thanks Nilesh and Cristian ,
I checked the autoneg and it seems ok ( show interface extensive) :
Autonegotiation information:
Negotiation status: Complete
Link partner:
Link mode: Full-duplex, Flow control: None, Remote fault: OK
I lunch 2 pings :
ping 10.0.24.1 count 1000
ping logical-router PE2 10.0.123.2 count 1000
and I have been collecting info from FEB but nothing happen always same
result before and during and after the pings :
ad...@m10> start shell pfe network feb
SBR platform (266Mhz PPC 603e processor, 64MB memory, 512KB flash)
SBR(M10 vty)# bringup bchip 0 read 0x3002
B0 0x00003002: 0x00000000
SBR(M10 vty)#
any idea Nilesh?
Cristian :
information in log chassid seems correct and also there no reject on the
"show route ..." command :
log chassid
Dec 21 18:21:01 FPC 0 PIC 3, attaching clean
Dec 21 18:21:01 create_pic_entry: pic i2c 0x214, hw qs 4 supported qs 4,
flags 0x0, pic port 0
Dec 21 18:21:01 create_pic_entry: pic i2c 0x214, hw qs 4 supported qs 4,
flags 0x0, pic port 1
Dec 21 18:21:01 create_pic_entry: pic i2c 0x214, hw qs 4 supported qs 4,
flags 0x0, pic port 2
Dec 21 18:21:01 create_pic_entry: pic i2c 0x214, hw qs 4 supported qs 4,
flags 0x0, pic port 3
Dec 21 18:21:01 CHASSISD_IFDEV_CREATE_NOTICE: create_pics: created
interface device for fe-0/3/0
Dec 21 18:21:01 fe-0/3/0: large delay buffer cleared
Dec 21 18:21:01 CHASSISD_IFDEV_CREATE_NOTICE: create_pics: created
interface device for fe-0/3/1
Dec 21 18:21:01 fe-0/3/1: large delay buffer cleared
Dec 21 18:21:01 CHASSISD_IFDEV_CREATE_NOTICE: create_pics: created
interface device for fe-0/3/2
Dec 21 18:21:01 fe-0/3/2: large delay buffer cleared
Dec 21 18:21:01 CHASSISD_IFDEV_CREATE_NOTICE: create_pics: created
interface device for fe-0/3/3
Dec 21 18:21:01 fe-0/3/3: large delay buffer cleared
Dec 21 18:21:01 hwdb: entry for pic 532 at slot 3 in fpc 0 inserted
Dec 21 18:21:01 PIC message op 1
Dec 21 18:21:06 send: slot_info request for slot 0
Dec 21 18:21:06 send: slot_info request for slot 1
Dec 21 18:21:06 rcv reply: Slot Info 0 State 3
Dec 21 18:21:06 CHASSISD_SNMP_TRAP10: SNMP trap generated: FRU power on
(jnxFruContentsIndex 7, jnxFruL1Index 1, jnxFruL2Index 0, jnxFruL3Index 0,
jnxFruName FPC: @ 0/*/*, jnxFruType 3, jnxFruSlot 1, jnxFruOfflineReason 2,
jnxFruLastPowerOff 0, jnxFruLastPowerOn 10585)
Dec 21 18:21:06 hwdb: entry for pic at slot 0 in fpc 0 updated
Dec 21 18:21:06 rcv: Set Slot Info fpc 0, pic 0 valid
Dec 21 18:21:06 hwdb: entry for pic at slot 1 in fpc 0 updated
Dec 21 18:21:06 rcv: Set Slot Info fpc 0, pic 1 valid
Dec 21 18:21:06 hwdb: entry for pic at slot 2 in fpc 0 updated
Dec 21 18:21:06 rcv: Set Slot Info fpc 0, pic 2 valid
Dec 21 18:21:06 hwdb: entry for pic at slot 3 in fpc 0 updated
Dec 21 18:21:06 rcv: Set Slot Info fpc 0, pic 3 valid
Dec 21 18:21:06 rcv reply: Slot Info 1 State 3
Dec 21 18:21:06 CHASSISD_SNMP_TRAP10: SNMP trap generated: FRU power on
(jnxFruContentsIndex 7, jnxFruL1Index 2, jnxFruL2Index 0, jnxFruL3Index 0,
jnxFruName FPC: @ 1/*/*, jnxFruType 3, jnxFruSlot 2, jnxFruOfflineReason 2,
jnxFruLastPowerOff 0, jnxFruLastPowerOn 10585)
Dec 21 19:44:23
show route logical-router PE2
