it says DRAM test fails, my guess is you need to replace memory. On Wed, Nov 28, 2012 at 8:57 PM, Ali Sumsam <[email protected]> wrote: > Here are some more errors if it helps > > > tunefs: soft updates remains unchanged as disabled > > Creating initial configuration...Interface control process: > /usr/libexec/ld-elf.so.1: Shared object "libcrypto.so.3" not found, > required by "cgatool" > > umass0: at uhub0 port 3 (addr 2) disconnected > > (da0:umass-sim0:0:0:0): lost device > > g_vfs_done():da0s1a[WRITE(offset=8192, length=2048)]error = 6 > > umass0: detached > > umass1: at uhub0 port 2 (addr 3) disconnected > > (da1:umass-sim1:1:0:0): lost device > > g_vfs_done():da1s1f[WRITE(offset=8192, length=2048)]error = 6 > > mgd: warning: panic: vinvalbuf: dirty bufs > > Uptime: 1m29s > > (da0:dead_sim0:0:0:0): Synchronize cache failed, status == 0x8, scsi status > == 0x0 > > (da1:dead_sim0:0:0:0): Synchronize cache failed, status == 0x8, scsi status > == 0x0 > > Cannot dump. No dump device defined. > > Automatic reboot in 15 seconds - press a key on the console to abort > > > *Ali Sumsam CCIE* > *Network Engineer - Level 3* > eintellego Pty Ltd > [email protected] ; www.eintellego.net > > Phone: 1300 753 383 ; Fax: (+612) 8572 9954 > > Cell +61 (0)410 603 531 > > facebook.com/eintellego > PO Box 7726, Baulkham Hills, NSW 1755 Australia > > The Experts Who The Experts Call > Juniper - Cisco – Brocade - IBM > > > > On Thu, Nov 29, 2012 at 12:21 PM, Ali Sumsam > <[email protected]>wrote: > >> Hi, >> >> My new MX5 died today. If I try to boot it up, it stuck at following >> message. >> >> U-Boot 1.1.6 (Jun 10 2011 - 00:50:30) >> >> CPU: 8572, Version: 2.1, (0x80e00021) >> Core0: E500, Version: 3.0, (0x80210030) >> Clock Configuration: >> CPU0:1333 MHz, CPU1:1333 MHz, CCB: 533 MHz, >> DDR: 267 MHz (533 MT/s data rate) (Synchronous), LBC: 33 MHz >> L1: D-cache 32 kB enabled >> I-cache 32 kB enabled >> Board: MX5-T 1.8 >> CPLD: Version 0x1f >> DRAM: Initializing - DDR: 2048 MB >> Testing DRAM from 0x00000000 to 0x80000000 >> DRAM test phase 1: >> DRAM test fails at: 7ff63e24 >> hang at function = 0xfffbe504 >> ### ERROR ### Please RESET the board ### >> >> >> Any suggestions? >> >> Regards, >> >> *Ali Sumsam CCIE* >> *Network Engineer - Level 3* >> eintellego Pty Ltd >> [email protected] ; www.eintellego.net >> >> Phone: 1300 753 383 ; Fax: (+612) 8572 9954 >> >> Cell +61 (0)410 603 531 >> >> facebook.com/eintellego >> PO Box 7726, Baulkham Hills, NSW 1755 Australia >> >> The Experts Who The Experts Call >> Juniper - Cisco – Brocade - IBM >> >> > _______________________________________________ > juniper-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/juniper-nsp
_______________________________________________ juniper-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/juniper-nsp
