> >Dec 8 01:57:41 r2d2 kernel: saa7115: status: 0xc0 > >Dec 8 01:57:41 r2d2 kernel: saa7115: decoder disable output > >Dec 8 01:57:41 r2d2 kernel: ivtv: i2c client addr: 0x61 not found! > >Dec 8 01:57:41 r2d2 kernel: saa7115: decoder enable output > > > That simply means that your tuner module is not loaded. Note that the > tuner module does *not* ship with the ivtv driver. We use the tuner > module from your kernel. You can build the tuner driver by selecting > the BTTV, CX88, or SAA7134 driver in your kernel build options.
Thanks. This I didn't fully understand. I thought all the time that the tuner was compilled into the ivtv module. Which tuner module should I use? For the above I used the tuner-3036. I compilled the plain "tuner" module and modprobed it and then ivtv. Now it appears much better, but I can't tune any channels. Dec 9 00:15:50 r2d2 kernel: ivtv: Setting Tuner 38 Dec 9 00:15:50 r2d2 kernel: tuner: type already set (38) Dec 9 00:15:50 r2d2 kernel: saa7115: decoder set input (4) Dec 9 00:15:50 r2d2 kernel: saa7115: now setting Composite input Dec 9 00:15:50 r2d2 kernel: ivtv: Setting audio matrix to input 3, output 1 Dec 9 00:15:50 r2d2 kernel: ivtv: Switching standard to PAL. Dec 9 00:15:50 r2d2 kernel: ivtv: ivtv_enc_thread: pid = 3647, itv = 0xcecc8fa0 Dec 9 00:15:50 r2d2 kernel: ivtv: ivtv_dec_thread: pid = 3648, itv = 0xcecc8fa0 Dec 9 00:15:50 r2d2 kernel: saa7115: decoder set norm PAL Dec 9 00:15:50 r2d2 kernel: saa7115: set audio: 0x01 Dec 9 00:15:50 r2d2 kernel: saa7127: Setting Encoder Video Standard Dec 9 00:15:50 r2d2 kernel: saa7127: Set PAL Video Mode Dec 9 00:15:50 r2d2 kernel: saa7127: Selecting PAL video Standard Dec 9 00:15:50 r2d2 kernel: ivtv: Initialized WinTV PVR 350, card #0 Dec 9 00:15:50 r2d2 kernel: ivtv: ==================== END INIT IVTV ==================== Dec 9 00:15:51 r2d2 kernel: lirc_dev: IR Remote Control driver registered, at major 61 Dec 9 00:15:51 r2d2 kernel: lirc_i2c: chip found @ 0x18 (Hauppauge IR) Dec 9 00:15:51 r2d2 kernel: ivtv: i2c attach [client=Hauppauge IR,ok] Dec 9 00:15:51 r2d2 kernel: lirc_dev: lirc_register_plugin:sample_rate: 10 Dec 9 00:16:16 r2d2 kernel: saa7115: status: 0xc0 Dec 9 00:16:21 r2d2 kernel: saa7115: decoder set picture bright=128 contrast=64 saturation=64 hue=0 Dec 9 00:16:21 r2d2 last message repeated 3 times Dec 9 00:16:21 r2d2 kernel: saa7115: decoder disable output Dec 9 00:16:21 r2d2 kernel: saa7115: decoder set input (0) Dec 9 00:16:21 r2d2 kernel: saa7115: now setting Composite input Dec 9 00:16:21 r2d2 kernel: ivtv: Setting audio matrix to input 1, output 1 Dec 9 00:16:21 r2d2 kernel: saa7115: decoder enable output Dec 9 00:16:21 r2d2 kernel: ivtv: Switching standard to NTSC. Dec 9 00:16:21 r2d2 kernel: saa7115: decoder set norm NTSC Dec 9 00:16:21 r2d2 kernel: saa7115: set audio: 0x01 Dec 9 00:16:21 r2d2 kernel: saa7127: Setting Encoder Video Standard Dec 9 00:16:21 r2d2 kernel: saa7127: Set NTSC Video Mode Dec 9 00:16:21 r2d2 kernel: saa7127: Selecting NTSC video Standard Dec 9 00:16:21 r2d2 kernel: saa7115: decoder disable output Dec 9 00:16:21 r2d2 kernel: tuner: TV freq (0.00) out of range (44-958) Dec 9 00:16:22 r2d2 kernel: saa7115: decoder enable output Dec 9 00:16:22 r2d2 kernel: ivtv: Switching standard to PAL. Dec 9 00:16:22 r2d2 kernel: saa7115: decoder set norm PAL Dec 9 00:16:22 r2d2 kernel: saa7115: set audio: 0x01 Dec 9 00:16:22 r2d2 kernel: saa7127: Setting Encoder Video Standard Dec 9 00:16:22 r2d2 kernel: saa7127: Set PAL Video Mode Dec 9 00:16:22 r2d2 kernel: saa7127: Selecting PAL video Standard Dec 9 00:16:22 r2d2 kernel: saa7115: status: 0xc0 Dec 9 00:16:22 r2d2 kernel: saa7115: decoder disable output Dec 9 00:16:22 r2d2 kernel: saa7115: decoder enable output : ; ..the three last lines repeated for each scan... Here's some info: [EMAIL PROTECTED]:/ # more /etc/mythtv/modules/ivtv alias char-major-81 videodev alias char-major-61 lirc_i2c options ivtv ivtv_debug=1 tuner=38 options tuner type=38 options saa7127 enable_output=1 output_select=0 options msp3400 once=1 simple=1 add below ivtv msp3400 saa7115 tuner add above ivtv lirc_dev lirc_i2c post-install ivtv /usr/local/bin/test_ioctl -d /dev/video0 -u 0x00ff alias char-major-81-0 ivtv [EMAIL PROTECTED]:/usr/src/ivtv-0.3.1x/utils # ./ivtvctl -I check SAA7115 input signal ioctl: VIDEO_STATUS = Bad SAA7115 reg[STATUS#1 - 0x1E] = 50 Color Standard (D0-D1): BW/No color White peak loop (D2): Not activated Gain value for act.lum. (min) (D3): Not limited Gain value for act.lum. (max) (D4): Limited WIPA-mode slow-time constant (D5): Not activated Horizontal frequency (D6): Unlocked Field length (D7): Non-standard SAA7115 reg[STATUS#2 - 0x1F] = c0 Ready for capture (D0): No Macrovision 7.01 (D1): No MV Colorstripe burst (D2): No MV Colorstripe burst type 3 (D3): No Input signal timebase (D4): Non-stable (VCR) Field frequency (D5): 50Hz H & V loops (D6): Unlocked Interlace (D7): Detected Also, still no response from the remote. Any ideas? -Frode -- ^ Frode Tennebø | email: [EMAIL PROTECTED] | [EMAIL PROTECTED] ^ | with Standard.Disclaimer; use Standard.Disclaimer; | ------------------------------------------------------- SF email is sponsored by - The IT Product Guide Read honest & candid reviews on hundreds of IT Products from real users. Discover which products truly live up to the hype. Start reading now. http://productguide.itmanagersjournal.com/ _______________________________________________ Ivtv-users mailing list [EMAIL PROTECTED] https://lists.sourceforge.net/lists/listinfo/ivtv-users
