Tom I am sorry that I did not answer your question about the ER 20 system . They are mainly used in the metal work trade. However They can be used for wood work. I use them with milling cutters, and the drawback with them is that they are parallel shank to cutter. This of course means that a change of cutter size means that one has to also change the collet I have never used a normal router cutter larger than 3/4" and 1/2" shank in the ER20 The milling cutters from the far east are so cheap and I just use them for planing cuts or grooving. I know nothing Re: Diamond saws but am learning something new every time I go back to messages on this site, that are years old. Yesterday using my Revo I used a 1/2" milling cutter to plane a spindle 30 inches long by 1 1/4"Dia Turned both handles at the same speed ----- it looked like the rats had been at it----------- must get a motor drive to the spindle, like I have on the Old Woodchuck, that leaves a perfect finish on spindles using the same 1/2" milling cutter. *Further more I do not need the exercise by the turning of handles !!!!!????* Regards Richard
On Saturday, June 10, 2017 at 4:07:09 PM UTC+1, Tom Dotta wrote: > > Hi Richard & Curtis > > Two things I'd like to hear more about. ER20 system and diamond hole saws > for use on a router?? > > Cheers Tom D > > On Sat, Jun 10, 2017 at 7:43 AM, CURTIS GEORGE <curtg...@wowway.com > <javascript:>> wrote: > >> Hello and Good morning Everyone. >> I have the Xtreme Xtension chuck on my router, I do like it, But having >> said that have been looking at the muscle chuck for a while and DO plan to >> buy one. >> Here is there web site. http://www.musclechuck.com/ I have switched >> form my PC to a Craftsman router for my Legacy, I was told that the Bosh >> (#4) chuck would work for me, so I plan to buy one soon. >> I agree with Richard using the old router col let type of chucks are a >> Pain! >> >> As far as Router bits go. Magnate is a very good company, but I use what >> ever I can get my hands on, metal working end mills (both carbide and >> H,S,S.) are also part of my arsenal of tools that I use with my Legacy. >> (NOTE) Two flute end mills work the best on wood, ones made to cut Alum. >> are what I look for the most. The end mills that have more flutes tend to >> bog up with wood chips, so stay clear of those for the main stay, But end >> mills are cheaper to buy and higher quality for the most part. but the >> section of profiles is limited compared with router bits. >> but for the small/detail jobs, I use what ever I can find, HSS (cheep) >> bits can do well for small jobs, so keep your eyes open, you just may find >> something that works for you even if its not made to work with a router... >> One more example are my diamond hole saws, They work very well for detail >> work, they are much safer to use then an Fly cutter would be on a router. >> but again (I must stress ) they are ONLY for detail work, >> >> Gota run now. >> Have a good weekend everyone. >> C.A.G. >> >> ------------------------------ >> *From: *"Bawdsey64" <rhp...@gmail.com <javascript:>> >> *To: *"Bill Bulkeley" <bulk...@mmnet.com.au <javascript:>>, "Mike Pung" < >> legacy-orna...@googlegroups.com <javascript:>> >> *Sent: *Saturday, June 10, 2017 10:02:13 AM >> *Subject: *RE: Routers >> >> >> A word of warning DO NOT PUT AN XTREME XTENSION IN A MUSCLE CHUCK, that >> can be lethal and they are not meant to be used together. >> >> >> Of the two products I prefer the Xtreme Xtension but that is because Bob >> at Router Technologies built it originally for me after the guy at Muscle >> Chuck or what ever his company was called at that time would only build his >> product for Porter Cable! Bob even sent him his design for the Xtreme >> Xtension but he did not want to know so Bob went ahead and built it. >> >> >> If you are in the UK or Europe then both products are available from >> www.woodworkersworkshop.co.uk and by the way I am not involved with that >> company in any way these days. >> Cheers >> >> Roger >> >> >> Sent from TouchMail for Windows 10 <http://bit.ly/1PH8eIw> >> >> >> >> >> >> *From:* Bill Bulkeley >> *Received:* 10/06/2017 14:52:10 +01:00 >> *To:* legacy-orna...