I had a fuzzy line at the very top of my viewing window. It zig-zagged across the top of the screen and was very distracting etc. It went away when I selected the De-Interlace option in Mythtv.
Hope this helps Tony On Sun, 2007-04-15 at 17:38 +0200, Milijan MUDRINIC wrote: > Hi Everyone, > > i'm experiencing a minor issue when capturing streams from the composite > input. Overall I get good sound and pictures quality is ok although I can > notice a white vertical line scanning from left to right on my tv and I was > wondering if there was anything I could do to fix that. I tried the > different PAL standards without success. > > I've checked the source by plugging the composite cable directly in the TV > and it's fine. I've also played the mpg files on another PC and the problem > is still there so it's not a playback issue. > > Any help appreciated, > > Thanks. > Mil > > below are a few logs: > > v4l2-ctl --all > Driver info: > Driver name : ivtv > Card type : Hauppauge WinTV PVR-150 > Bus info : 0000:02:01.0 > Driver version: 2561 > Capabilities : 0x01070051 > Video Capture > VBI Capture > Sliced VBI Capture > Tuner > Audio > Radio > Read/Write > Format: > Type : Video Capture > Width/Height : 640/480 > Pixel Format : MPEG > Field : Interlaced > Bytes per Line: 0 > Size Image : 131072 > Colorspace : Broadcast NTSC/PAL (SMPTE170M/ITU601) > Format: > Type : Sliced VBI Capture > Service Set : > Service Line 0: / > Service Line 1: / > Service Line 2: / > Service Line 3: / > Service Line 4: / > Service Line 5: / > Service Line 6: / > Service Line 7: / > Service Line 8: / > Service Line 9: / > Service Line 10: / > Service Line 11: / > Service Line 12: / > Service Line 13: / > Service Line 14: / > Service Line 15: / > Service Line 16: / > Service Line 17: / > Service Line 18: / > Service Line 19: / > Service Line 20: / > Service Line 21: / > Service Line 22: / > Service Line 23: / > I/O Size : 0 > Format: > Type : VBI Capture > Sampling Rate : 27000000 Hz > Offset : 248 samples (9.18519e-06 secs after leading edge) > Samples per Line: 1440 > Sample Format : GREY > Start 1st Field : 6 > Count 1st Field : 18 > Start 2nd Field : 318 > Count 2nd Field : 18 > Video input : 2 (Composite 1) > Audio input : 1 (Line In 1) > Frequency: 6400 (400.000000 MHz) > Video standard = 0x0000000f > PAL-B/B1/G/H > Tuner: > Capabilities : 62.5 kHz multi-standard stereo lang1 lang2 > Frequency range : 44.0 MHz - 958.0 MHz > Signal strength : 99% > Current audio mode : lang1 > Available subchannels: mono lang2 > > > ivtv: no version for "struct_module" found: kernel tainted. > ivtv: ==================== START INIT IVTV ==================== > ivtv: version 0.10.1 (tagged release) loading > ivtv: Linux version: 2.6.20-1.2307.fc5 mod_unload 686 4KSTACKS > ivtv: In case of problems please include the debug info between > ivtv: the START INIT IVTV and END INIT IVTV lines, along with > ivtv: any module options, when mailing the ivtv-users mailinglist. > ivtv0: Autodetected Hauppauge card (cx23416 based) > ivtv0: Unreasonably low latency timer, setting to 64 (was 32) > ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) > ivtv0: Encoder revision: 0x02060039 > ivtv0: Autodetected Hauppauge WinTV PVR-150 > tuner 1-0043: chip found @ 0x86 (ivtv i2c driver #0) > tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) > cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0) > wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0) > ivtv0: Registered device video0 for encoder MPEG (4 MB) > ivtv0: Registered device video32 for encoder YUV (2 MB) > ivtv0: Registered device vbi0 for encoder VBI (1 MB) > ivtv0: Registered device video24 for encoder PCM audio (1 MB) > ivtv0: Registered device radio0 for encoder radio > ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 > ivtv: ==================== END INIT IVTV ==================== > ivtv0: Removed Hauppauge WinTV PVR-150, card #0 > ivtv: ==================== START INIT IVTV ==================== > ivtv: version 0.10.1 (tagged release) loading > ivtv: Linux version: 2.6.20-1.2307.fc5 mod_unload 686 4KSTACKS > ivtv: In case of problems please include the debug info between > ivtv: the START INIT IVTV and END INIT IVTV lines, along with > ivtv: any module options, when mailing the ivtv-users mailinglist. > ivtv0: Autodetected Hauppauge card (cx23416 based) > ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) > ivtv0: Encoder revision: 0x02060039 > ivtv0: Autodetected Hauppauge WinTV PVR-150 > tuner 1-0043: chip found @ 0x86 (ivtv i2c driver #0) > tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) > cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0) > wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0) > ivtv0: Registered device video0 for encoder MPEG (4 MB) > ivtv0: Registered device video32 for encoder YUV (2 MB) > ivtv0: Registered device vbi0 for encoder VBI (1 MB) > ivtv0: Registered device video24 for encoder PCM audio (1 MB) > ivtv0: Registered device radio0 for encoder radio > ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 > ivtv: ==================== END INIT IVTV ==================== > > _________________________________________________________________ > FREE pop-up blocking with the new MSN Toolbar - get it now! > http://toolbar.msn.click-url.com/go/onm00200415ave/direct/01/ > > > _______________________________________________ > ivtv-users mailing list > [EMAIL PROTECTED] > http://ivtvdriver.org/mailman/listinfo/ivtv-users _______________________________________________ ivtv-users mailing list [EMAIL PROTECTED] http://ivtvdriver.org/mailman/listinfo/ivtv-users
