On Mon, 2005-12-26 at 22:48 -0700, Crazyguy78 Anderton wrote: > I am use the tutorial http://wilsonet.com/mythtv/fcmyth.php#getmythtv and > try to setup my Hauppauge PVR-250 get to the point here were need to enter > > /usr/bin/ivtvctl -u 0x3000 and when I enter it say's not an ivtv driver > device what I am I doing wrong.
I had this earlier this week when working on getting my card installed. It turned out there were previous module versions in a different location. Do a find for ivtv.ko and check date and timestamps. Regards, Des > vtv: ==================== START INIT IVTV ==================== > ivtv: version 0.4.1 (tagged release) loading > ivtv: Linux version: 2.6.14-1.1653_FC4 686 REGPARM 4KSTACKS gcc-4.0 > ivtv: In case of problems please include the debug info between > ivtv: the START INIT IVTV and END INIT IVTV lines, along with > ivtv: any module options, when mailing the ivtv-users mailinglist. > ivtv0: Autodetected WinTV PVR 250 card (cx23416 based) > ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> > IRQ 10 > ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50] > tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #0) > ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61] > tveeprom 2-0050: Hauppauge model 32032, rev B310, serial# 6983299 > tveeprom 2-0050: tuner model is Philips FI1236 MK2 (idx 10, type 2) > tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08) > tveeprom 2-0050: audio processor is MSP4448 (idx 27) > tveeprom 2-0050: decoder processor is SAA7115 (idx 19) > tveeprom 2-0050: has no radio, has IR remote > saa7115 2-0021: ivtv driver > saa7115 2-0021: saa7115 found @ 0x42 (ivtv i2c driver #0) > ivtv0: i2c attach to card #0 ok [client=saa7115, addr=21] > msp3400 2-0040: ivtv driver > msp3400 2-0040: chip=MSP4448G-A2 +nicam +simple +simpler +radio mode=simpler > ivtv0: i2c attach to card #0 ok [client=MSP4448G-A2, addr=40] > msp3400 2-0040: msp34xxg daemon started > ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) > ivtv0: Encoder revision: 0x02040024 > ivtv0 warning: Encoder Firmware can be buggy, use version 0x02040011 or > 0x02050032. > ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) > ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) > ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) > ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB > total) > tuner 2-0061: type set to 2 (Philips NTSC (FI1236,FM1236 and compatibles)) > ivtv0: Initialized WinTV PVR 250, card #0 > ivtv: ==================== END INIT IVTV ==================== > > 00:0c.0 Multimedia video controller: Internext Compression Inc iTVC16 > (CX23416) MPEG-2 Encoder (rev 01) > Subsystem: Hauppauge computer works Inc. WinTV PVR 250 > Flags: bus master, medium devsel, latency 64, IRQ 10 > Memory at e4000000 (32-bit, prefetchable) [size=64M] > Capabilities: [44] Power Management version 2 > thanks > [EMAIL PROTECTED] > > > > _______________________________________________ > ivtv-users mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-users -- Des Dougan, Principal Dougan Consulting Group Ph: 604-980-2848 Email: des at DouganConsulting dot com www.DouganConsulting.com Design - Implementation - Support _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
