I just rebuilt it using brew. Problem solved. Binary is 8MB and snappy as it should be.
On Sat, Nov 2, 2013 at 7:30 PM, Craig Earls <[email protected]> wrote: > I am using the latest Xcode. I need to figure out what is happening here. > Maybe this is a macports issue. I could dump it and top to home-brew... > > > On Sat, Nov 2, 2013 at 2:32 PM, Lifepillar <[email protected]> wrote: > >> I've built Ledger's master branch with Homebrew and the executable is 3.7 >> MB. >> Adding --with-python --with-debug results in an executable of 8.3 MB. >> >> In either case, I haven't noticed any perceivable slow down, but my files >> amount >> to less than 200 KB. Ledger reg takes approximately 0.6 s, and ledger bal >> about >> 40ms. >> >> Do you have the latest Xcode? >> >> Life >> >> In article >> <caks9tol8qlsrkendv_3xcwv0dectc7sahpng0_qorgforqh...@mail.gmail.com>, >> Craig Earls <[email protected]> wrote: >> >> > Interestingly enough I just cloned a clean source tree and built four >> > flavors of executable +/- python +/i debug and all have the same >> executable >> > size...28125284 >> > >> > acprep reported the desired build flavor before starting off...hmmmm... >> > >> > >> > On Thu, Oct 31, 2013 at 3:05 PM, Craig Earls >> > <[email protected]> wrote: >> > >> > > I just verified with Time Machine that the old executable was 4.3MB. >> No >> > > sure what is going on here. >> > > >> > > >> > > On Thu, Oct 31, 2013 at 2:50 PM, Craig Earls >> > > <[email protected]> wrote: >> > > >> > >> Running my typical balance operations seems much slower, but I don't >> have >> > >> the old executable times to compare against... >> > >> >> > >> The new executable time for a single account balance is : >> > >> >> > >> 14:48:09 ~/FinanceData (master) > time ledger bal VWCU >> > >> >> > >> $ X,XXXX.XX Assets:VWCU >> > >> >> > >> $ X,XXX.XX Grace >> > >> >> > >> $ X,XXX.XX Joint >> > >> >> > >> $ XXX.XX Michaela >> > >> >> > >> $ X,XXX.XX Savings >> > >> >> > >> -------------------- >> > >> >> > >> $ XX,XXX.XX >> > >> >> > >> >> > >> real 0m1.146s >> > >> >> > >> user 0m1.058s >> > >> >> > >> sys 0m0.048s >> > >> >> > >> I am prêt sure this was far less than 0.5 seconds before. Running >> > >> balance commands from with ledger-mode was practically instantaneous >> > >> before >> > >> but now has noticeable lag. >> > >> >> > >> >> > >> On Thu, Oct 31, 2013 at 1:19 PM, John Wiegley >> > >> <[email protected]>wrote: >> > >> >> > >>> >>>>> Craig Earls <[email protected]> >> > >>> >>>>> writes: >> > >>> >> > >>> > I did a clean build from fresh source and got the binary size >> down. It >> > >>> > still seems much slower than before... >> > >>> >> > >>> Slower at which operations? Do you have timing results? >> > >>> >> > >>> John >> > >>> >> > >>> -- >> > >>> >> > >>> --- >> > >>> You received this message because you are subscribed to the Google >> > >>> Groups "Ledger" group. >> > >>> To unsubscribe from this group and stop receiving emails from it, >> send >> > >>> an email to >> > >>> [email protected]. >> > >>> For more options, visit https://groups.google.com/groups/opt_out. >> > >>> >> > >> >> > >> >> > >> >> > >> -- >> > >> Craig, Corona De Tucson, AZ >> > >> enderw88.wordpress.com >> > >> >> > > >> > > >> > > >> > > -- >> > > Craig, Corona De Tucson, AZ >> > > enderw88.wordpress.com >> > > >> > >> > >> > >> > -- >> > Craig, Corona De Tucson, AZ >> > enderw88.wordpress.com >> >> -- >> >> --- >> You received this message because you are subscribed to the Google Groups >> "Ledger" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> For more options, visit https://groups.google.com/groups/opt_out. >> > > > > -- > Craig, Corona De Tucson, AZ > enderw88.wordpress.com > -- Craig, Corona De Tucson, AZ enderw88.wordpress.com -- --- You received this message because you are subscribed to the Google Groups "Ledger" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/groups/opt_out.
