Hi Kiste, Thank you very much. That solved the baudrate issue.
But serial_hardware still don't work as it should. Still have Frame and Break error on PC side. Now, your code; forever loop serial_hw_data=0x22 serial_hw_data=0x22 delay_1s(1) end loop Results; b7 37 00 ·7. b7 37 00 ·7. b7 37 00 ·7. b7 37 00 ·7. b7 37 00 ·7. b7 37 00 ·7. b7 37 00 ·7. b7 37 00 ·7. b7 37 00 ·7. b7 37 00 ·7. b7 37 00 ·7. b7 37 00 ·7. b7 37 00 ·7. b7 37 00 ·7. b7 37 00 ·7. b7 37 00 ·7. b7 37 00 ·7. b7 37 00 ·7. b7 37 00 ·7. b7 37 00 ·7. b7 37 00 ·7. b7 37 00 ·7. b7 37 00 ·7. b7 37 00 ·7. b7 37 00 ·7. b7 37 00 ·7. Cannot understand what's going on. Anymore ideas? Cheers, Filipe Santos. On Tuesday, May 17, 2022 at 8:34:17 PM UTC+1 Kiste wrote: > So, here it is: > > pragma target clock 20_000_000 -- oscillator frequency > pragma target RSTOSC HFINT32 -- power-up clock select: > OSC > > You're telling the compiler, the PIC would run at 20MHz, and you're > setting the PIC to 32MHz. > > Make it > > pragma target clock 32_000_000 -- oscillator frequency > > and your baudrate will be as specified. > > Greets, > Kiste > > Am Dienstag, 17. Mai 2022, 21:12:10 MESZ hat flyway38 <[email protected]> > Folgendes geschrieben: > > > Hi again Kiste, > > Here my code pragmas; > > -- Pragmas/ configuration memory settings (fuses) > pragma target clock 20_000_000 -- oscillator frequency > pragma target OSC OFF -- HS crystal or resonator > pragma target RSTOSC HFINT32 -- power-up clock select: > OSC > pragma target CLKOUTEN DISABLED -- no clock output > pragma target WDT DISABLED -- watchdog > pragma target DEBUG DISABLED -- no debugging > pragma target BROWNOUT DISABLED -- no brownout reset > pragma target FCMEN DISABLED -- no clock monitoring > pragma target CSWEN ENABLED -- allow writing OSCCON1 > NOSC and NDIV > pragma target LVP DISABLED -- no low voltage > programming > pragma target MCLR EXTERNAL -- external reset > -- The configuration bit settings above are only a selection, sufficient > -- for this program. Other programs may need more or different settings. > -- > WDTCON_SWDTEN = OFF -- disable watchdog > -- > _usec_delay (100_000) -- wait for power to > stablilize > -- > enable_digital_io() -- make all pins digital > I/O > > Cheers > Filipe Santos. > On Tuesday, May 17, 2022 at 7:05:54 PM UTC+1 Kiste wrote: > > Hi Filipe, > > > I suspect the baudrate problem in settings like > > pragma target clock ? > pragma target OSC ? > pragma target RSTOSC ? > > OSCCON* = ? > > What are these settings? > > Greets, > Kiste > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/6e0906ee-c9ec-4f45-94fb-3f99356d83aen%40googlegroups.com > > <https://groups.google.com/d/msgid/jallib/6e0906ee-c9ec-4f45-94fb-3f99356d83aen%40googlegroups.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "jallib" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/jallib/2a51961c-ca87-4ba0-b033-c7898ef83840n%40googlegroups.com.
