Sanjay Darisi wrote: > >From your log, your device is registered as /dev/video0. So, try > mplayer /dev/video0 or try > > cat /dev/video0 | mplayer - > > > Sanjay. > > On 7/18/07, * Jerry Geis* <[EMAIL PROTECTED] > <mailto:[EMAIL PROTECTED]>> wrote: > > > I got a new PVR-150 and recompiled 2.6.21.1 <http://2.6.21.1> with > ivtv 0.10.4. > Things seemed to go OK. however when I do "mplayer /dev/video" it says > playing video but I never see a picture. > > Have I not done something? > > Jerry > > >
Sanjay, I tried mplayer /dev/video0 and had the same results no video. I tried cat /dev/video and cat /dev/video0 and I dont see anything on screen (I presume I should). I also noticed my fireware was not correct. So I download the lastest firmware and reboot. but the result was the same. here is my latest info: ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.10.4 (tagged release) loading ivtv: Linux version: 2.6.21.1 SMP mod_unload ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge card (cx23416 based) ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18 ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18 ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) ivtv0: Encoder revision: 0x02060039 tveeprom 0-0050: Hauppauge model 25012, rev C5A3, serial# 9957397 tveeprom 0-0050: tuner model is TCL MFNM05-4 (idx 103, type 43) tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 0-0050: audio processor is CX25843 (idx 37) tveeprom 0-0050: decoder processor is CX25843 (idx 30) tveeprom 0-0050: has radio, has no IR receiver, has no IR transmitter ivtv0: Autodetected Hauppauge WinTV PVR-150 tuner 0-0043: chip found @ 0x86 (ivtv i2c driver #0) tda9887 0-0043: tda988[5/6/7] found @ 0x43 (tuner) tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) ivtv0: Failed to load module cx25840 ivtv0: Failed to load module wm8775 ivtv0: Registered device video0 for encoder MPEG (4 MB) ivtv0: Registered device video32 for encoder YUV (2 MB) ivtv0: Registered device vbi0 for encoder VBI (1 MB) ivtv0: Registered device video24 for encoder PCM audio (1 MB) ivtv0: Registered device radio0 for encoder radio tuner 0-0061: type set to 43 (Philips NTSC MK3 (FM1236MK3 or FM1236/F)) ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! ivtv0: i2c addr 0x44 not found for command 0x4008646f! ivtv0: i2c hardware 0x00000020 (wm8775) not found for command 0x4008646d! ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0x4008646d! ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ivtv: ==================== END INIT IVTV ==================== _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
