Andreas Falk wrote: > Hi, > > Installed Kubuntu 6.06 a few days ago and tried to install my tv card > and everything went smoothly until i checked with dmesg when it says > it couldnt load the firmware. > > I got this message: > > [4418363.991000] ivtv: ==================== START INIT IVTV > ==================== > [4418363.991000] ivtv: version 0.4.5 (tagged release) loading > [4418363.991000] ivtv: Linux version: 2.6.15-23-386 preempt 486 gcc-4.0 > [4418363.991000] ivtv: In case of problems please include the debug > info between > [4418363.991000] ivtv: the START INIT IVTV and END INIT IVTV lines, along > with > [4418363.991000] ivtv: any module options, when mailing the > ivtv-users mailinglist. > [4418363.991000] ivtv0: Autodetected WinTV PVR 150 card (cx23416 based) > [4418363.992000] ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 17 (level, > low) -> IRQ 233 > [4418364.045000] tveeprom: ivtv version > [4418364.045000] tveeprom: Hauppauge: model = 26034, rev = C197, > serial# = 8356864 > [4418364.045000] tveeprom: tuner = TCL 2002MB_3H (idx = 97, type = 55) > [4418364.045000] tveeprom: tuner fmt = PAL(B/G) PAL(D/K) (eeprom = > 0x44, v4l2 = 0x00000e07) > [4418364.045000] tveeprom: audio processor = CX25842 (type = 24) > [4418364.045000] tveeprom: decoder processor = CX25842 (type = 1d) > [4418364.045000] ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50] > [4418364.064000] tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv > i2c driver #0 > [4418364.064000] ivtv0: i2c attach to card #0 ok [client=(tuner unset), > addr=61] > [4418364.280000] cx25840 0-0044: cx25842-23 found @ 0x88 (ivtv i2c driver #0) > [4418364.327000] cx25840 0-0044: unable to open firmware v4l-cx25840.fw > [4418364.397000] ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44] > [4418364.424000] wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0) > [4418364.434000] ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b] > [4418365.094000] ivtv0: unable to open firmware v4l-cx2341x-enc.fw > [4418365.094000] ivtv0: did you put the firmware in the hotplug > firmware directory? > [4418365.094000] ivtv0 warning: failed loading encoder firmware > [4418365.094000] ivtv0 warning: Error loading firmware -3! > [4418365.094000] ivtv0: Error -3 initializing firmware. > [4418365.096000] ivtv0: Error -12 on initialization > [4418365.096000] ivtv: probe of 0000:02:01.0 failed with error -12 > [4418365.096000] ivtv: ==================== END INIT IVTV > ==================== > > It detected the right card (Hauppauge WinTV 150-pvr) and i am using > kernel 2.6.15-23-386. I followed the howto on the wiki to every point > and I am using ivtv 0.4.5. > > Someone knows what I should do?
Check if the firmware files are in /usr/lib/hotplug/firmware/. If not get them from [1] and unpack them into this folder. Greets Sander [1] http://dl.ivtvdriver.org/ivtv/firmware/firmware.tar.gz PS: HP CID, please start your own thread instead of hijacking someone else his thread. Thanks _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
