Hi, The SP(ALOM/iLOM) can see all of the hardware, regardless of the LDM config. So if you are only seeing CMP0/P0 -> CMP0/P55, then you only have 6 cores in your UltraSPARC-T2 proc. If there was a problem, it would still list the cores. *-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-* Octave J. Orgeron Solaris Systems Engineer http://www.opensolaris.org/os/community/sysadmin/ http://unixconsole.blogspot.com unixconsole at yahoo.com *-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*
----- Original Message ---- From: Armando Galibardi <[email protected]> To: ldoms-discuss at opensolaris.org Sent: Friday, March 28, 2008 11:31:35 AM Subject: Re: [ldoms-discuss] Reset LDOM Configuration Thanks for your advice, I tried your suggestions in point 2); I got always the same result Below the output of commands: sc> showcomponent /SYS/MB/CMP0/P0 ?. ?. ?. /SYS/MB/CMP0/P55 sc> showhost Sun System Firmware 7.0.9.c 2008/01/14 22:51 Host flash versions: Hypervisor 1.5.6 2007/11/30 08:29 OBP 4.27.10 2007/12/07 10:45 POST 4.27.10 2007/12/07 11:10 sc> showplatform SUNW,SPARC-Enterprise-T5220 Chassis Serial Number: BEL08067HA Domain Status ------ ------ S0 Running sc> showkeyswitch Keyswitch is in the NORMAL position. BR Armando -----Original Message----- From: Rudolf Kutina [mailto:[email protected]] Sent: venerd? 28 marzo 2008 16.09 To: Armando Galibardi Cc: ldoms-discuss at opensolaris.org Subject: Re: [ldoms-discuss] Reset LDOM Configuration Hi Armanod, 1. First check in you really have 8 cores by sc> showcomponent You must see 64 /SYS/MB/CMP0/Pxx lines 2. Try reset SC (may be even power on/off whole box, this helps one time on T2000) sc> poweroff sc> bootmode config=?factory-default? sc> resetsc -y 3. What Firmware/HW you have ? Send us outputs of: sc> showhost sc> showplatform sc> showkeyswitch Nice day Rudolf Kutina Armando Galibardi wrote: > Hi all, > > I've tried again the following steps: > > [b]sc> poweroff > sc> bootmode config=?factory-default? > sc> poweron[/b] > > after that I got always the same strange situation: > if i issue ldm list I got 48 VCPU > if I issue prtdiag I got 56 VCPU (it seems to be a non-sense result) > > Thanks all for your response > > Armando > -- > This message was posted from opensolaris.org > _______________________________________________ > ldoms-discuss mailing list > ldoms-discuss at opensolaris.org > http://mail.opensolaris.org/mailman/listinfo/ldoms-discuss > -- This message was posted from opensolaris.org _______________________________________________ ldoms-discuss mailing list ldoms-discuss at opensolaris.org http://mail.opensolaris.org/mailman/listinfo/ldoms-discuss ____________________________________________________________________________________ Be a better friend, newshound, and know-it-all with Yahoo! Mobile. Try it now. http://mobile.yahoo.com/;_ylt=Ahu06i62sR8HDtDypao8Wcj9tAcJ