@googlegroups.com <javascript:> >> >> I use nothing but triton routers on my mills, router table and free hand >> I love them. >> >> They are all fitted either with the quick change musclechuck or the >> xtream xtension depending on the reach I need. >> >> Rather than change chucks on one router I change the whole router for >> another, I have several fitted with different quick change chucks. >> >> The triton routers are the only routers here that have fast removal and >> replace mounting from machine to machine, one of the reasons i like them so >> much. >> >> loosen 2 wing nut like screws slide a little and it’s off done. I can >> change routers in about 10 seconds. >> >> When I have it on the legacy I have one or both of the routers plastic >> shields removed so I can get easily to the router bit and also the legacy T >> ball hex key fits all the quick change chucks so changing bits is easy and >> all the cutting takes place lower down so the shields don’t do much anyway >> in this case. >> >> When I started I bought this set first >> https://www.magnate.net/ProductDetails.asp?ProductCode=RBPROFESSIONAL >> >> Then kept adding and adding bits mostly from magnate others from ebay or >> were ever i saw bits i think i could use now i have that many it’s >> ridiculous I was a bit a holic for a while J >> >> >> >> Bill >> >> >> >> >> >> >> >> *From:* legacy-orna...@googlegroups.com <javascript:> [mailto: >> legacy-ornamental-mills@googlegroups.com <javascript:>] *On Behalf Of >> *Richard >> Ellis >> *Sent:* Saturday, 10 June 2017 4:40 PM >> *To:* Legacy Ornamental Mills >> *Subject:* Routers >> >> >> >> Wondering what sort of routers do most of you use. And did you buy sets >> of cutters or buy them individually ??? >> >> I have a Triton TRA 001 on my Woodchuck and a Dewalt 625 E on my Revo. >> >> Bill I always find it a pain to change cutters on the Triton-------- need >> three hands, although it is easy to do in a vertical position in the router >> table. >> >> On the Legacy's I usually have something under the cutter to save it from >> falling on the floor. Sometimes I wedge the lock button in with a length of >> wood. >> >> Be nice if the button stayed put. The routers both have the ER 20 collet >> system They allow me to use milling cutters. >> >> Regards to all ,and lets have more posts, surely someone has a question >> or two >> >> Richard >> >> -- >> You received this message because you are subscribed to the Google Groups >> "Legacy Ornamental Mills" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to legacy-ornamental-mills+unsubscr...@googlegroups.com >> <javascript:>. >> To post to this group, send email to legacy-orna...@googlegroups.com >> <javascript:>. >> Visit this group at >> https://groups.google.com/group/legacy-ornamental-mills. >> For more options, visit https://groups.google.com/d/optout. >> >> >> >> >> <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> >> >> Virus-free. www.avg.com >> <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> >> >> >> >> >> -- >> You received this message because you are subscribed to the Google Groups >> "Legacy Ornamental Mills" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to legacy-ornamental-mills+unsubscr...@googlegroups.com >> <javascript:>. >> To post to this group, send email to legacy-orna...@googlegroups.com >> <javascript:>. >> Visit this group at >> https://groups.google.com/group/legacy-ornamental-mills. >> For more options, visit https://groups.google.com/d/optout. >> >> >> -- >> You received this message because you are subscribed to the Google Groups >> "Legacy Ornamental Mills" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to legacy-ornamental-mills+unsubscr...@googlegroups.com >> <javascript:>. >> To post to this group, send email to legacy-orna...@googlegroups.com >> <javascript:>. >> Visit this group at >> https://groups.google.com/group/legacy-ornamental-mills. >> For more options, visit https://groups.google.com/d/optout. >> >> -- >> You received this message because you are subscribed to the Google Groups >> "Legacy Ornamental Mills" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to legacy-ornamental-mills+unsubscr...@googlegroups.com >> <javascript:>. >> To post to this group, send email to legacy-orna...@googlegroups.com >> <javascript:>. >> Visit this group at >> https://groups.google.com/group/legacy-ornamental-mills. >> For more options, visit https://groups.google.com/d/optout. >> > > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
