On 6/28/05, Bryan Mayland <[EMAIL PROTECTED]> wrote: > Patch attached to fix this. It might also fix your problems below > too, so try that first.
Thanks Bryan. OK, the patch seems to have moved me forward but I'm still getting some i2c messages and no video/audio. Could the i2c stuff be due to the way I built the kernel and/or not modprobing the right i2c stuff? I assume it easily could be. I'm still getting a black screen with dark wavey lines. Since I had to put a splitter in to run two cable inputs inputs I removed it and hooked the cable TV cable back to the 250 but I'm still getting no video or audio. I'll grab a portable TV and check the splitter - it's an active splitter that I haven't used in a year or more - and make sure it's working while I wait and see what you think I might try next. Here's dmesg now. It's look better but no life yet. Linux video capture interface: v1.00 ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.3.6 (p) loading ivtv: Linux version: 2.6.11-gentoo-r11 preempt PENTIUM4 gcc-3.3 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: Autodetected WinTV PVR 250 card ivtv: Found an iTVC16 based chip ACPI: PCI interrupt 0000:01:01.0[A] -> GSI 22 (level, low) -> IRQ 22 ivtv: Unreasonably low latency timer, setting to 64 (was 32) ivtv: XXX PCI device: 0x2570 vendor: 0x8086 Attached scsi removable disk sdd at scsi0, channel 0, id 0, lun 3 usb-storage: device scan complete tveeprom: Hauppauge: model = 26032, rev = C199, serial# = 8095579 tveeprom: tuner = TCL 2002N 5H (idx = 99, type = 50) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio_processor = TDA9850 (type = 3) ivtv: i2c attach [client=tveeprom[50],ok] ivtv: Tuner Type 50, Tuner formats 0x00001000, Radio: yes, Model 0x008d1659, Revision 0x00000000 ivtv: NTSC tuner detected ivtv: Radio detected tuner: Ignoring new-style parameters in presence of obsolete ones tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv: i2c attach [client=(tuner unset),ok] saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005) ivtv: Encoder revision: 0x02040024 ivtv: Encoder Firmware may be buggy, use version 0x02040011 ivtv: Configuring WinTV PVR 250 card with 5 streams ivtv: Registered v4l2 device for encoder MPEG minor 0 ivtv: Create DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv: Registered v4l2 device for encoder YUV minor 32 ivtv: Create DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv: Registered v4l2 device for encoder VBI minor 224 ivtv: Create DMA encoder VBI stream: 240 x 8736 buffers (2048KB total) ivtv: Registered v4l2 device for encoder PCM audio minor 24 ivtv: Create DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv: Registered v4l2 device for encoder radio minor 64 ivtv: Create encoder radio stream ivtv: Setting Tuner 50 tuner: type set to 50 (TCL 2002N) by ivtv i2c driver #0 ivtv: i2c client addr: 0x21 not found for command 1074029571! ivtv: i2c client addr: 0x21 not found for command 1074029572! ivtv: Setting audio matrix to input 3, output 1 ivtv: i2c client addr: 0x40 not found for command 1074294033! ivtv: i2c client addr: 0x40 not found for command 2150135312! ivtv: i2c client addr: 0x40 not found for command 1076393489! ivtv: Switching standard to NTSC. ivtv: i2c client addr: 0x40 not found for command 1076917763! ivtv: i2c client addr: 0x21 not found for command 1074029571! ivtv: Initialized WinTV PVR 250, card #0 ivtv: Autodetected WinTV PVR 150 card ivtv: Found an iTVC16 based chip ACPI: PCI interrupt 0000:01:02.0[A] -> GSI 17 (level, low) -> IRQ 17 ivtv: Unreasonably low latency timer, setting to 64 (was 32) ivtv: XXX PCI device: 0x2570 vendor: 0x8086 ivtv: ivtv_enc_thread: pid = 4658, itv = 0xdf9e4620 ivtv: ivtv_enc_vbi_thread: pid = 4659, itv = 0xdf9e4620 tveeprom: Hauppauge: model = 32062, rev = C182, serial# = 7913638 tveeprom: tuner = LG TAPC H791F (idx = 82, type = 39) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio_processor = MSP3445 (type = 12) ivtv: i2c attach [client=tveeprom[50],ok] tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1 ivtv: i2c attach [client=(tuner unset),ok] saa7115: starting probe for adapter ivtv i2c driver #1 (0x10005) saa7115: detecting saa7115 client on address 0x42 saa7115: writing init values ivtv: i2c attach [client=saa7115[50],ok] saa7115: status: (1E) 0x00, (1F) 0xc0 msp34xx: ivtv version msp34xx: init: chip=MSP3445G-B8, has NICAM support, simple (D) mode, simpler (G) no-thread mode msp34xx: $Id$ compiled on: Jun 28 2005 11:51:48 ivtv: i2c attach [client=MSP3445G-B8,ok] ivtv: Tuner Type 39, Tuner formats 0x00001000, Radio: yes, Model 0x008d1612, Revision 0x00000000 ivtv: Radio detected cx25840: starting probe for adapter ivtv i2c driver #0 (0x10005) cx25840: detecting cx25840 client on address 0x88 cx25840: cx25841-23 found. Initializing... cx25840: requesting /lib/modules/HcwMakoA.ROM cx25840: firmware loaded ivtv: i2c attach [client=cx25840[50],ok] cx25840: starting probe for adapter ivtv i2c driver #1 (0x10005) ivtv: i2c attach [client=wm8775[50],ok] ivtv: Encoder revision: 0x02040024 ivtv: Encoder Firmware may be buggy, use version 0x02040011 ivtv: Configuring WinTV PVR 150 card with 5 streams ivtv: Registered v4l2 device for encoder MPEG minor 1 ivtv: Create DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv: Registered v4l2 device for encoder YUV minor 33 ivtv: Create DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv: Registered v4l2 device for encoder VBI minor 225 ivtv: Create DMA encoder VBI stream: 240 x 8736 buffers (2048KB total) ivtv: Registered v4l2 device for encoder PCM audio minor 25 ivtv: Create DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv: Registered v4l2 device for encoder radio minor 65 ivtv: Create encoder radio stream ivtv: Setting Tuner 39 tuner: type set to 39 (LG NTSC (newer TAPC series)) by ivtv i2c driver #1 ivtv: i2c client addr: 0x44 not found for command 1074029571! ivtv: i2c client addr: 0x44 not found for command 1074029572! ivtv: i2c client addr: 0x44 not found for command 1074029678! ivtv: Switching standard to NTSC. ivtv: i2c client addr: 0x44 not found for command 1074029571! ivtv: Initialized WinTV PVR 150, card #1 ivtv: ==================== END INIT IVTV ==================== ivtv: ivtv_enc_thread: pid = 4688, itv = 0xdfa078fc ivtv: ivtv_enc_vbi_thread: pid = 4689, itv = 0xdfa078fc <SNIP> eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]). ivtv: i2c client addr: 0x21 not found for command 2150392936! ivtv: i2c client addr: 0x21 not found for command 1074684935! ivtv: i2c client addr: 0x21 not found for command 2150392936! ivtv: i2c client addr: 0x21 not found for command 1074684935! ivtv: i2c client addr: 0x21 not found for command 2150392936! ivtv: i2c client addr: 0x21 not found for command 1074684935! ivtv: i2c client addr: 0x21 not found for command 2150392936! ivtv: i2c client addr: 0x21 not found for command 1074684935! ivtv: i2c client addr: 0x40 not found for command 2150135312! ivtv: i2c client addr: 0x40 not found for command 1076393489! ivtv: i2c client addr: 0x21 not found for command 1074029574! ivtv: i2c client addr: 0x40 not found for command 1074034191! ivtv: i2c client addr: 0x21 not found for command 1074029574! ivtv: i2c client addr: 0x40 not found for command 2150135312! ivtv: i2c client addr: 0x40 not found for command 1076393489! mtrr: base(0xe8020000) is not aligned on a size(0x400000) boundary [EMAIL PROTECTED] ~ $ Cheers, Mark ------------------------------------------------------- SF.Net email is sponsored by: Discover Easy Linux Migration Strategies from IBM. Find simple to follow Roadmaps, straightforward articles, informative Webcasts and more! Get everything you need to get up to speed, fast. http://ads.osdn.com/?ad_idt77&alloc_id492&op=click _______________________________________________ ivtv-devel mailing list ivtv-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/ivtv-devel