inet.0: 2 destinations, 2 routes (2 active, 0 holddown, 0 hidden)
+ = Active Route, - = Last Active, * = Both
10.0.123.0/30 *[Direct/0] 12:12:45
> via fe-0/3/0.123
10.0.123.1/32 *[Local/0] 12:12:48
Local via fe-0/3/0.123
show route logical-router PE3
inet.0: 2 destinations, 2 routes (2 active, 0 holddown, 0 hidden)
+ = Active Route, - = Last Active, * = Both
10.0.123.0/30 *[Direct/0] 10:47:51
> via fe-0/3/1.123
10.0.123.2/32 *[Local/0] 12:20:04
Local via fe-0/3/1.123
here is the configuration again :
fe-0/3/0 and fe-0/3/1 back to back connection ( crossover cable )
fe-0/3/2 =>> connected to annother router
set logical-routers PE2 interfaces fe-0/3/0 unit 123 vlan-id 123
set logical-routers PE2 interfaces fe-0/3/0 unit 123 family inet address
10.0.123.1/30
set logical-routers PE3 interfaces fe-0/3/1 unit 123 vlan-id 123
set logical-routers PE3 interfaces fe-0/3/1 unit 123 family inet address
10.0.123.2/30
set chassis aggregated-devices ethernet device-count 1
set interfaces fe-0/3/0 vlan-tagging
set interfaces fe-0/3/1 vlan-tagging
set interfaces fe-0/3/2 unit 0 family inet address 10.0.24.2/30
set interfaces fxp0 unit 0 family inet address 172.31.16.35/25
set interfaces fxp1 disable
any idea
thanks guys
On Tue, Dec 21, 2010 at 11:01 PM, Nilesh Khambal<[email protected]>wrote:
One thing to check would be auto negotiation on the ports. 4xFE port does
not work in half-duplex mode. If the AN fails we would fall back to
half-duplex mode and the pic would basically not forward anything out of
the
port. From the FEB colllect this command output by running a ping across
the
port in background. Take multiple snapshots.
To log into the FEB, do "start shell pfe network feb0|cfeb0" depending on
whether its M10 or M10i.
- bringup bchip 0 read 0x3002
Thanks,
Nilesh.
On 12/21/10 1:46 PM, "Cristian Frizziero"<[email protected]
wrote:
Ok,
It looks like a hardware problem (at PIC or EFEB level, may be).
I´d be a good idea to change the cable too.... just in case....
Check with show log chassid , may be you can find some log related to a
physical problem.
Also check with a show route logical-router PE2 or PE3. You must find
your subnets and physical addresses of your interfaces. If you find
some
route marked as rejected you could think in some problem of
connectivity
in L1.
Good luck
logo impre
Ing. Cristian Frizziero
Honorio Pueyrredon 1475 -- Buenos Aires
Tel+54.11.4855.6041 (Ext.517)
Cel+54.9.11.6249.1303
[email protected]<mailto:[email protected]>
www.iquall.net<http://www.iquall.net>
El 21/12/2010 18:34, juniper light escribió:
I didn't change cabling, but I connected a new interface to annother
router and I'm having the same problem, the new interface is in the
default configuration :
set interfaces fe-0/3/2 unit 0 family inet address 10.0.24.2/30
<http://10.0.24.2/30>
ad...@m10<mailto:ad...@m10>> show interfaces terse
Interface Admin Link Proto Local
Remote
...
fe-0/3/0 up up
fe-0/3/0.123 up up inet 10.0.123.1/30
<http://10.0.123.1/30>
fe-0/3/0.32767 up up
fe-0/3/1 up up
fe-0/3/1.123 up up inet 10.0.123.2/30
<http://10.0.123.2/30>
fe-0/3/1.32767 up up
fe-0/3/2 up up
fe-0/3/2.0 up up inet 10.0.24.2/30<
http://10.0.24.2/30>
fe-0/3/3 up up
any idea guys ?
