pdp wrote: > I have problems with the activation of my Hauppauge 350 TV card. > I've followed the guide at edgy IVTV guide > (https://help.ubuntu.com/community/Install_IVTV_Edgy) > <https://help.ubuntu.com/community/Install_IVTV_Edgy> > As far as I can judge the activation of the IVTV driver was succesfull. > Also the setting of the frequency went ok: > > ivtv-tune -t europe-west -c E12 ==> /dev/video0: 224.250 MHz > > (I'm living in Belgium. Our television distributor is Telenet. 224.250 > Mhz is the frequency for the VTM channel) > > But when I issue: mplayer /dev/video0 I get only a screen with noise > > For the moment I'm a bit disappointed because the reason I bought the > 350 was because it was one of the cards that was best supported > under Linux. Therefore I've the feeling that may be some detail > (ivtvctl setting ?) must be changed but I have no clue what I should try > > I hope someone can help me solve this problem. > Thank you for taking time to look into this problem. > > Best regards, > > Peter > > Information regarding my setup: > > - the card works under Windows XP so the hardware is ok > - I'm using Ubuntu Edge as my main OS > - output of uname -a: Linux test 2.6.17-10-generic #2 SMP Fri Oct 13 > 18:45:35 UTC 2006 i686 GNU/Linux > - output of dmesg: > > [17179586.036000] ivtv: ==================== START INIT IVTV > ==================== > [17179586.036000] ivtv: version 0.7.0 (tagged release) loading > [17179586.036000] ivtv: Linux version: 2.6.17-10-generic SMP mod_unload > 586 REGPARM gcc-4.1 > [17179586.036000] ivtv: In case of problems please include the debug > info between > [17179586.036000] ivtv: the START INIT IVTV and END INIT IVTV lines, > along with > [17179586.036000] ivtv: any module options, when mailing the ivtv-users > mailinglist. > [17179586.068000] bcm43xx driver > [17179586.424000] NET: Registered protocol family 17 > [17179586.600000] ivtv0: Autodetected Hauppauge WinTV PVR-350 card > (cx23415 based) > [17179586.600000] ACPI: PCI Interrupt 0000:01:01.0[A] -> GSI 21 (level, > low) -> IRQ 66 > [17179586.644000] tveeprom 0-0050: Hauppauge model 48139, rev K2B7, > serial# 8889298 > [17179586.644000] tveeprom 0-0050: tuner model is Philips FM1216ME MK5 > (idx 117, type 4) > [17179586.644000] tveeprom 0-0050: TV standards PAL(B/G) PAL(I) > SECAM(L/L') PAL(D/D1/K) (eeprom 0x74) > [17179586.644000] tveeprom 0-0050: audio processor is MSP4418 (idx 25) > [17179586.644000] tveeprom 0-0050: decoder processor is SAA7115 (idx 19) > [17179586.644000] tveeprom 0-0050: has radio, has IR remote > [17179586.708000] eth1: register 'asix' at usb-0000:00:1d.7-3, ASIX > AX88772 USB 2.0 Ethernet, 00:30:4f:43:83:a7 > [17179586.708000] usbcore: registered new driver asix > [17179586.716000] tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) > [17179586.908000] tda9887 0-0043: chip found @ 0x86 (ivtv i2c driver #0) > [17179586.960000] saa7115 0-0021: saa7115 found @ 0x42 (ivtv i2c driver #0) > [17179587.156000] saa7127 0-0044: saa7129 found @ 0x88 (ivtv i2c driver #0) > [17179587.176000] msp3400 0-0040: MSP4418G-B3 found @ 0x80 (ivtv i2c > driver #0) > [17179587.176000] msp3400 0-0040: MSP4418G-B3 supports nicam and radio, > mode is autodetect and autoselect > [17179587.828000] ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) > [17179587.840000] ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) > [17179588.072000] ivtv0: Encoder revision: 0x02050032 > [17179588.080000] ivtv0: Decoder revision: 0x02020023 > [17179588.080000] ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 > buffers (4096KB total) > [17179588.080000] ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 > buffers (2048KB total) > [17179588.080000] ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 > buffers (2048KB total) > [17179588.080000] ivtv0: Allocate DMA encoder PCM audio stream: 455 x > 4608 buffers (2048KB total) > [17179588.080000] ivtv0: Create encoder radio stream > [17179588.080000] ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 > buffers (1024KB total) > [17179588.080000] ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 > buffers (1024KB total) > [17179588.080000] ivtv0: Create decoder VOUT stream > [17179588.080000] ivtv0: Allocate DMA decoder YUV stream: 20 x 51840 > buffers (1024KB total) > [17179588.160000] ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes) > [17179588.292000] tuner 0-0061: tuner type not set > [17179588.368000] tuner 0-0061: tuner type not set
The above 2 lines is your problem. You seem to have a unknown tuner type for the kernel. You can try and set it 38 in /etc/modprobe.conf by adding: options ivtv tuner=38 Now reload the ivtv module which should make the tv tuner work but the radio will probably not. Hans, a potential tester with a FM1216ME MK5 tuner in his PVR-350 :-) Greets Sander _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
