No, I was confused. Sorry about that, just ignore my email. You have the
right modules loaded.
Hans
On Friday 17 November 2006 18:56, Matthew Daubenspeck wrote:
> Wow am I confused. I completely removed everything from /lib/modules
> and started over with the kernel. For some reason I can't seem to get
> the tveeprom module to build until I include:
>
> <M > Conexant 2388x (bt878 successor) support
>
> Is this correct? Under Encoders and Decoders ---> I have:
>
> <M> Micronas MSP34xx audio decoders
> <M> Conexant CX2341x MPEG encoders
> <M> Philips SAA7113/4/5 video decoders
>
> I also assume I need the "Enable Video For Linux API 1 compatible
> Layer" as well. Using ivtv-0.8.0 I get:
>
> ivtv0: Unknown card: vendor/device: 4444/0016
> ivtv0: subsystem vendor/device: 0070/f7f9
> ivtv0: cx23416 based
>
> I'm sure this is nothing more then my ignorance. It works great with
> 0.4.7, so I must have missed something.
>
> On Fri, Nov 17, 2006 at 02:53:43PM +0100, Hans Verkuil wrote:
> > Urg, I didn't look carefully enough at your log: you're still using
> > old saa7115, msp3400 and tuner modules from ivtv-0.4. (see the
> > 'ivtv i2c driver' lines in the log for these modules.
> >
> > Remove these ivtv-0.4 modules, use only the versions from the
> > 2.6.18 kernel.
> >
> > Hans
> >
> > On Friday 17 November 2006 06:02, Matthew Daubenspeck wrote:
> > > I just upgraded to ivtv-0.8.0 from the 0.4.x version which was
> > > working perfectly. I have two PVR-250s in my slave backend that
> > > will no longer display video. I have even tried the most recent
> > > svn version of 0.8.x and I have the same result. If I cat
> > > /dev/video0 > foo.mpg, the file has the correct audio but the
> > > video is blank. Here is dmesg:
> > >
> > > ivtv: ==================== START INIT IVTV ====================
> > > ivtv: version 0.8.1 (development snapshot compiled on Thu Nov 16
> > > 23:42:33 2006) loading
> > > ivtv: Linux version: 2.6.18-gentoo-r2 preempt mod_unload K7
> > > gcc-4.1 ivtv: In case of problems please include the debug info
> > > between ivtv: the START INIT IVTV and END INIT IVTV lines, along
> > > with ivtv: any module options, when mailing the ivtv-users
> > > mailinglist. ivtv0: Autodetected Hauppauge card (cx23416 based)
> > > ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
> > > ACPI: PCI Interrupt 0000:05:09.0[A] -> Link [LNKB] -> GSI 5
> > > (level, low) -> IRQ 5
> > > ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
> > > tveeprom 0-0050: Hauppauge model 32062, rev C199, serial# 8510215
> > > tveeprom 0-0050: tuner model is TCL 2002N 5H (idx 99, type 50)
> > > tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08)
> > > tveeprom 0-0050: audio processor is MSP3445 (idx 12)
> > > tveeprom 0-0050: decoder processor is SAA7115 (idx 19)
> > > tveeprom 0-0050: has no radio, has IR remote
> > > ivtv0: Autodetected Hauppauge WinTV PVR-250
> > > tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0)
> > > saa7115 0-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
> > > msp3400 0-0040: MSP3445G-B8 found @ 0x80 (ivtv i2c driver #0)
> > > msp3400 0-0040: MSP3445G-B8 supports radio, mode is autodetect
> > > and autoselect
> > > ivtv0: Encoder revision: 0x02050032
> > > ivtv0: Registered device video0 for encoder MPEG
> > > ivtv0: Registered device video32 for encoder YUV
> > > ivtv0: Registered device vbi0 for encoder VBI
> > > ivtv0: Registered device video24 for encoder PCM audio
> > > tuner 0-0061: type set to 50 (TCL 2002N)
> > > ivtv0: Initialized Hauppauge WinTV PVR-250, card #0
> > > ivtv: ====================== NEXT CARD ======================
> > > ivtv1: Autodetected Hauppauge card (cx23416 based)
> > > ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
> > > ACPI: PCI Interrupt 0000:05:0a.0[A] -> Link [LNKC] -> GSI 10
> > > (level, low) -> IRQ 10
> > > ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
> > > tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #1)
> > > saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #1)
> > > msp3400 1-0040: MSP3445G-B8 found @ 0x80 (ivtv i2c driver #1)
> > > msp3400 1-0040: MSP3445G-B8 supports radio, mode is autodetect
> > > and autoselect
> > > tveeprom 1-0050: Hauppauge model 32062, rev C199, serial# 8245573
> > > tveeprom 1-0050: tuner model is TCL 2002N 5H (idx 99, type 50)
> > > tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
> > > tveeprom 1-0050: audio processor is MSP3445 (idx 12)
> > > tveeprom 1-0050: decoder processor is SAA7115 (idx 19)
> > > tveeprom 1-0050: has no radio, has IR remote
> > > ivtv1: Autodetected Hauppauge WinTV PVR-250
> > > ivtv1: Encoder revision: 0x02050032
> > > ivtv1: Registered device video1 for encoder MPEG
> > > ivtv1: Registered device video33 for encoder YUV
> > > ivtv1: Registered device vbi1 for encoder VBI
> > > ivtv1: Registered device video25 for encoder PCM audio
> > > tuner 1-0061: type set to 50 (TCL 2002N)
> > > ivtv1: Initialized Hauppauge WinTV PVR-250, card #1
> > > ivtv: ==================== END INIT IVTV ====================
> > >
> > > and:
> > >
> > > $ ivtv-detect
> > > driver: ivtv-0.8.1
> > > card: Hauppauge WinTV PVR-250, bus info 0000:05:09.0
> > > /dev/v4l/video32: YUV encoding (links: /dev/video0,
> > > /dev/video24, /dev/video32) /dev/v4l/vbi0: VBI encoding (links:
> > > /dev/vbi0)
> > >
> > > driver: ivtv-0.8.1
> > > card: Hauppauge WinTV PVR-250, bus info 0000:05:0a.0
> > > /dev/v4l/video33: YUV encoding (links: /dev/video1,
> > > /dev/video25, /dev/video33) /dev/v4l/vbi1: VBI encoding (links:
> > > /dev/vbi1)
> > >
> > > I am using a 2.6.18-gentoo-r2 kernel. I have also tried shutting
> > > the machine down for more then 30 seconds. Something strange is
> > > happening, because I have tried to downgrade to ivtv-0.7.1 and I
> > > now get the same result with it. What am I missing?
> >
> > _______________________________________________
> > ivtv-users mailing list
> > [email protected]
> > http://ivtvdriver.org/mailman/listinfo/ivtv-users
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
