> > cx18-0 info: NTSC tuner detected > > cx18-0: DVB & VBI are not yet supported > > cx18-0 info: Loaded module tuner > > cx18-0 info: Loaded module cs5345 > > cx18-0 i2c: i2c client register > > cx18-0 i2c: i2c client register > > cs5345 0-004c: chip found @ 0x98 (cx18 i2c driver #0-0) > > cx18-0 info: Allocate encoder MPEG stream: 63 x 32768 buffers (2016kB total) > > cx18-0 info: Allocate TS stream: 32 x 32768 buffers (1024kB total) > > cx18-0 info: Allocate encoder YUV stream: 16 x 131072 buffers (2048kB total) > > cx18-0 info: Allocate encoder PCM audio stream: 63 x 16384 buffers (1008kB > total) > > cx18-0: Disabled encoder IDX device > > videodev: "" has no release callback. Please fix your driver for proper > > sysfs > support, see http://lwn.net/Articles/36850/ > > I have to look into this. I doesn't look like anything to worry about > right now. > > > cx18-0: Registered device video0 for encoder MPEG (2 MB) > > DVB: registering new adapter (cx18). > > MXL5005S: Attached at address 0x63 > > DVB: registering frontend 0 (Samsung S5H1409 QAM/8VSB Frontend)... > > cx18-0: DVB Frontend registered > > videodev: "" has no release callback. Please fix your driver for proper > > sysfs > support, see http://lwn.net/Articles/36850/ > > cx18-0: Registered device video32 for encoder YUV (2 MB) > > videodev: "" has no release callback. Please fix your driver for proper > > sysfs > support, see http://lwn.net/Articles/36850/ > > cx18-0: Registered device video24 for encoder PCM audio (1 MB) > > videodev: "" has no release callback. Please fix your driver for proper > > sysfs > support, see http://lwn.net/Articles/36850/ > > cx18-0: Registered device radio-64 for encoder radio > > cx18-0 info: load segment a00000-a07fff > > cx18-0 info: load segment ae0000-ae00ff > > cx18-0 info: load segment b00000-b1a65f > > cx18-0: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes) > > cx18-0: loaded v4l-cx23418-cpu.fw firmware (174716 bytes) > > cx18-0 info: load segment a00000-a07fff > > cx18-0 info: load segment ae0000-ae00ff > > cx18-0 info: load segment b00000-b1a65f > > cx18-0: Could not start the CPU > > This is a problem for you. > > You can try this: > > 1. Find the "#if 0" on line 347 of > linux/drivers/media/video/cx18/cx18-firmware.c in the function > cx18_firmware_init() and change it to "#if 1". > > 2. recompile and reinstall the cx18 driver > > 3. unload and reload the newly built cx18 module >
Well, after I recompiled everything, heres the dmesg. Most of the previous errors are gone, however I can't seem to find any program that can play it. (And might I add, there are very few TV viewing programs that I've found. Very few. cx18: Start initialization, version 1.0.0 cx18-0: Initializing card #0 cx18-0: Autodetected Hauppauge card cx18-0: cx23418 revision 01010000 (B) tveeprom 0-0050: Encountered bad packet header [00]. Corrupt or not a Hauppauge eeprom. cx18-0: Invalid EEPROM cx18-0: DVB & VBI are not yet supported cs5345 0-004c: chip found @ 0x98 (cx18 i2c driver #0-0) cx18-0: Disabled encoder IDX device videodev: "" has no release callback. Please fix your driver for proper sysfs support, see http://lwn.net/Articles/36850/ cx18-0: Registered device video0 for encoder MPEG (2 MB) DVB: registering new adapter (cx18). MXL5005S: Attached at address 0x63 DVB: registering frontend 0 (Samsung S5H1409 QAM/8VSB Frontend)... cx18-0: DVB Frontend registered videodev: "" has no release callback. Please fix your driver for proper sysfs support, see http://lwn.net/Articles/36850/ cx18-0: Registered device video32 for encoder YUV (2 MB) videodev: "" has no release callback. Please fix your driver for proper sysfs support, see http://lwn.net/Articles/36850/ cx18-0: Registered device video24 for encoder PCM audio (1 MB) videodev: "" has no release callback. Please fix your driver for proper sysfs support, see http://lwn.net/Articles/36850/ cx18-0: Registered device radio-64 for encoder radio cx18-0: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes) cx18-0: loaded v4l-cx23418-cpu.fw firmware (174716 bytes) cx18-0: loaded v4l-cx23418-dig.fw firmware (16382 bytes) cx18-0: Initialized card #0: Hauppauge HVR-1600 cx18: End initialization And unlike in the past, it was only run once, not the 3 times it was in the past. Thanks! ____________________________________________________________________________________ Be a better friend, newshound, and know-it-all with Yahoo! Mobile. Try it now. http://mobile.yahoo.com/;_ylt=Ahu06i62sR8HDtDypao8Wcj9tAcJ _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
