Please update to 0.4.2, remove the ivtv options from modprobe (why do
people keep setting options?) tune to a known good channel and run
ivtvctl --log-status. Please report the output.
Thanks,
Hans
On Tuesday 17 January 2006 01:30, [EMAIL PROTECTED] wrote:
> I still do not have sound working on tuner0 or tuner1. I have
> modified my modprobe.conf and firmware files, so here is an update. I
> no longer receieve messages about buggy firmware.
>
> Again, my problem is a Hauppage WinTV PVR500 with dual tuners. They
> both work fine for video but there is no audio on MythTV or when I
> cat /dev/video0 to a mpg and use mplayer or xine to play it. All
> volume controls I can find are turned up all the way.
>
> As an important note, the volume in ivtvctl says mute=1, and using
> ivtvctl -y mute=0 does not set the mute to 0, despite it saying OK.
>
> Here are my updated modconf and dmesg ivtv outputs:
> Linux video capture interface: v1.00
> ivtv: ==================== START INIT IVTV ====================
> ivtv: version 0.4.1 (tagged release) loading
> ivtv: Linux version: 2.6.14-1.1656_FC4smp SMP 686 REGPARM 4KSTACKS
> gcc-4.0 ivtv: In case of problems please include the debug info
> between ivtv: the START INIT IVTV and END INIT IVTV lines, along
> with ivtv: any module options, when mailing the ivtv-users
> mailinglist. ivtv0: User specified WinTV PVR 150 card (detected
> cx23416 based chip) ACPI: PCI Interrupt 0000:04:08.0[A] -> GSI 25
> (level, low) -> IRQ 201 ivtv0: i2c attach to card #0 ok
> [client=tveeprom, addr=50]
> tveeprom 1-0050: Hauppauge model 23552, rev D492, serial# 8023885
> tveeprom 1-0050: tuner model is Philips FQ1236A MK4 (idx 92, type 57)
> tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
> tveeprom 1-0050: second tuner model is Philips TEA5767HN FM Radio
> (idx 101, type 62)
> tveeprom 1-0050: audio processor is CX25843 (idx 37)
> tveeprom 1-0050: decoder processor is CX25843 (idx 30)
> tveeprom 1-0050: has radio, has no IR remote
> ivtv0: This is the first unit of a PVR500
> tuner 1-0060: chip found @ 0xc0 (ivtv i2c driver #0)
> tuner 1-0060: TEA5767 detected.
> ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=60]
> tuner 1-0060: type set to 62 (Philips TEA5767HN FM Radio)
> tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
> ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
> cx25840 1-0044: ivtv driver
> cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
> cx25840 1-0044: loaded v4l-cx25840.fw firmware (14264 bytes)
> ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44]
> wm8775 1-001b: ivtv driver
> wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
> ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b]
> tda9885/6/7: chip found @ 0x86
> ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43]
> ivtv0: Detected a TEA5767 radio tuner. Enabling radio support.
> ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
> ivtv0: Encoder revision: 0x02050032
> ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB
> total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers
> (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472
> buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream:
> 455 x 4608 buffers (2048KB total)
> ivtv0: Create encoder radio stream
> tuner 1-0061: type set to 57 (Philips FQ1236A MK4)
> ivtv0: Initialized WinTV PVR 500 (unit #1), card #0
> ivtv: ====================== NEXT CARD ======================
> ivtv1: Autodetected WinTV PVR 150 card (cx23416 based)
> ACPI: PCI Interrupt 0000:04:09.0[A] -> GSI 26 (level, low) -> IRQ 209
> ivtv1: i2c attach to card #1 ok [client=tveeprom, addr=50]
> tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #1)
> ivtv1: i2c attach to card #1 ok [client=(tuner unset), addr=61]
> cx25840 2-0044: ivtv driver
> cx25840 2-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1)
> cx25840 2-0044: loaded v4l-cx25840.fw firmware (14264 bytes)
> ivtv1: i2c attach to card #1 ok [client=cx25840, addr=44]
> wm8775 2-001b: ivtv driver
> wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #1)
> ivtv1: i2c attach to card #1 ok [client=wm8775, addr=1b]
> tda9885/6/7: chip found @ 0x86
> ivtv1: i2c attach to card #1 ok [client=tda9887, addr=43]
> tveeprom 2-0050: Hauppauge model 23552, rev D492, serial# 8023885
> tveeprom 2-0050: tuner model is Philips FQ1236A MK4 (idx 92, type 57)
> tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08)
> tveeprom 2-0050: second tuner model is Philips TEA5767HN FM Radio
> (idx 101, type 62)
> tveeprom 2-0050: audio processor is CX25843 (idx 37)
> tveeprom 2-0050: decoder processor is CX25843 (idx 30)
> tveeprom 2-0050: has radio, has no IR remote
> ivtv1: This is the first unit of a PVR500
> ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
> ivtv1: Encoder revision: 0x02050032
> ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB
> total) ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers
> (2048KB total) ivtv1: Allocate DMA encoder VBI stream: 120 x 17472
> buffers (2048KB total) ivtv1: Allocate DMA encoder PCM audio stream:
> 455 x 4608 buffers (2048KB total)
> ivtv1: Create encoder radio stream
> tuner 2-0061: type set to 57 (Philips FQ1236A MK4)
> ivtv1: Initialized WinTV PVR 500 (unit #1), card #1
> ivtv: ==================== END INIT IVTV ====================
>
> modprobbe.conf:
> alias eth0 e1000
> alias snd-card-0 snd-intel8x0
> options snd-card-0 index=0
> options snd-intel8x0 index=0
> remove snd-intel8x0 { /usr/sbin/alsactl store 0 >/dev/null 2>&1 || :
> ; }; /sbin/modprobe -r --ignore-remove snd-intel8x0
> alias usb-controller ehci-hcd
> alias usb-controller1 uhci-hcd
> alias ieee1394-controller ohci1394
> # nvidia kernel module
> alias char-major-195 nvidia-1_0-7667
> alias nvidia nvidia-1_0-7667
> # ivtv (pvr-500)
> alias char-major-81 ivtv
> alias char-major-81-0 ivtv
> alias char-major-81-1 ivtv
> options ivtv ivtv_std=1 tuner=57,57 cardtype=6
>
> Any help in getting sound working would be much appreciated! Sound
> card is working btw, if I use play and tell it to play a .wav file or
> something.
>
> Thanks!
> - Chris Thielen
>
> > I found a page,
> > http://ivtv.writeme.ch/tiki-index.php?page=FirmwareVersions, that
> > seems to list a lot of firmware revisions for Hauppage cards, and I
> > downloaded the one recommended for ivtv 0.3.9 or later (I'm running
> > 0.4.1) but the zip file only contains .inf and .sys files, yet my
> > /lib/modules/ directory for ivtv has .rom and .bin files. How do I
> > use these recommended firmware files to see if it is indeed the
> > cause of my no sound on a PVR500?
> >
> > Thanks,
> > Chris Thielen
> >
> >>> ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
> >>> ivtv0: Encoder revision: 0x02040024
> >>> ivtv0 warning: Encoder Firmware can be buggy, use version
> >>> 0x02040011 or 0x02050032.
> >>>
> >>> >> What should I try?
> >>
> >> it might be nothing, but i would try to fix this first.
> >>
> >> Chris
> >>
> >>
> >> _______________________________________________
> >> ivtv-users mailing list
> >> [email protected]
> >> http://ivtvdriver.org/mailman/listinfo/ivtv-users
> >
> > _______________________________________________
> > ivtv-users mailing list
> > [email protected]
> > http://ivtvdriver.org/mailman/listinfo/ivtv-users
>
> _______________________________________________
> ivtv-users mailing list
> [email protected]
> http://ivtvdriver.org/mailman/listinfo/ivtv-users
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
