Urg, I didn't look carefully enough at your log: you're still using old
saa7115, msp3400 and tuner modules from ivtv-0.4. (see the 'ivtv i2c
driver' lines in the log for these modules.
Remove these ivtv-0.4 modules, use only the versions from the 2.6.18
kernel.
Hans
On Friday 17 November 2006 06:02, Matthew Daubenspeck wrote:
> I just upgraded to ivtv-0.8.0 from the 0.4.x version which was
> working perfectly. I have two PVR-250s in my slave backend that will
> no longer display video. I have even tried the most recent svn
> version of 0.8.x and I have the same result. If I cat /dev/video0 >
> foo.mpg, the file has the correct audio but the video is blank. Here
> is dmesg:
>
> ivtv: ==================== START INIT IVTV ====================
> ivtv: version 0.8.1 (development snapshot compiled on Thu Nov 16
> 23:42:33 2006) loading
> ivtv: Linux version: 2.6.18-gentoo-r2 preempt mod_unload K7 gcc-4.1
> ivtv: In case of problems please include the debug info between
> ivtv: the START INIT IVTV and END INIT IVTV lines, along with
> ivtv: any module options, when mailing the ivtv-users mailinglist.
> ivtv0: Autodetected Hauppauge card (cx23416 based)
> ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
> ACPI: PCI Interrupt 0000:05:09.0[A] -> Link [LNKB] -> GSI 5 (level,
> low) -> IRQ 5
> ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
> tveeprom 0-0050: Hauppauge model 32062, rev C199, serial# 8510215
> tveeprom 0-0050: tuner model is TCL 2002N 5H (idx 99, type 50)
> tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08)
> tveeprom 0-0050: audio processor is MSP3445 (idx 12)
> tveeprom 0-0050: decoder processor is SAA7115 (idx 19)
> tveeprom 0-0050: has no radio, has IR remote
> ivtv0: Autodetected Hauppauge WinTV PVR-250
> tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0)
> saa7115 0-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
> msp3400 0-0040: MSP3445G-B8 found @ 0x80 (ivtv i2c driver #0)
> msp3400 0-0040: MSP3445G-B8 supports radio, mode is autodetect and
> autoselect
> ivtv0: Encoder revision: 0x02050032
> ivtv0: Registered device video0 for encoder MPEG
> ivtv0: Registered device video32 for encoder YUV
> ivtv0: Registered device vbi0 for encoder VBI
> ivtv0: Registered device video24 for encoder PCM audio
> tuner 0-0061: type set to 50 (TCL 2002N)
> ivtv0: Initialized Hauppauge WinTV PVR-250, card #0
> ivtv: ====================== NEXT CARD ======================
> ivtv1: Autodetected Hauppauge card (cx23416 based)
> ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
> ACPI: PCI Interrupt 0000:05:0a.0[A] -> Link [LNKC] -> GSI 10 (level,
> low) -> IRQ 10
> ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
> tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #1)
> saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #1)
> msp3400 1-0040: MSP3445G-B8 found @ 0x80 (ivtv i2c driver #1)
> msp3400 1-0040: MSP3445G-B8 supports radio, mode is autodetect and
> autoselect
> tveeprom 1-0050: Hauppauge model 32062, rev C199, serial# 8245573
> tveeprom 1-0050: tuner model is TCL 2002N 5H (idx 99, type 50)
> tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
> tveeprom 1-0050: audio processor is MSP3445 (idx 12)
> tveeprom 1-0050: decoder processor is SAA7115 (idx 19)
> tveeprom 1-0050: has no radio, has IR remote
> ivtv1: Autodetected Hauppauge WinTV PVR-250
> ivtv1: Encoder revision: 0x02050032
> ivtv1: Registered device video1 for encoder MPEG
> ivtv1: Registered device video33 for encoder YUV
> ivtv1: Registered device vbi1 for encoder VBI
> ivtv1: Registered device video25 for encoder PCM audio
> tuner 1-0061: type set to 50 (TCL 2002N)
> ivtv1: Initialized Hauppauge WinTV PVR-250, card #1
> ivtv: ==================== END INIT IVTV ====================
>
> and:
>
> $ ivtv-detect
> driver: ivtv-0.8.1
> card: Hauppauge WinTV PVR-250, bus info 0000:05:09.0
> /dev/v4l/video32: YUV encoding (links: /dev/video0, /dev/video24,
> /dev/video32) /dev/v4l/vbi0: VBI encoding (links: /dev/vbi0)
>
> driver: ivtv-0.8.1
> card: Hauppauge WinTV PVR-250, bus info 0000:05:0a.0
> /dev/v4l/video33: YUV encoding (links: /dev/video1, /dev/video25,
> /dev/video33) /dev/v4l/vbi1: VBI encoding (links: /dev/vbi1)
>
> I am using a 2.6.18-gentoo-r2 kernel. I have also tried shutting the
> machine down for more then 30 seconds. Something strange is
> happening, because I have tried to downgrade to ivtv-0.7.1 and I now
> get the same result with it. What am I missing?
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
