I'd try to use install-media to get everything back to factory defaults. Have you tried this yet?
With best regards, Vitaly Vlasenko On 29.11.2012, at 12:04, 叶雨飞 <[email protected]> wrote: > it says DRAM test fails, my guess is you need to replace memory. > > On Wed, Nov 28, 2012 at 8:57 PM, Ali Sumsam > <[email protected]> wrote: >> Here are some more errors if it helps >> >> >> tunefs: soft updates remains unchanged as disabled >> >> Creating initial configuration...Interface control process: >> /usr/libexec/ld-elf.so.1: Shared object "libcrypto.so.3" not found, >> required by "cgatool" >> >> umass0: at uhub0 port 3 (addr 2) disconnected >> >> (da0:umass-sim0:0:0:0): lost device >> >> g_vfs_done():da0s1a[WRITE(offset=8192, length=2048)]error = 6 >> >> umass0: detached >> >> umass1: at uhub0 port 2 (addr 3) disconnected >> >> (da1:umass-sim1:1:0:0): lost device >> >> g_vfs_done():da1s1f[WRITE(offset=8192, length=2048)]error = 6 >> >> mgd: warning: panic: vinvalbuf: dirty bufs >> >> Uptime: 1m29s >> >> (da0:dead_sim0:0:0:0): Synchronize cache failed, status == 0x8, scsi status >> == 0x0 >> >> (da1:dead_sim0:0:0:0): Synchronize cache failed, status == 0x8, scsi status >> == 0x0 >> >> Cannot dump. No dump device defined. >> >> Automatic reboot in 15 seconds - press a key on the console to abort >> >> >> *Ali Sumsam CCIE* >> *Network Engineer - Level 3* >> eintellego Pty Ltd >> [email protected] ; www.eintellego.net >> >> Phone: 1300 753 383 ; Fax: (+612) 8572 9954 >> >> Cell +61 (0)410 603 531 >> >> facebook.com/eintellego >> PO Box 7726, Baulkham Hills, NSW 1755 Australia >> >> The Experts Who The Experts Call >> Juniper - Cisco – Brocade - IBM >> >> >> >> On Thu, Nov 29, 2012 at 12:21 PM, Ali Sumsam >> <[email protected]>wrote: >> >>> Hi, >>> >>> My new MX5 died today. If I try to boot it up, it stuck at following >>> message. >>> >>> U-Boot 1.1.6 (Jun 10 2011 - 00:50:30) >>> >>> CPU: 8572, Version: 2.1, (0x80e00021) >>> Core0: E500, Version: 3.0, (0x80210030) >>> Clock Configuration: >>> CPU0:1333 MHz, CPU1:1333 MHz, CCB: 533 MHz, >>> DDR: 267 MHz (533 MT/s data rate) (Synchronous), LBC: 33 MHz >>> L1: D-cache 32 kB enabled >>> I-cache 32 kB enabled >>> Board: MX5-T 1.8 >>> CPLD: Version 0x1f >>> DRAM: Initializing - DDR: 2048 MB >>> Testing DRAM from 0x00000000 to 0x80000000 >>> DRAM test phase 1: >>> DRAM test fails at: 7ff63e24 >>> hang at function = 0xfffbe504 >>> ### ERROR ### Please RESET the board ### >>> >>> >>> Any suggestions? >>> >>> Regards, >>> >>> *Ali Sumsam CCIE* >>> *Network Engineer - Level 3* >>> eintellego Pty Ltd >>> [email protected] ; www.eintellego.net >>> >>> Phone: 1300 753 383 ; Fax: (+612) 8572 9954 >>> >>> Cell +61 (0)410 603 531 >>> >>> facebook.com/eintellego >>> PO Box 7726, Baulkham Hills, NSW 1755 Australia >>> >>> The Experts Who The Experts Call >>> Juniper - Cisco – Brocade - IBM >> _______________________________________________ >> juniper-nsp mailing list [email protected] >> https://puck.nether.net/mailman/listinfo/juniper-nsp > > _______________________________________________ > juniper-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/juniper-nsp _______________________________________________ juniper-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/juniper-nsp
