Hi Chris,
Add the line:
alias tveeprom tveeprom-ivtv
to your /etc/modprobe.conf file after the ivtv aliases and it will load
the tveeprom-ivtv instead of tveeprom and you will not get the error
messages:
Best regards
Niels Dybdahl
-----Original Message-----
From: Chris [mailto:[EMAIL PROTECTED]
Sent: 27. januar 2005 01:53
To: IVTV Group
Subject: [Ivtv-users] ivtv module loads, plays snow
this system is an asus kt600, xp1700, radeon aiw8500dv, running fc3.
this setup works properly in windows. the pvr-250 is in the first pci
slot for dma, but i have tried others. radeon driver is the most recent
ati proprietay driver: fglrx_6_8_0-8.8.25-1.i386. it built and installed
no problem, glxgears works. kernel is 2.6.10-1.737_FC3, i have also
tried 2.6.9-1.724_FC3. the module will build and insert successfully. i
have also tried v1.1 installed from apt, as in this howto:
http://wilsonet.com/mythtv/fcmyth.php , with the same result - snow.
/dev/video0 exists. i can cat from it to mplayer resulting in snow. i
can cat from it to the console, resulting in (haha) ascii snow. i can
cat from it to an .mpg file, which plays back as snow. i have used
ivtvctl to make sure i'm using ntsc, and tried using pitune to flip
channels and inputs while cat'ing video to mplayer - more snow.
tvtime says "cannot open capture device /dev/video0" and spits this at
the console:
videoinput: Card failed to allocate capture buffers
i tried this:
echo 16384 > /proc/sys/vm/min_free_kbytes
but it didn't help.
any related experiance, or suggestions would be appreciated. thx in
advance
dmesg output from apt package of ivtv 1.1:
Linux video capture interface: v1.00
ivtv: no version for "struct_module" found: kernel tainted.
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.1.10 (0.1.10-49.1_pre2_ck100zz.rhfc3.at) loading
ivtv: Linux version: 2.6.10-1.737_FC3 686 REGPARM 4KSTACKS gcc-3.4
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: Autodetected WinTV PVR 250 card
ivtv: Found an iTVC16 based chip
ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 9 (level, low) -> IRQ 9
ivtv: Unreasonably low latency timer, setting to 64 (was 32)
ivtv: pci: VIA detected device: 0x3189 vendor: 0x1106
ivtv: i2c client addr: 0x50 not found!
ivtv: Error -19 reading Hauppauge eeprom.
ivtv: Possible causes: the tveeprom module was not loaded, or
ivtv: the eeprom kernel module was loaded before the tveeprom module.
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv: i2c attach [client=(tuner unset),ok]
saa7115: Ignoring new-style parameters in presence of obsolete ones
saa7115: starting probe for adapter SMBus Via Pro adapter at e800 (0x0)
saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
saa7115: detecting saa7115 client on address 0x42
saa7115: writing init values
ivtv: i2c attach [client=saa7115[0],ok]
saa7115: status: (1E) 0x48, (1F) 0xc0
msp34xx: init: chip=MSP3445G-B8 +nicam +simple +simpler +radio
mode=simple
ivtv: i2c attach [client=MSP3445G-B8,ok]
msp3410: daemon started
ivtv: Encoder revision: 0x02040024
ivtv: Configuring WinTV PVR 250 card with 4 streams
ivtv: Create DMA stream 0 using 128 buffers of size 32768
ivtv: Create DMA stream 1 using 128 buffers of size 32768
ivtv: Create stream 2 using 128 buffers of size 52224
ivtv: Create DMA stream 3 using 128 buffers of size 32768
ivtv: Could not detect tuner standard, defaulting to NTSC.
ivtv: Setting audio matrix to input 3, output 1
ivtv: Switching standard to NTSC.
