Hello all,
This is my first request and last ditch effort to get my PVR 150 working
on Suse 10 (or ANY distro). I have tryed several versions of IVTV but
have not been able to get it working. Please help, I've done endless
searches on the Net and feel I have gotten "close". My dmesg output is
listed below. At first I had difficulty changing to the newest version
of IVTV but as you can see below I have now got it to be recognized. The
problem seems to be with the lower section (encoders/decoders). One
thing I noticed that is suspect is that I could not establish the
"symbolic link" because there were some strange dvb drivers in the
firware hotplug directory. I've since removed them but have no idea how
to establish a symbolic link or what it means (sorry, I'm no expert in
Linux - A newbie who's been torchering himself for TOO long). I'm about
to by an Avermedia card.
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.4.2 (tagged release) loading
ivtv: Linux version: 2.6.13-15.7-default 586 REGPARM gcc-4.0
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.14.9 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413)
wlan: 0.8.6.0 (EXPERIMENTAL)
ath_rate_sample: module not supported by Novell, setting U taint flag.
ath_rate_sample: no version for "ether_sprintf" found: kernel tainted.
ath_rate_sample: 1.2
ath_pci: 0.9.6.0 (EXPERIMENTAL)
intel8x0_measure_ac97_clock: measured 54295 usecs
intel8x0: clocking to 48000
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNKD] -> GSI 10 (level,
low) -> IRQ 10
ohci_hcd 0000:02:01.0: OHCI Host Controller
ohci_hcd 0000:02:01.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:02:01.0: irq 10, io mem 0xfeafd000
bootsplash: status on console 0 changed to on
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:02:01.1[B] -> Link [LNKC] -> GSI 11 (level,
low) -> IRQ 11
ohci_hcd 0000:02:01.1: OHCI Host Controller
ohci_hcd 0000:02:01.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:02:01.1: irq 11, io mem 0xfeafe000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:02:01.2[C] -> Link [LNKH] -> GSI 5 (level, low)
-> IRQ 5
ehci_hcd 0000:02:01.2: EHCI Host Controller
ehci_hcd 0000:02:01.2: new USB bus registered, assigned bus number 4
ehci_hcd 0000:02:01.2: irq 5, io mem 0xfeaffc00
ehci_hcd 0000:02:01.2: USB 2.0 initialized, EHCI 0.95, driver 10 Dec
2004
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 5 ports detected
ACPI: PCI Interrupt 0000:02:0b.0[A] -> Link [LNKH] -> GSI 5 (level, low)
-> IRQ 5
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 11
ACPI: PCI Interrupt 0000:02:0d.0[A] -> Link [LNKF] -> GSI 11 (level,
low) -> IRQ 11
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:02:0d.0: 3Com PCI 3c905B Cyclone 100baseTx at 0xdc00. Vers LK1.1.19
ivtv0: Autodetected WinTV PVR 150 card (cx23416 based)
gameport: EMU10K1 is pci0000:02:0b.1/gameport0, io 0xdff0, speed 903kHz
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11
ACPI: PCI Interrupt 0000:02:0a.0[A] -> Link [LNKG] -> GSI 11 (level,
low) -> IRQ 11
Build date: Nov 29 2005
Debugging version (IEEE80211)
ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps
24Mbps 36Mbps 48Mbps 54Mbps
ath0: H/W encryption support: WEP AES AES_CCM TKIP
ath0: mac 5.6 phy 4.1 radio 1.7
ath0: Use hw queue 1 for WME_AC_BE traffic
ath0: Use hw queue 0 for WME_AC_BK traffic
ath0: Use hw queue 2 for WME_AC_VI traffic
ath0: Use hw queue 3 for WME_AC_VO traffic
ath0: Use hw queue 8 for CAB traffic
ath0: Use hw queue 9 for beacons
Debugging version (ATH)
ath0: Atheros 5212: mem=0xfeae0000, irq=11
ACPI: PCI Interrupt 0000:02:0c.0[A] -> Link [LNKB] -> GSI 9 (level, low)
-> IRQ 9
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
tveeprom: module not supported by Novell, setting U taint flag.
tveeprom: ivtv version
tveeprom: Hauppauge: model = 26032, rev = C199, serial# = 8208538
tveeprom: tuner = TCL 2002N 5H (idx = 99, type = 50)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio processor = CX25841 (type = 23)
tveeprom: decoder processor = CX25841 (type = 1c)
ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
tuner: module not supported by Novell, setting U taint flag.
tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
cx25840: module not supported by Novell, setting U taint flag.
cx25840 1-0044: ivtv driver
cx25840 1-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0)
cx25840 1-0044: unable to open firmware v4l-cx25840.fw
ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44]
wm8775: module not supported by Novell, setting U taint flag.
wm8775 1-001b: ivtv driver
wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b]
tda9887: module not supported by Novell, setting U taint flag.
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
ivtv0: unable to open firmware v4l-cx2341x-enc.fw
ivtv0: did you put the firmware in the hotplug firmware directory?
ivtv0 warning: failed loading encoder firmware
ivtv0 warning: Error loading firmware -3!
ivtv0: Error -3 initializing firmware.
ivtv0: Error -12 on initialization
ivtv: probe of 0000:02:0c.0 failed with error -12
ivtv: ==================== END INIT IVTV ====================
here's what's in my firmware hotplug directory:
> linux:/usr/src/ivtv-0.4.2/utils # ls /usr/lib/hotplug/firmware
> . HcwFalcn.rom ivtv-fw-dec.bin v4l-cx2341x-dec.fw v4l-cx2341x-init.mpg
> .. HcwMakoA.ROM ivtv-fw-enc.bin v4l-cx2341x-enc.fw v4l-cx25840.fw
It's been almost a year since I first decided to build a MYTHTV box and
purchased a Hauppage PVR 150. I have tried Fedora 4, Ubuntu 5.10, Suse
9.3, 10.0, and various versions of Knoppmyth.
I would greatly appreciate any help. Windows Media Center is junk but it
works in under 2 hours :(
Thank you for your time.
-Matt
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
