x0 29120 1
snd_ac97_codec 75512 1 snd_intel8x0
snd_pcm 83720 4
snd_pcm_oss,snd_usb_audio,snd_intel8x0,snd_ac97_codec
snd_timer 21764 2 snd_seq,snd_pcm
snd 47588 13
snd_pcm_oss,snd_mixer_oss,snd_seq_oss,snd_seq,snd_usb_audio,snd_rawmidi,snd_seq_device,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer
snd_page_alloc 7812 2 snd_intel8x0,snd_pcm
intel_mch_agp 8464 0
wm8775 9240 0
cx25840 42024 0
firmware_class 7808 1 cx25840
msp3400 27832 0
saa7115 12180 0
tuner 20644 0
tveeprom 12852 0
ivtv 1334596 0
i2c_algo_bit 9096 1 ivtv
i2c_core 18576 7
wm8775,cx25840,msp3400,saa7115,tuner,tveeprom,i2c_algo_bit
videodev 7552 1 ivtv
i915 17920 1
drm 60436 2 i915
intel_agp 20252 1
agpgart 28968 4 intel_mch_agp,drm,intel_agp
sbp2 22024 0
ieee1394 94260 1 sbp2
[EMAIL PROTECTED] ~ $
What can I do to try and get this working?
Thanks,
Mark
-------------------------------------------------------
SF.Net email is sponsored by: Discover Easy Linux Migration Strategies
from IBM. Find simple to follow Roadmaps, straightforward articles,
informative Webcasts and more! Get everything you need to get up to
speed, fast. http://ads.osdn.com/?ad_idt77&alloc_id492&op=click
_______________________________________________
ivtv-devel mailing list
ivtv-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/ivtv-devel