tuner: tuner type not set
saa7115: decoder set norm NTSC
saa7115: set audio: 0x01
ivtv: Initialized WinTV PVR 250, card #0
ivtv: ==================== END INIT IVTV ====================
hald: page allocation failure. order:5, mode:0xd0
[<c014150a>] __alloc_pages+0x281/0x28e
[<c014152f>] __get_free_pages+0x18/0x24
[<e5382d1e>] ivtv_init_buffer+0x49/0xa4 [ivtv]
[<e5382d90>] ivtv_init_queue_nolock+0x17/0x61 [ivtv] [<e5382dfa>]
ivtv_init_queues_nolock+0x20/0x39 [ivtv] [<e5386e87>]
ivtv_stream_alloc+0x77/0xad [ivtv] [<e53865cb>]
ivtv_v4l2_open+0x2c8/0x3a6 [ivtv] [<e0cc416a>] video_open+0xd4/0x14e
[videodev] [<c0167765>] chrdev_open+0x28e/0x2a4 [<c015d10a>]
dentry_open+0xbd/0x180 [<c015d047>] filp_open+0x36/0x3c [<c016816f>]
sys_lstat64+0x1e/0x23 [<c01d3f88>] strncpy_from_user+0x37/0x56
[<c015d511>] sys_open+0x31/0x7d [<c0103337>] syscall_call+0x7/0xb
ivtv: No memory on buffer alloc!
ivtv: Buffer alloc failed!
dmesg from ivtv 2.0rc3 built from source:
Linux video capture interface: v1.00
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.2.0 (rc3e) loading
ivtv: Linux version: 2.6.10-1.737_FC3 686 REGPARM 4KSTACKS gcc-3.4
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: Autodetected WinTV PVR 250 card
ivtv: Found an iTVC16 based chip
ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 9 (level, low) -> IRQ 9
ivtv: VIA PCI device: 0x3189 vendor: 0x1106
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv: i2c attach [client=(tuner unset),ok]
saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
saa7115: detecting saa7115 client on address 0x42
saa7115: writing init values
ivtv: i2c attach [client=saa7115[1],ok]
saa7115: status: (1E) 0x48, (1F) 0xc0
msp34xx: init: chip=MSP3445G-B8 +nicam +simple +simpler +radio
mode=simple
ivtv: i2c attach [client=MSP3445G-B8,ok]
msp3410: daemon started
ivtv: i2c client addr: 0x50 not found!
ivtv: Error -19 reading Hauppauge eeprom.
ivtv: Possible causes: the tveeprom module was not loaded, or
ivtv: the eeprom kernel module was loaded before the tveeprom module.
ivtv: Encoder revision: 0x02040024
ivtv: Encoder Firmware is buggy, use version 0x02040011
ivtv: Configuring WinTV PVR 250 card with 4 streams
ivtv: Create DMA stream 0 using 256 16384 byte buffers 4194304 kbytes
total
ivtv: Registered v4l2 device, streamtype 0 minor 0
ivtv: Create DMA stream 1
ivtv: Registered v4l2 device, streamtype 1 minor 32
ivtv: Create stream 2 using 40 52224 byte buffers 2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 2 minor 224
ivtv: Create DMA stream 3 using 455 4608 byte buffers 2097152 kbytes
total
ivtv: Registered v4l2 device, streamtype 3 minor 24
ivtv: Could not detect tuner standard, defaulting to NTSC.
ivtv: Setting audio matrix to input 3, output 1
ivtv: Switching standard to NTSC.
tuner: tuner type not set
saa7115: decoder set norm NTSC
saa7115: set audio: 0x01
ivtv: Initialized WinTV PVR 250, card #0
ivtv: ==================== END INIT IVTV ====================
ivtv: ivtv_enc_thread: pid = 10696, itv = 0xe553a5a0
-------------------------------------------------------
This SF.Net email is sponsored by: IntelliVIEW -- Interactive Reporting
Tool for open source databases. Create drag-&-drop reports. Save time by
over 75%! Publish reports on the web. Export to DOC, XLS, RTF, etc.
Download a FREE copy at http://www.intelliview.com/go/osdn_nl
_______________________________________________
Ivtv-users mailing list
Ivtv-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/ivtv-users
-------------------------------------------------------
This SF.Net email is sponsored by: IntelliVIEW -- Interactive Reporting
Tool for open source databases. Create drag-&-drop reports. Save time
by over 75%! Publish reports on the web. Export to DOC, XLS, RTF, etc.
Download a FREE copy at http://www.intelliview.com/go/osdn_nl
_______________________________________________
Ivtv-users mailing list
Ivtv-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/ivtv-users
