Hans Verkuil wrote: > On Monday 11 September 2006 23:08, Petter Sundlöf wrote: >> I'm getting no audio when using my Hauppauge PVR 150 (non-MCE). >> >> I've tried 2.6.15 and 0.4, and both pvr_1.18.21.22254_inf.zip and >> pvr_1.18.21.22301_inf.zip firmwares. I'm using tuner=50 for the ivtv > > Use tuner=55. Tuner 50 is for NTSC, tuner 55 is for PAL. It will work a > lot better after that change :-) > > Hans
Unfortunately this doesn't affect audio. The video still looks the same as with 50. >> module. With kernel 2.6.17 I am using 0.7, and have tried both of the >> above mentioned firmware versions. >> >> I also tried patching ivtv-driver.c according to jstew's (a friendlt >> person in #mythtv-users) to enable the pvr150_workaround. (adding >> another itv->pvr150_workaround = 1; at row 515) >> >> mplayer reports >> >> AO: [alsa] 48000Hz 2ch s16le (2 bytes per sample). >> >> I've also tried fiddling with ivtvctl. >> >> ivtvctl --set-ctrl=mute=0 -d /dev/video0 >> >> has no effect >> >> But after I do ivtvctl --set-audio-input 1 >> >> I get some random clicks in both channels, alternating between left >> and right. Only when I set it to 1, ivtvctl --log-status says " >> cx25840 0-0044: Audio muted: no". But it also says " >> cx25840 0-0044: Audio microcontroller: stopped" >> With 0 it says Muted: yes, but Running. >> >> Here's the full output of ivtvctl --log-status as it appears on a >> default boot: >> >> (23:07:36) [EMAIL PROTECTED]:~$ ivtvctl --log-status >> ioctl VIDIOC_LOG_STATUS ok >> ivtv0: ================= START STATUS CARD #0 ================= >> tveeprom 0-0050: Hauppauge model 26034, rev C1B3, serial# 8823954 >> tveeprom 0-0050: tuner model is TCL M2523_3DB_E (idx 113, type 4) >> tveeprom 0-0050: TV standards PAL(B/G) PAL(D/D1/K) (eeprom 0x44) >> tveeprom 0-0050: audio processor is CX25842 (idx 36) >> tveeprom 0-0050: decoder processor is CX25842 (idx 29) >> tveeprom 0-0050: has no radio, has IR remote >> tuner 0-0061: Tuner mode: analog TV >> tuner 0-0061: Frequency: 203.25 MHz >> tuner 0-0061: Standard: 0x000000ff >> cx25840 0-0044: Video signal: present >> cx25840 0-0044: Detected format: PAL-BDGHI >> cx25840 0-0044: Detected audio mode: mono >> cx25840 0-0044: Detected audio standard: not defined >> cx25840 0-0044: Audio muted: yes >> cx25840 0-0044: Audio microcontroller: running >> cx25840 0-0044: Configured audio standard: automatic detection >> cx25840 0-0044: Configured audio system: automatic standard and >> mode detection >> cx25840 0-0044: Specified standard: PAL-BDGHI >> cx25840 0-0044: Specified video input: Composite 7 >> cx25840 0-0044: Specified audio input: Tuner (In8) >> cx25840 0-0044: Specified audioclock freq: 48000 Hz >> cx25840 0-0044: Preferred audio mode: stereo >> cx25840 0-0044: Selected 65 MHz format: autodetect >> cx25840 0-0044: Selected 45 MHz format: chroma >> wm8775 0-001b: Input: 2 >> ivtv0: ================== END STATUS CARD #0 ================== >> >> Any help would be greatly appreciated. >> >> Best regards, >> Petter Sundlöf >> >> _______________________________________________ >> ivtv-users mailing list >> [email protected] >> http://ivtvdriver.org/mailman/listinfo/ivtv-users > > _______________________________________________ > ivtv-users mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-users _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
