paul stark wrote:
Hi,
I'm running gentoo with kernel 2.6.25-gentoo-r4 and cannot sem to get
the PVR-250 card to work with mythtv. The tuner, saa7115 and msp3400
kernel modules are not loading for some reason. I've tried googling
the error but haven't found anything similar. I was wondering if
anyone has come across a similar issue or if there are additional
diagnostics I can run to help narrow down the failure? I've attached
a copy of my dmesg output.
Thanks,
Paul
ivtv: Start initialization, version 1.2.0
ivtv0: Initializing card #0
ivtv0: Autodetected Hauppauge card (cx23415 based)
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 19
ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [LNKB] -> GSI 19 (level,
low) -> IRQ 19
tveeprom 0-0050: Hauppauge model 48432, rev I110, serial# 6145626
tveeprom 0-0050: tuner model is Philips FI1236 MK2 (idx 10, type 2)
tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 0-0050: audio processor is MSP4448 (idx 27)
tveeprom 0-0050: decoder processor is SAA7115 (idx 19)
tveeprom 0-0050: has no radio, has no IR receiver, has no IR transmitter
ivtv0: Autodetected Hauppauge WinTV PVR-250
ivtv0: Failed to load module tuner
ivtv0: Failed to load module saa7115
ivtv0: Failed to load module msp3400
ivtv0: Registered device video0 for encoder MPG (4096 kB)
ivtv0: Registered device video32 for encoder YUV (2048 kB)
ivtv0: Registered device vbi0 for encoder VBI (1024 kB)
ivtv0: Registered device video24 for encoder PCM (320 kB)
ivtv0: Initialized card #0: Hauppauge WinTV PVR-250
ivtv: End initialization
cx23885 driver version 0.0.1 loaded
ACPI: PCI Interrupt Link [LNEA] enabled at IRQ 17
ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LNEA] -> GSI 17 (level,
low) -> IRQ 17
CORE cx23885[0]: subsystem: 0070:7911, board: Hauppauge WinTV-HVR1250
[card=3,autodetected]
cx23885[0]: i2c bus 0 registered
tuner' 2-0043: chip found @ 0x86 (cx23885[0])
tda9887 2-0043: tda988[5/6/7] found
cx23885[0]: i2c bus 1 registered
msp3400' 3-0044: MSP7468D-4 found @ 0x88 (cx23885[0])
msp3400' 3-0044: MSP7468D-4 mode is autodetect
cx23885[0]: i2c bus 2 registered
tveeprom 1-0050: Encountered bad packet header [ff]. Corrupt or not a
Hauppauge eeprom.
cx23885[0]: warning: unknown hauppauge model #0
cx23885[0]: hauppauge eeprom: model=0
cx23885[0]: cx23885 based dvb card
MT2131: successfully identified at address 0x61
DVB: registering new adapter (cx23885[0])
DVB: registering frontend 0 (Samsung S5H1409 QAM/8VSB Frontend)...
cx23885_dev_checkrevision() Hardware revision = 0xc0
cx23885[0]/0: found at 0000:03:00.0, rev: 3, irq: 17, latency: 0,
mmio: 0xfea00000
PCI: Setting latency timer of device 0000:03:00.0 to 64
Adding 506036k swap on /dev/sdb2. Priority:-1 extents:1 across:506036k
r8169: eth0: link up
eth0: no IPv6 routers present
ivtv0: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
ivtv0: Loaded v4l-cx2341x-dec.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02060039
ivtv0: Decoder revision: 0x02020023
ivtv0: i2c addr 0x21 not found for command 0x4008646f
ivtv0: i2c hardware 0x00000008 (msp3400) not found for command 0x4008646d
Hi Paul,
Are you absolutely that your kernel has those modules and/or are they
modules?
$ find /lib/modules/`uname -r` -name 'tuner*'
/lib/modules/2.6.24-etchnhalf.1-amd64/kernel/drivers/media/video/tuner.ko
/lib/modules/2.6.24-etchnhalf.1-amd64/kernel/drivers/media/video/tuner-simple.ko
/lib/modules/2.6.24-etchnhalf.1-amd64/kernel/drivers/media/video/tuner-3036.ko
$ find /lib/modules/`uname -r` -name 'msp3400*'
/lib/modules/2.6.24-etchnhalf.1-amd64/kernel/drivers/media/video/msp3400.ko
$ vi /boot/config-`uname -r`
#
# Multimedia devices
#
CONFIG_VIDEO_DEV=m
CONFIG_VIDEO_V4L1=y
CONFIG_VIDEO_V4L1_COMPAT=y
CONFIG_VIDEO_V4L2=y
CONFIG_VIDEO_CAPTURE_DRIVERS=y
# CONFIG_VIDEO_ADV_DEBUG is not set
CONFIG_VIDEO_HELPER_CHIPS_AUTO=y
CONFIG_VIDEO_TVAUDIO=m
CONFIG_VIDEO_TDA7432=m
CONFIG_VIDEO_TDA9840=m
CONFIG_VIDEO_TDA9875=m
CONFIG_VIDEO_TEA6415C=m
CONFIG_VIDEO_TEA6420=m
CONFIG_VIDEO_MSP3400=m
CONFIG_VIDEO_CS53L32A=m
CONFIG_VIDEO_WM8775=m
CONFIG_VIDEO_WM8739=m
.
.
and so on
.
.
A place to start...
If you find that you don't have those modules, then you
will need to update the kernel config to make your video
devices modules and rebuild your kernel. Or go back to
the source and ask them to make a kernel with your devices
enabled as modules.
begin:vcard
fn:Mark Paulus
n:Paulus;Mark
org:MCI;Lec Interfaces / 40419
adr;dom:;;2424 Garden of the Gods Rd;Colorado Springs;CO;80919
email;internet:[EMAIL PROTECTED]
title:Mark Paulus
tel;work:719-535-5578
tel;pager:800-pagemci / 1406052
tel;home:v622-5578
version:2.1
end:vcard
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
