Great Rob !!! It works perfect. See the difference with what i had before.:
Files\Microchip\MPLABX\v5.45\mplab_platform\mplab_ipe\pk3cmd.exe" -TPPK3 -Pport -MPIC -Fcom5 -OL with now *Echo off* *REM PICkit3 batch file for programming from JALEdit.* *Echo Programming Device %1 from file %2 ...* *"C:\Program Files\Microchip\MPLABX\v5.45\mplab_platform\mplab_ipe\pk3cmd.exe" -P%1 -F%2 -MPIC* *Thanks* *Hans* Op zaterdag 30 juli 2022 om 19:39:21 UTC+2 schreef [email protected]: > Hi Hans, > > I cannot send a batch file since it is blocked by Outlook. Create a > batchfile e.g. called pic_program.bat with the following content: > > > *Echo off * > *REM PICkit3 batch file for programming from JALEdit.* > *Echo Programming Device %1 from file %2 ...* > *"C:\Program > Files\Microchip\MPLABX\v6.00\mplab_platform\mplab_ipe\pk3cmd.exe" -P%1 -F%2 > -MPIC* > > > On JALEdit you have to set the following for the programmer: > > > If you program it from JALEdit you will see this: > > > > Good Luck! > > Kind regards, > > Rob > > ------------------------------ > *Van:* [email protected] <[email protected]> namens hans < > [email protected]> > *Verzonden:* zaterdag 30 juli 2022 15:54 > > *Aan:* jallib <[email protected]> > *Onderwerp:* Re: [jallib] Wisp648 > Hello, > I still haven't managed to control the Pickit3 with that batch file. > I have now gone back to the old way, loading the old ones with the Wisp648 > and the newer one the hex with Pickit3. > If I've done something wrong, I'd like to hear about it. > Thank you > regards > Hans > > Op vrijdag 29 juli 2022 om 19:14:49 UTC+2 schreef [email protected]: > > Yes, we have completed that integration work. We support all the > programmers that we have always supported. We can share how we did this. > > Get Outlook for Android <https://aka.ms/AAb9ysg> > ------------------------------ > *From:* [email protected] <[email protected]> on behalf of > Rob CJ <[email protected]> > *Sent:* Friday, July 29, 2022 7:07:07 PM > > *To:* [email protected] <[email protected]> > *Subject:* Re: [jallib] Wisp648 > Hi Evan, > > Thanks for the info. I do not know GCSTUDIO so not sure how to apply it to > the question I had. > > I was just wondering if there where people that have tried some kind of > integration using Visual Studio Code with a programmer. > > I know that Sunish made a field for it but I never tried it. Maybe I > should do that first. > > Kind regards, > > Rob > > ------------------------------ > *Van:* 'Evan Venn' via jallib <[email protected]> > *Verzonden:* donderdag 28 juli 2022 20:02 > *Aan:* [email protected] <[email protected]> > *Onderwerp:* Re: [jallib] Wisp648 > > Rob, > > We can share our work with VSCode to create GCSTUDIO. We have written the > scripting interface and should you decide to leverage our work then this > may save months of work. Our development of GCSTUDIO started in January > and we are just completing (scripts, helpers, snippets, autocomplete etc > etc) > > Your call, of course. > > Get Outlook for Android <https://aka.ms/AAb9ysg> > ------------------------------ > *From:* [email protected] <[email protected]> on behalf of > Rob CJ <[email protected]> > *Sent:* Thursday, July 28, 2022 7:20:15 PM > *To:* [email protected] <[email protected]> > *Subject:* Re: [jallib] Wisp648 > > Hi all, > > I have two related questions to this subject. Sunish has made this > beautiful JAL extension for Visual Studio Code which I nowadays use for all > my JAL developments. There have been some recent updates of Visual Studio > Code that eases programming by for example detecting and indicating missing > closing brackets. > > Did anybody of you ever tried to use Visual Studio Code in combination > with a programmer using a commandl ine or script for the PICKit3? > > Normally I create my program in Visual Studio Code and compile it from > within Visual Studio code using ctrl-shift-b and I use the PICkit3 > standalone software in the 'auto reload/program' mode so that when a new > hexfile is generated it automatically reprograms my PIC. This works very > fast. > > I do believe that if I would use a command line interface and start the > programmer from Visual Studio Code that it will be slower since it needs to > restart the programmer software each time I want to use it. Or is there > another way to do that? > > Thanks > > Kind regards, > > Rob > > ------------------------------ > *Van:* [email protected] <[email protected]> namens hans < > [email protected]> > *Verzonden:* donderdag 28 juli 2022 15:56 > *Aan:* jallib <[email protected]> > *Onderwerp:* Re: [jallib] Wisp648 > > Have tested if it works from mplab as i have done until now : (start > mplab, load hex file and program,) works perfect > > Op donderdag 28 juli 2022 om 15:50:34 UTC+2 schreef hans: > > Tested from jaledit , it opened the batch and teh same eror message : > C:\Users\Gebruiker\Desktop>"C:\Program > Files\Microchip\MPLABX\v5.45\mplab_platform\mplab_ipe\pk3cmd.exe" -TPPK3 > -Pport -MPIC -Fcom5 -OL > > Illegal command line parameter T > Press any key to continue . . . > > Op donderdag 28 juli 2022 om 13:12:20 UTC+2 schreef vasile: > > "Gefeliciteerd" > seems ok for me. :) > > BTW, if you use pickit4, you will need anyway to install the IPE to change > the supply voltage, then to plug and unplug and plug again the pickit until > IPE sees it...then fortunately to program something. Never leave it in the > USB when you start the computer if you do not want to send it to Microchip > irish office for reflashing the Atmel inside or exchanging with a new > one... Pickit4 needs to behave with it as you'll do with eggs. On the > opposite of Pickit2/3 which can be reflashed at home... > best wishes > > > On Thu, Jul 28, 2022 at 8:56 AM hans <[email protected]> wrote: > > Hi Sunish, > I have made my first batch: > > @ECHO OFF > Echo Gefeliciteerd > PAUSE > > "C:\Program > Files\Microchip\MPLABX\v5.45\mplab_platform\mplab_ipe\pk3cmd.exe" -TPPK3 > -P%1 -MPIC -F%2 -OL > @if ERRORLEVEL 1 pause > > It works but gives an error message ; > > Gefeliciteerd > Press any key to continue . . . > Illegal command line parameter T > Press any key to continue . . . > Op woensdag 27 juli 2022 om 17:16:30 UTC+2 schreef hans: > > Hi Sunish, > This sounds great ! I have never made a batch file and use the Pickit not > for providing 5 Volt\ > The IPE is in the regular program file, not in (86), i have foud the same > files you mentioned. > . Please give me an example how to make the batch file. > Thanks > Hans > > Op woensdag 27 juli 2022 om 14:24:59 UTC+2 schreef [email protected]: > > Jaledit can program using Pickit 2 and 3. You will need to install IPE. > > Create a batch file and paste the code - Change the path to reflect your > computer's IPE installation > > *"C:\Program Files > (x86)\Microchip\MPLABX\v5.20\mplab_platform\mplab_ipe\pk3cmd.exe" -TPPK3 > -P%1 -MPIC -F%2 -OL * > *@if ERRORLEVEL 1 pause* > > > In jaledit you will have to set the path to the batch file and pass %D > %F for the PIC name and file name respectively. > the /V5 is to force Pickit to provide 5V supply > > [image: image.png] > > > > Regards, > Sunish > > -- > > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/f295ac0d-880c-48b4-a78d-18fc674db5cdn%40googlegroups.com > > <https://groups.google.com/d/msgid/jallib/f295ac0d-880c-48b4-a78d-18fc674db5cdn%40googlegroups.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/0a9783db-3aca-4c6c-8d85-128ffc9589c6n%40googlegroups.com > > <https://groups.google.com/d/msgid/jallib/0a9783db-3aca-4c6c-8d85-128ffc9589c6n%40googlegroups.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/GVXP195MB1637A41DDE1CD616338AA9DEE6969%40GVXP195MB1637.EURP195.PROD.OUTLOOK.COM > > <https://groups.google.com/d/msgid/jallib/GVXP195MB1637A41DDE1CD616338AA9DEE6969%40GVXP195MB1637.EURP195.PROD.OUTLOOK.COM?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/CWXP265MB25186A8708F26595B33ABDAAF9969%40CWXP265MB2518.GBRP265.PROD.OUTLOOK.COM > > <https://groups.google.com/d/msgid/jallib/CWXP265MB25186A8708F26595B33ABDAAF9969%40CWXP265MB2518.GBRP265.PROD.OUTLOOK.COM?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/GVXP195MB163705DDB23E9EB880FB46E5E6999%40GVXP195MB1637.EURP195.PROD.OUTLOOK.COM > > <https://groups.google.com/d/msgid/jallib/GVXP195MB163705DDB23E9EB880FB46E5E6999%40GVXP195MB1637.EURP195.PROD.OUTLOOK.COM?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/8ee52c76-30cd-438a-8437-91c426ffc474n%40googlegroups.com > > <https://groups.google.com/d/msgid/jallib/8ee52c76-30cd-438a-8437-91c426ffc474n%40googlegroups.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "jallib" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/jallib/22cccf54-499a-4b46-9a06-174b9f094b81n%40googlegroups.com.
