Jerry Geis wrote: > Sanjay Darisi wrote: >> >From your log, your device is registered as /dev/video0. So, try >> mplayer /dev/video0 or try >> >> cat /dev/video0 | mplayer - >> >> >> Sanjay. >> >> On 7/18/07, * Jerry Geis* <[EMAIL PROTECTED] >> <mailto:[EMAIL PROTECTED]>> wrote: >> >> >> I got a new PVR-150 and recompiled 2.6.21.1 <http://2.6.21.1> with >> ivtv 0.10.4. >> Things seemed to go OK. however when I do "mplayer /dev/video" it >> says >> playing video but I never see a picture. >> >> Have I not done something? >> >> Jerry >> >> >> > > > Sanjay, > > I tried mplayer /dev/video0 and had the same results no video. > I tried cat /dev/video and cat /dev/video0 and I dont see anything on > screen (I presume I should). > > I also noticed my fireware was not correct. So I download the lastest > firmware and > reboot. but the result was the same. > > here is my latest info: > > ivtv: ==================== START INIT IVTV ==================== > ivtv: version 0.10.4 (tagged release) loading > ivtv: Linux version: 2.6.21.1 SMP mod_unload ivtv: In case of problems > please include the debug info between > ivtv: the START INIT IVTV and END INIT IVTV lines, along with > ivtv: any module options, when mailing the ivtv-users mailinglist. > ivtv0: Autodetected Hauppauge card (cx23416 based) > ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18 > ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [APC3] -> GSI 18 (level, > low) -> IRQ 18 > ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) > ivtv0: Encoder revision: 0x02060039 > tveeprom 0-0050: Hauppauge model 25012, rev C5A3, serial# 9957397 > tveeprom 0-0050: tuner model is TCL MFNM05-4 (idx 103, type 43) > tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08) > tveeprom 0-0050: audio processor is CX25843 (idx 37) > tveeprom 0-0050: decoder processor is CX25843 (idx 30) > tveeprom 0-0050: has radio, has no IR receiver, has no IR transmitter > ivtv0: Autodetected Hauppauge WinTV PVR-150 > tuner 0-0043: chip found @ 0x86 (ivtv i2c driver #0) > tda9887 0-0043: tda988[5/6/7] found @ 0x43 (tuner) > tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) > ivtv0: Failed to load module cx25840 > ivtv0: Failed to load module wm8775 > ivtv0: Registered device video0 for encoder MPEG (4 MB) > ivtv0: Registered device video32 for encoder YUV (2 MB) > ivtv0: Registered device vbi0 for encoder VBI (1 MB) > ivtv0: Registered device video24 for encoder PCM audio (1 MB) > ivtv0: Registered device radio0 for encoder radio > tuner 0-0061: type set to 43 (Philips NTSC MK3 (FM1236MK3 or FM1236/F)) > ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! > ivtv0: i2c addr 0x44 not found for command 0x4008646f! > ivtv0: i2c hardware 0x00000020 (wm8775) not found for command 0x4008646d! > ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0x4008646d! > ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! > ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! > ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c! > ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 > ivtv: ==================== END INIT IVTV ==================== > > > >
Additional information: This line is in dmesg after typing mplayer /dev/video ivtv0: i2c addr 0x44 not found for command 0xc0d05605! jerry _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
