I am using the latest Xcode. I need to figure out what is happening here. Maybe this is a macports issue. I could dump it and top to home-brew...
On Sat, Nov 2, 2013 at 2:32 PM, Lifepillar <[email protected]> wrote: > I've built Ledger's master branch with Homebrew and the executable is 3.7 > MB. > Adding --with-python --with-debug results in an executable of 8.3 MB. > > In either case, I haven't noticed any perceivable slow down, but my files > amount > to less than 200 KB. Ledger reg takes approximately 0.6 s, and ledger bal > about > 40ms. > > Do you have the latest Xcode? > > Life > > In article > <caks9tol8qlsrkendv_3xcwv0dectc7sahpng0_qorgforqh...@mail.gmail.com>, > Craig Earls <[email protected]> wrote: > > > Interestingly enough I just cloned a clean source tree and built four > > flavors of executable +/- python +/i debug and all have the same > executable > > size...28125284 > > > > acprep reported the desired build flavor before starting off...hmmmm... > > > > > > On Thu, Oct 31, 2013 at 3:05 PM, Craig Earls > > <[email protected]> wrote: > > > > > I just verified with Time Machine that the old executable was 4.3MB. > No > > > sure what is going on here. > > > > > > > > > On Thu, Oct 31, 2013 at 2:50 PM, Craig Earls > > > <[email protected]> wrote: > > > > > >> Running my typical balance operations seems much slower, but I don't > have > > >> the old executable times to compare against... > > >> > > >> The new executable time for a single account balance is : > > >> > > >> 14:48:09 ~/FinanceData (master) > time ledger bal VWCU > > >> > > >> $ X,XXXX.XX Assets:VWCU > > >> > > >> $ X,XXX.XX Grace > > >> > > >> $ X,XXX.XX Joint > > >> > > >> $ XXX.XX Michaela > > >> > > >> $ X,XXX.XX Savings > > >> > > >> -------------------- > > >> > > >> $ XX,XXX.XX > > >> > > >> > > >> real 0m1.146s > > >> > > >> user 0m1.058s > > >> > > >> sys 0m0.048s > > >> > > >> I am prêt sure this was far less than 0.5 seconds before. Running > > >> balance commands from with ledger-mode was practically instantaneous > > >> before > > >> but now has noticeable lag. > > >> > > >> > > >> On Thu, Oct 31, 2013 at 1:19 PM, John Wiegley > > >> <[email protected]>wrote: > > >> > > >>> >>>>> Craig Earls <[email protected]> > > >>> >>>>> writes: > > >>> > > >>> > I did a clean build from fresh source and got the binary size > down. It > > >>> > still seems much slower than before... > > >>> > > >>> Slower at which operations? Do you have timing results? > > >>> > > >>> John > > >>> > > >>> -- > > >>> > > >>> --- > > >>> You received this message because you are subscribed to the Google > > >>> Groups "Ledger" group. > > >>> To unsubscribe from this group and stop receiving emails from it, > send > > >>> an email to > > >>> [email protected]. > > >>> For more options, visit https://groups.google.com/groups/opt_out. > > >>> > > >> > > >> > > >> > > >> -- > > >> Craig, Corona De Tucson, AZ > > >> enderw88.wordpress.com > > >> > > > > > > > > > > > > -- > > > Craig, Corona De Tucson, AZ > > > enderw88.wordpress.com > > > > > > > > > > > -- > > Craig, Corona De Tucson, AZ > > enderw88.wordpress.com > > -- > > --- > You received this message because you are subscribed to the Google Groups > "Ledger" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > For more options, visit https://groups.google.com/groups/opt_out. > -- Craig, Corona De Tucson, AZ enderw88.wordpress.com -- --- You received this message because you are subscribed to the Google Groups "Ledger" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/groups/opt_out.
