fwiw, i'm also getting the "chipmunk voices" problem on occasion.
Thanks! --Rob On Sat, Mar 24, 2007 at 04:12:27PM -0700, Rob Starling wrote: > Hi all! I have a PVR-150 (a real one) and it worked fine > until i moved to to another (older) computer. Now there is > some flicker (not a whole lot, but enough to be annoying) > in recordings (both from mythtv and from cat /dev/video0). > > I tried increasing increasing the latency_timer for my IDE > controller (setpci -v -s 00:11.1 latency_timer=80) as per > the advice at http://www.mythtv.org/wiki/index.php/PCI_Latency > but that didn't seem to help much. (default on my system is > 32, ivtv bumps the PVR-150 up to 64, so i set the IDE at 128) > > Does anybody have suggestions for settings i should poke at? > > My dmesg output follows, but appears normal. Also, i should > mention that the previous (working!) box was using almost > exactly the same kernel (2.6.18-3-k7 SMP) and was using > ivtv-0.10.0rc1. The current box is a little slower (1.4GHz > Athlon instead of 1.7GHz) and has an older motherboard. > ide0 isn't sharing an interrupt with anything, and ivtv0 is > sharing IRQ 5 with USB (not used) and my soundcard (also not > used during this test). > > Thanks! > --Rob > > ivtv: ==================== START INIT IVTV ==================== > ivtv: version 0.10.1 (tagged release) loading > ivtv: Linux version: 2.6.18-4-k7 SMP mod_unload K7 REGPARM gcc-4.1 > ivtv: In case of problems please include the debug info between > ivtv: the START INIT IVTV and END INIT IVTV lines, along with > ivtv: any module options, when mailing the ivtv-users mailinglist. > ivtv0: Autodetected Hauppauge card (cx23416 based) > ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKD] -> GSI 5 (level, low) -> > IRQ 5 > ivtv0: Unreasonably low latency timer, setting to 64 (was 32) > input: ImPS/2 Generic Wheel Mouse as /class/input/input2 > ts: Compaq touchscreen protocol output > ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) > ivtv0: Encoder revision: 0x02060039 > tveeprom 1-0050: Hauppauge model 26132, rev G1B2, serial# 9831694 > tveeprom 1-0050: tuner model is TCL M2523_5N_E (idx 112, type 50) > tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08) > tveeprom 1-0050: audio processor is CX25841 (idx 35) > tveeprom 1-0050: decoder processor is CX25841 (idx 28) > tveeprom 1-0050: has no radio, has IR remote > ivtv0: Autodetected Hauppauge WinTV PVR-150 > ivtv0: reopen i2c bus for IR-blaster support > tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) > cx25840 1-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0) > cx25840 1-0044: loaded v4l-cx25840.fw firmware (16382 bytes) > wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0) > ivtv0: Registered device video0 for encoder MPEG (4 MB) > ivtv0: Registered device video32 for encoder YUV (2 MB) > ivtv0: Registered device vbi0 for encoder VBI (1 MB) > ivtv0: Registered device video24 for encoder PCM audio (1 MB) > tuner 1-0061: type set to 50 (TCL 2002N) > ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 > ivtv: ==================== END INIT IVTV ==================== > ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKD] -> GSI 5 (level, low) -> > IRQ 5 _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
