Hello, havent you changed the HDD yet? Like to live dangerously eh? :-)
This is very likely related because those errors messages causes writes to the HDD....and if your HDD is dead/has bad sectors that will cause trouble. Good luck, Jonas Am Mittwoch, den 19.10.2011, 16:19 +0200 schrieb Juniper GOWEX: > Hi all, > > Twenty days later, the error reappeared. The error appears in the log > always after a "RPD_SCHED_SLIP: 5 sec scheduler slip, user: 0 sec 0 > usec, system: 4 sec, 228450 usec" messages: > > > / > Oct 13 23:16:35.278 2011 LEV[2625]: RPD_SCHED_SLIP: 5 sec > scheduler slip, user: 0 sec 0 usec, system: 4 sec, 228450 usec > Oct 13 23:17:35.862 2011 LEV[2625]: RPD_SCHED_SLIP: 4 sec > scheduler slip, user: 0 sec 0 usec, system: 3 sec, 804772 usec > Oct 13 23:20:07.655 2011 LEV[2625]: RPD_SCHED_SLIP: 4 sec > scheduler slip, user: 0 sec 0 usec, system: 3 sec, 750490 usec > Oct 13 23:27:43.598 2011 LEV[2625]: RPD_SCHED_SLIP: 4 sec > scheduler slip, user: 0 sec 0 usec, system: 3 sec, 78894 usec > Oct 13 23:28:14.755 2011 LEV[2625]: RPD_SCHED_SLIP: 5 sec > scheduler slip, user: 0 sec 0 usec, system: 3 sec, 903324 usec > Oct 13 23:29:16.124 2011 LEV[2625]: RPD_SCHED_SLIP: 5 sec > scheduler slip, user: 0 sec 0 usec, system: 4 sec, 166013 usec > Oct 13 23:31:18.118 2011 LEV[2625]: RPD_SCHED_SLIP: 5 sec > scheduler slip, user: 0 sec 0 usec, system: 3 sec, 598753 usec > Oct 13 23:35:46.293 2011 ssb NH: resolutions from iif 82 throttled > Oct 13 23:38:25.256 2011 LEV[2625]: RPD_SCHED_SLIP: 4 sec > scheduler slip, user: 0 sec 0 usec, system: 3 sec, 762067 usec > Oct 13 23:38:55.759 2011 LEV[2625]: RPD_SCHED_SLIP: 5 sec > scheduler slip, user: 0 sec 0 usec, system: 4 sec, 171438 usec > Oct 13 23:41:01.342 2011 ssb NH: resolutions from iif 88 throttled > Oct 13 23:42:16.283 2011 ssb NH: resolutions from iif 93 throttled > Oct 13 23:46:05.391 2011 smartd[2595]: Device: /dev/ad1a, > Failed attribute: (200)Write Error Rate > / > > Could this be related?. > > Best Regards > > Isidoro > > > > El 22/09/2011 8:05, Josh Farrelly escribió: > > Could you put them both in a Linux box and just 'dd if' them? > > > > -----Original Message----- > > From: [email protected] > > [mailto:[email protected]] On Behalf Of Jonas Frey (Probe > > Networks) > > Sent: Thursday, 22 September 2011 12:52 > > To: Isidoro Cristobal > > Cc: [email protected] > > Subject: Re: [j-nsp] HDD Write Error > > > > Dear Isidoro, > > > > you cant copy the data 1:1....atleast not without alot of work. > > The best thing would be if you reinstall JunOS via a install media > > (pcmcia/cf card) once you replaced the hard disk. > > Its very easy to replace the hard disk on either RE2/3/4/5...its normally > > only secured by 4 screens on the RE. > > Make sure to save your config files (JunOS config, SSH keys, other data > > like home directorys, logs etc) before you replace the HDD if neccessary. > > > > Best regards, > > Jonas > > > > Am Mittwoch, den 21.09.2011, 17:18 +0200 schrieb Isidoro Cristobal: > >> Hi, > >> > >> First of all thank you very much for your quick response . > >> > >> How to save the data to the new hard disk? Do you know a procedure for > >> replacing hard disk ? > >> > >> Best Regards, > >> > >> Isidoro > >> > >> > >> > >> El 20/09/2011 17:29, Jonas Frey (Probe Networks) escribió: > >>> Hi, > >>> > >>> you are correct, the disk exceeded the maximum write errors > >>> permitted by the SMART value and thus is marked as bad. Prepare for > >>> a complete failure of the drive soon (1-30 days likely). > >>> May be the right time to upgrade the harddisk to a SSD. > >>> http://juniper.cluepon.net/Replacing_the_harddisk_with_solid_state_f > >>> lash > >>> > >>> Best regards, > >>> Jonas > >>> > >>> > >>> > >>> Am Dienstag, den 20.09.2011, 17:09 +0200 schrieb Juniper GOWEX: > >>>> Hi all, > >>>> > >>>> From yesterday at the log of my M20 are the following message : > >>>> > >>>> smartd[2595]: Device: /dev/ad1a, Failed attribute: (200)Write > >>>> Error Rate > >>>> > >>>> It´s informative, but i think that there is a problem with my HDD ( > >>>> I still have to run the smartd commands ) . > >>>> > >>>> Somebody had this problem ? > >>>> > >>>> > >>>> Best Regards > >>>> > >>>> Isidoro > >>>> > >>>> > >>>> _______________________________________________ > >>>> juniper-nsp mailing list [email protected] > >>>> https://puck.nether.net/mailman/listinfo/juniper-nsp > > _______________________________________________ > > juniper-nsp mailing list [email protected] > > https://puck.nether.net/mailman/listinfo/juniper-nsp > _______________________________________________ > juniper-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/juniper-nsp
signature.asc
Description: This is a digitally signed message part
_______________________________________________ juniper-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/juniper-nsp
