Its Wrong you don't need to OSM modules on SUP720 u can use xconnect vlan100 , the problem is was on Juniper side it cannot receive vlan interface for attachment circuit :))
On Fri, 2007-04-06 at 02:17 +0000, [EMAIL PROTECTED] wrote: > Christian, > > If you want to use EoMPLS xconnect on a SVI (to allow for local switching as > well) then you need a OSM+/SIP400/SIP600/ES20 as the core facing interface. > Without one of these modules, you can only configure the xconnext on a > sub-interface or main interface. > > Hope this helps, > > ----- Message d'origine ----- > De: Christian Malo <[EMAIL PROTECTED]> > Date: Jeudi, Avril 5, 2007 2:57 pm > Objet: [j-nsp] juniper - cisco l2circuit problem > À: [email protected] > > > I setup a basic l2circuit between a sup720 and an m20. > > > > Here's the IOS config and output > > > > interface GigabitEthernet1/2 > > description blahblah > > switchport > > switchport trunk encapsulation dot1q > > switchport trunk allowed vlan 1,100,127 > > switchport mode trunk > > > > interface Vlan100 > > no ip address > > xconnect X.X.Y.110 803 encapsulation mpls > > > > Local interface: Vl100 up, line protocol up, Eth VLAN 100 up > > Destination address: X.X.Y.110, VC ID: 803, VC status: down > > Output interface: none, imposed label stack {794085} > > Preferred path: not configured > > Default path: active > > Next hop: Invalid ADDR > > Create time: 00:12:29, last status change time: 00:03:35 > > Signaling protocol: LDP, peer X.X.Y.110:0 up > > MPLS VC labels: local 38, remote 794085 > > Group ID: local 0, remote 0 > > MTU: local 1500, remote 1500 > > Remote interface description: > > Sequencing: receive disabled, send disabled > > VC statistics: > > packet totals: receive 0, send 0 > > byte totals: receive 0, send 0 > > packet drops: receive 0, send 0 > > > > > > JunOS config and output > > > > unit 518 { > > description "blahblah"; > > encapsulation vlan-ccc; > > vlan-id 518; > > } > > > > neighbor X.X.Y.125 { > > interface ge-0/3/0.518 { > > virtual-circuit-id 803; > > description "blahblah"; > > no-control-word; > > } > > } > > > > Interface Type St Time last up > > # Up trans > > ge-0/3/0.518(vc 803) rmt Up Apr 5 14:39:41 2007 > > 1 > > Local interface: ge-0/3/0.518, Status: Up, Encapsulation: VLAN > > Remote PE: X.X.Y.125, Negotiated control-word: No > > Incoming label: 794085, Outgoing label: 38 > > Time Event > > Interface/Lbl/PE Apr 5 14:39:41 2007 status update timer > > Apr 5 14:39:39 2007 PE route changed > > Apr 5 14:39:39 2007 Out lbl Update > > 38 > > Apr 5 14:39:39 2007 In lbl Update > > 794085 Apr 5 14:39:39 2007 loc intf up > > ge-0/3/0.518 > > > > > > > > LDP session comes up ... it works with ethernet-vlan > > configurations but > > the second I try on vlan interfaces, I get that > > > > > > > > thanks for the help. > > > > > > -chris > > _______________________________________________ > > juniper-nsp mailing list [email protected] > > https://puck.nether.net/mailman/listinfo/juniper-nsp > > > _______________________________________________ > juniper-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/juniper-nsp _______________________________________________ juniper-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/juniper-nsp
