Hi all,
Twenty days later, the error reappeared. The error appears in the log
always after a "RPD_SCHED_SLIP: 5 sec scheduler slip, user: 0 sec 0
usec, system: 4 sec, 228450 usec" messages:
/
Oct 13 23:16:35.278 2011 LEV[2625]: RPD_SCHED_SLIP: 5 sec
scheduler slip, user: 0 sec 0 usec, system: 4 sec, 228450 usec
Oct 13 23:17:35.862 2011 LEV[2625]: RPD_SCHED_SLIP: 4 sec
scheduler slip, user: 0 sec 0 usec, system: 3 sec, 804772 usec
Oct 13 23:20:07.655 2011 LEV[2625]: RPD_SCHED_SLIP: 4 sec
scheduler slip, user: 0 sec 0 usec, system: 3 sec, 750490 usec
Oct 13 23:27:43.598 2011 LEV[2625]: RPD_SCHED_SLIP: 4 sec
scheduler slip, user: 0 sec 0 usec, system: 3 sec, 78894 usec
Oct 13 23:28:14.755 2011 LEV[2625]: RPD_SCHED_SLIP: 5 sec
scheduler slip, user: 0 sec 0 usec, system: 3 sec, 903324 usec
Oct 13 23:29:16.124 2011 LEV[2625]: RPD_SCHED_SLIP: 5 sec
scheduler slip, user: 0 sec 0 usec, system: 4 sec, 166013 usec
Oct 13 23:31:18.118 2011 LEV[2625]: RPD_SCHED_SLIP: 5 sec
scheduler slip, user: 0 sec 0 usec, system: 3 sec, 598753 usec
Oct 13 23:35:46.293 2011 ssb NH: resolutions from iif 82 throttled
Oct 13 23:38:25.256 2011 LEV[2625]: RPD_SCHED_SLIP: 4 sec
scheduler slip, user: 0 sec 0 usec, system: 3 sec, 762067 usec
Oct 13 23:38:55.759 2011 LEV[2625]: RPD_SCHED_SLIP: 5 sec
scheduler slip, user: 0 sec 0 usec, system: 4 sec, 171438 usec
Oct 13 23:41:01.342 2011 ssb NH: resolutions from iif 88 throttled
Oct 13 23:42:16.283 2011 ssb NH: resolutions from iif 93 throttled
Oct 13 23:46:05.391 2011 smartd[2595]: Device: /dev/ad1a,
Failed attribute: (200)Write Error Rate
/
Could this be related?.
Best Regards
Isidoro
El 22/09/2011 8:05, Josh Farrelly escribió:
Could you put them both in a Linux box and just 'dd if' them?
-----Original Message-----
From: [email protected]
[mailto:[email protected]] On Behalf Of Jonas Frey (Probe
Networks)
Sent: Thursday, 22 September 2011 12:52
To: Isidoro Cristobal
Cc: [email protected]
Subject: Re: [j-nsp] HDD Write Error
Dear Isidoro,
you cant copy the data 1:1....atleast not without alot of work.
The best thing would be if you reinstall JunOS via a install media (pcmcia/cf
card) once you replaced the hard disk.
Its very easy to replace the hard disk on either RE2/3/4/5...its normally only
secured by 4 screens on the RE.
Make sure to save your config files (JunOS config, SSH keys, other data like
home directorys, logs etc) before you replace the HDD if neccessary.
Best regards,
Jonas
Am Mittwoch, den 21.09.2011, 17:18 +0200 schrieb Isidoro Cristobal:
Hi,
First of all thank you very much for your quick response .
How to save the data to the new hard disk? Do you know a procedure for
replacing hard disk ?
Best Regards,
Isidoro
El 20/09/2011 17:29, Jonas Frey (Probe Networks) escribió:
Hi,
you are correct, the disk exceeded the maximum write errors
permitted by the SMART value and thus is marked as bad. Prepare for
a complete failure of the drive soon (1-30 days likely).
May be the right time to upgrade the harddisk to a SSD.
http://juniper.cluepon.net/Replacing_the_harddisk_with_solid_state_f
lash
Best regards,
Jonas
Am Dienstag, den 20.09.2011, 17:09 +0200 schrieb Juniper GOWEX:
Hi all,
From yesterday at the log of my M20 are the following message :
smartd[2595]: Device: /dev/ad1a, Failed attribute: (200)Write
Error Rate
It´s informative, but i think that there is a problem with my HDD (
I still have to run the smartd commands ) .
Somebody had this problem ?
Best Regards
Isidoro
_______________________________________________
juniper-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/juniper-nsp
_______________________________________________
juniper-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/juniper-nsp
_______________________________________________
juniper-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/juniper-nsp