BR // Mounir
On Tue, Dec 21, 2010 at 7:25 PM, Cristian Frizziero
[email protected]<mailto:[email protected]>
wrote:
Hi!!
I'd try to change ports pairs, and to switch the PIC to a
different fpc slot, just to be sure that there is no hardware
issue....
The configuration looks fine....
Cristian
El 21/12/2010 15:07, juniper light escribió:
Hi guys, I would like to use M10 to simulate 3 PE, using
logical-routers ( Junos 8.4R4.2 ) I connected 2 fastethernet
back-to-back, link are UP. but when I tried configuring vlan-id ,
I cannot ping from one Logical router to the other : first
scenario using Vlan-tagging : set logical-routers PE2 interfaces
fe-0/3/0 unit 23 vlan-id 123 set logical-routers PE2 interfaces
fe-0/3/0 unit 23 family inet address 10.0.123.1/30
<http://10.0.123.1/30> set logical-routers PE3 interfaces
fe-0/3/1 unit 23 vlan-id 123 set logical-routers PE3 interfaces
fe-0/3/1 unit 23 family inet address 10.0.123.2/30
<http://10.0.123.2/30> set interfaces fe-0/3/0 vlan-tagging set
interfaces fe-0/3/1 vlan-tagging ad...@m10> show interfaces
terse
Interface Admin Link Proto Local Remote ... fe-0/3/0 up up
fe-0/3/0.123 up up inet 10.0.123.1/30 fe-0/3/0.32767
<http://10.0.123.1/30fe-0/3/0.32767> up up fe-0/3/1 up up
fe-0/3/1.123 up up inet 10.0.123.2/30 fe-0/3/1.32767
<http://10.0.123.2/30fe-0/3/1.32767> up up fe-0/3/2 up up
fe-0/3/3 up up Second scenario without Vlan-tagging : set
logical-routers PE2 interfaces fe-0/3/0 unit 0 family inet
address 10.0.123.1/30<http://10.0.123.1/30> set logical-routers
PE3 interfaces fe-0/3/1 unit 0 family inet address 10.0.123.2/30
<http://10.0.123.2/30> ad...@m10> ping logical-router PE2
10.0.123.2 source 10.0.123.1 PING 10.0.123.2 (10.0.123.2): 56
data bytes nothing happen ...... ad...@m10> show interfaces
terse
Interface Admin Link Proto Local Remote ... fe-0/3/0 up up
fe-0/3/0.0 up up inet 10.0.123.1/30 fe-0/3/1
<http://10.0.123.1/30fe-0/3/1> up up fe-0/3/1.0 up up inet
10.0.123.2/30 fe-0/3/2<http://10.0.123.2/30fe-0/3/2> up up
fe-0/3/3 up up ad...@m10
show chassis hardware
Hardware inventory:
Item Version Part number Serial number
Description
Chassis xxxx M10
Midplane REV 03 710-001950 xxx M10
Backplane
Power Supply A Rev 05 740-002497 xxx AC Power
Supply
Display REV 04 710-001995 xxx M10 Display
Board
Routing Engine REV 07 740-007603 xxx RE-3.0
FEB REV 08 710-003310 xx E-FEB
FPC 0 E-FPC
PIC 1 REV 05 750-003163 xxx 1x G/E,
1000
BASE-SX
PIC 3 REV 06 750-002992 xxx 4x F/E, 100
BASE-TX
FPC 1 E-FPC
Fan Tray Rear
Left Fan
Tray
Any idea about that ?
Thanks for your help,
Kind Regards
// Mounir
_______________________________________________
juniper-nsp mailing [email protected]
<mailto:[email protected]>
https://puck.nether.net/mailman/listinfo/juniper-nsp
_______________________________________________
juniper-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/juniper-nsp
