Here is a better description of my problem.
I am building a new RHEL AS 3 system from Linux version 2.4.21-4.EL (Red Hat
Linux 3.2.3-20)
I put all the networking configuration information in, and I can connect to
the new initial ram disk system.
I supply the DASD device numbers of "151,200,201,202,203"
I then LOGN to ROOT on the initial system and see some of the following on
the system console
dasd(eckd): ECKD discipline initializing
dasd: <devno: 0151> Add lowmem page :15247000
dasd: <devno: 0151> Add lowmem page :15245000
dasd(eckd): /dev/dasda ( 94: 0),[EMAIL PROTECTED]: 3390/0A(CU:3990/01) Cyl:250
Head:15 S
ec:224
dasd(eckd): /dev/dasda ( 94: 0),[EMAIL PROTECTED]: 3390/0A(CU:3990/01):
Configuration da
ta read
dasd: No request IRQ
dasd: <devno: 0200> Add lowmem page :1523d000
dasd: <devno: 0200> Add lowmem page :1523c000
dasd(eckd): /dev/dasdb ( 94: 4),[EMAIL PROTECTED]: 3390/0A(CU:3990/01) Cyl:100
Head:15 S
ec:224
dasd(eckd): /dev/dasdb ( 94: 4),[EMAIL PROTECTED]: 3390/0A(CU:3990/01):
Configuration da
ta read
dasd: No request IRQ
dasd: waiting for responses...
dasd(eckd): /dev/dasda ( 94: 0),[EMAIL PROTECTED]: (4kB blks): 180000kB at 48kB/trk
linu
x disk layout
dasd: No request IRQ
dasd: <devno: 0201> Add lowmem page :15234000
dasd: <devno: 0201> Add lowmem page :15233000
dasd(eckd): /dev/dasdc ( 94: 8),[EMAIL PROTECTED]: 3390/0A(CU:3990/01) Cyl:3338
Head:15
Sec:224
dasd(eckd): /dev/dasdc ( 94: 8),[EMAIL PROTECTED]: 3390/0A(CU:3990/01):
Configuration da
ta read
dasd: No request IRQ
dasd: waiting for responses...
dasd(eckd): /dev/dasdb ( 94: 4),[EMAIL PROTECTED]: (4kB blks): 72000kB at 48kB/trk
linux
And then toward the end I see this information:
Partition check:
dasda:CMS1/ SWAP : dasda1
dasdb:CMS1/ BOOT : dasdb1
dasdc:CMS1/ ROOT : dasdc1
dasdd:CMS1/ VAR : dasdd1
dasde:CMS1/ HOME : dasde1
dasd(eckd): We are interested in: CU 3880/00
dasd(eckd): We are interested in: CU 3990/00
dasd(eckd): We are interested in: CU 2105/00
dasd(eckd): We are interested in: CU 9343/00
* inserted /tmp/dasd_eckd_mod.o
* load module set done
* no firewire controller found
* no pcic controller found
* probing buses
* finished bus probing
* found nothing
At this point I start the install process. Select the NFS Setup option. Then
after id mounts the NFS Disk I get this prompt:
+------------+ Warning +------------+
| |
| No hard drives have been found. |
| You probably need to manually |
| choose device drivers for the |
| installation to succeed. Would |
| you like to select drivers now? |
| |
| +-----+ +----+ |
| | Yes | | No | |
| +-----+ +----+ |
| |
| |
+-----------------------------------+
I select yes, Then I get this prompt
+------------------+ Devices +------------------+
| |
| No device drivers have been loaded for your |
| system. Would you like to load any now? |
| |
| |
| +------+ +------------+ |
| | Done | | Add Device | |
| +------+ +------------+ |
| |
| |
+-----------------------------------------------+
But the only driver I see is for S/390 Channel to Channel (ctc)
TIA, \|/
(. .)
____ooO-(_)-Ooo____
Larry Davis, 6-2380
