Yes it does.
Olive + L2VPN is a special case since only Intel PRO 100 (fxp0) and
Interl PRO 1000 (em0) NICs are supported by Olive, and AFAIK, these
cards firmware doesn't support L2VPN data plane operations.
Olive + L3VPN does work fine, both control and data plane.
Thx
Alex
On 18/04/2016 19:59, Aaron wrote:
Thanks Alex, does it work on vMX ?
Aaron
-----Original Message-----
From: juniper-nsp [mailto:[email protected]] On Behalf Of
Alexander Arseniev
Sent: Monday, April 18, 2016 11:26 AM
To: [email protected]
Subject: Re: [j-nsp] MPLS L2VPN Cisco and Juniper
Hello,
If You are doing the below JUNOS config on Olive, L2circuit data plane does
not work on Olive.
And it never worked on Olive, to my knowledge.
HTH
Thx
Alex
On 18/04/2016 13:32, Mohammad Khalil wrote:
I have configured the below
set interfaces em0 mtu 1514
set interfaces em0 unit 0 family inet address 192.168.101.10/24 set
interfaces em0 unit 0 family mpls mtu 1500 set interfaces em1
vlan-tagging set interfaces em1 unit 100 encapsulation vlan-ccc set
interfaces em1 unit 100 vlan-id 100 set interfaces em1 unit 100 family
ccc set interfaces lo0 unit 0 family inet address 10.10.10.10/32 set
routing-options router-id 10.10.10.10 set routing-options
autonomous-system 20 set protocols mpls interface em0.0 set protocols
mpls interface lo0.0 set protocols ospf area 0.0.0.0 interface em0.0
set protocols ospf area 0.0.0.0 interface lo0.0 set protocols ldp
interface em0.0 set protocols ldp interface lo0.0 set protocols
l2circuit neighbor 1.1.1.1 interface em1.100 virtual-circuit-id 100
router ospf 1
router-id 1.1.1.1
network 1.1.1.1 0.0.0.0 area 0
network 192.168.101.1 0.0.0.0 area 0 R1#sh run int f1/1.100 Building
configuration...
Current configuration : 107 bytes
!
interface FastEthernet1/1.100
encapsulation dot1Q 100
xconnect 10.10.10.10 100 encapsulation mpls end
But its not working even the circuit is up (not working means no ping
between CEs)
BR,
Mohammad
On Mon, Apr 18, 2016 at 2:47 PM, Mohammad Khalil <[email protected]>
wrote:
Thanks Steinar
So we are talking about xconnect from Cisco side and l2circuit from
Juniper side right?
Do you have a running template please?
Thanks in advance
BR,
Mohammad
On Mon, Apr 18, 2016 at 1:49 PM, <[email protected]> wrote:
Am trying to configure MPLS L2VPN between Cisco and Juniper I know
in Cisco VPLS and xconnect In juniper l2vpn and l2circuit (Kompella
and Martini respectively) What are the compatible methods to follow
in this case?
Point to point (pseudowire, Martini tunnel) is very much
interoperable between Cisco and Juniper. We have lots of these in
operation.
Steinar Haug, Nethelp consulting, [email protected]
_______________________________________________
juniper-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/juniper-nsp
_______________________________________________
juniper-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/juniper-nsp
_______________________________________________
juniper-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/juniper-nsp
