2011. 06. 29, szerda keltezéssel 13.15-kor Federico Allegretti ezt írta: > Hello. > > I'm trying to install ivtv drivers on an old AMD Duron 650 machine to > drive a pvr350 like a video playback server. > > Installed in a mirror hd enviroment a debian 6.02 and everything seems > ok. > > "lspci" reports: > 00:08.0 Multimedia video controller: Internext Compression Inc iTVC15 > MPEG-2 Encoder (rev 01) > > "dmesg | grep ivtv" reports: > [ 9.434856] ivtv: Start initialization, version 1.4.1 > [ 9.435234] ivtv0: Initializing card 0 > [ 9.435250] ivtv0: Autodetected Hauppauge card (cx23415 based) > [ 9.436766] ivtv 0000:00:08.0: PCI INT A -> Link[LNKA] -> GSI 10 > (level, low) -> IRQ 10 > [ 9.436790] ivtv0: Unreasonably low latency timer, setting to 64 > (was 32) > [ 9.494359] ivtv0: Autodetected Hauppauge WinTV PVR-350 > [ 9.630465] saa7115 1-0021: saa7115 found (1f7115d0e100000) @ 0x42 > (ivtv i2c driver #0) > [ 9.791591] saa7127 1-0044: saa7129 found @ 0x88 (ivtv i2c driver > #0) > [ 9.872948] msp3400 1-0040: MSP4418G-B3 found @ 0x80 (ivtv i2c > driver #0) > [ 9.989589] tuner 1-0043: chip found @ 0x86 (ivtv i2c driver #0) > [ 10.008795] tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) > [ 10.067504] IRQ 10/ivtv0: IRQF_DISABLED is not guaranteed on shared > IRQs > [ 10.069283] ivtv0: Registered device video0 for encoder MPG (4096 > kB) > [ 10.069666] ivtv0: Registered device video32 for encoder YUV (2048 > kB) > [ 10.069992] ivtv0: Registered device vbi0 for encoder VBI (1024 kB) > [ 10.070340] ivtv0: Registered device video24 for encoder PCM (320 > kB) > [ 10.070662] ivtv0: Registered device radio0 for encoder radio > [ 10.070970] ivtv0: Registered device video16 for decoder MPG (1024 > kB) > [ 10.071284] ivtv0: Registered device vbi8 for decoder VBI (64 kB) > [ 10.071638] ivtv0: Registered device vbi16 for decoder VOUT > [ 10.071963] ivtv0: Registered device video48 for decoder YUV (1024 > kB) > [ 10.071976] ivtv0: Initialized card: Hauppauge WinTV PVR-350 > [ 10.074597] ivtv: End initialization > [ 10.740092] ivtv 0000:00:08.0: firmware: requesting > v4l-cx2341x-enc.fw > [ 10.782961] ivtv0: Unable to open firmware v4l-cx2341x-enc.fw (must > be 376836 bytes) > [ 10.783033] ivtv0: Did you put the firmware in the hotplug firmware > directory? > [ 10.783094] ivtv0: Retry loading firmware > [ 11.404091] ivtv 0000:00:08.0: firmware: requesting > v4l-cx2341x-enc.fw > [ 11.412921] ivtv0: Unable to open firmware v4l-cx2341x-enc.fw (must > be 376836 bytes) > [ 11.412996] ivtv0: Did you put the firmware in the hotplug firmware > directory? > [ 11.413060] ivtv0: Failed to initialize on minor 2 > [ 11.413768] ivtv0: Failed to initialize on minor 0 > [ 11.415383] ivtv0: Failed to initialize on minor 4 > [ 11.416696] ivtv0: Failed to initialize on minor 5 > [ 11.417907] ivtv0: Failed to initialize on minor 6 > [ 11.419120] ivtv0: Failed to initialize on minor 7 > [ 11.420495] ivtv0: Failed to initialize on minor 1 > [ 11.421717] ivtv0: Failed to initialize on minor 3 > [ 11.422929] ivtv0: Failed to initialize on minor 8 > > Now i suppose i need to download firmware files and put them in the > correct folder, BUT i cannot found correct firmware AND cannot find an > "HOTPLUG" directory :( > > Tryied to get firmware from there: > http://dl.ivtvdriver.org/ivtv/firmware/ivtv-firmware.tar.gz > BUT "tar xvf ivtv-firmware.tar.gz" reports an invalid tar file > (italian language distro): > tar: Questo non sembra un archivio tar > tar: Passaggio alla prossima intestazione > tar: Uscita con stato di fallimento in base agli errori precedenti > > ALL other firwares in the http://dl.ivtvdriver.org/ivtv/firmware/ > folder seems to be corrupted (except cx18...) and also "tar xvf > xf86-video-ivtv-1.1.2.tar.gz" (downloaded from > http://dl.ivtvdriver.org/xf86-video-ivtv/ ) fire's the tar error for > NOT a tar file. > > "tar xvf ivtv-1.2.0.tar.gz" on archive downloaded from > http://dl.ivtvdriver.org/ivtv/stable/ > goes well, but "make" gives: > make[2]: Entering directory `/lib/modules/2.6.32-5-686/build' > make[2]: *** No rule to make target `modules'. Stop. > make[2]: Leaving directory `/lib/modules/2.6.32-5-686/build' > make[1]: *** [all] Error 2 > make[1]: Leaving directory `/home/playback/ivtv-1.2.0/i2c-drivers' > make: *** [all] Error 2 > > now i really don't know what to do :( > > Help please :D any hint will be welcomed > > Federico
Please install "firmware-ivtv" from the non-free section of Debian, it will take care of everything needed to load the firmware. You do not need to compile itv-1.2.0.tar.gz. And as you've got a PVR-350, the "xserver-xorg-video-ivtv" is maybe also of interest for you. Levente _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
