I try that now and let you know. Larry
-----Original Message----- From: Post, Mark K [mailto:[EMAIL PROTECTED] Sent: Tuesday, March 02, 2004 16:43 PM To: [EMAIL PROTECTED] Subject: Re: NO DASD on RHEL AS 3 Pull off a new copy of the kernel and initrd and use those instead of the ones from the original disks. They may not have changed, but it's quick and easy. Mark Post -----Original Message----- From: Linux on 390 Port [mailto:[EMAIL PROTECTED] On Behalf Of Davis, Larry Sent: Tuesday, March 02, 2004 3:38 PM To: [EMAIL PROTECTED] Subject: Re: NO DASD on RHEL AS 3 Can I proceed to perform the install using the update1 disk1-4 ISO images? I down loaded that at the same time I downloaded the BASE Disk1-4 ISO images. Larry -----Original Message----- From: Eric Sammons [mailto:[EMAIL PROTECTED] Sent: Tuesday, March 02, 2004 15:30 PM To: [EMAIL PROTECTED] Subject: Re: NO DASD on RHEL AS 3 It is believed that this problem is resolved with UPDATE 1 of RHEL 3. I am preparing to test this myself as I have the same problem and a report has been opened with bugzilla. Red Hat has forwarded me the following Link to obtain a copy of update 1. You may want to talk to your RH rep. Thanks! Eric Sammons "Davis, Larry" <[EMAIL PROTECTED]> Sent by: Linux on 390 Port <[EMAIL PROTECTED]> 03/01/2004 11:12 AM Please respond to Linux on 390 Port To: [EMAIL PROTECTED] cc: Subject: NO DASD on RHEL AS 3 Here is a better description of my problem. I am building a new RHEL AS 3 system from Linux version 2.4.21-4.EL (Red Hat Linux 3.2.3-20) I put all the networking configuration information in, and I can connect to the new initial ram disk system. I supply the DASD device numbers of "151,200,201,202,203" I then LOGN to ROOT on the initial system and see some of the following on the system console dasd(eckd): ECKD discipline initializing dasd: <devno: 0151> Add lowmem page :15247000 dasd: <devno: 0151> Add lowmem page :15245000 dasd(eckd): /dev/dasda ( 94: 0),[EMAIL PROTECTED]: 3390/0A(CU:3990/01) Cyl:250 Head:15 S ec:224 dasd(eckd): /dev/dasda ( 94: 0),[EMAIL PROTECTED]: 3390/0A(CU:3990/01): Configuration da ta read dasd: No request IRQ dasd: <devno: 0200> Add lowmem page :1523d000 dasd: <devno: 0200> Add lowmem page :1523c000 dasd(eckd): /dev/dasdb ( 94: 4),[EMAIL PROTECTED]: 3390/0A(CU:3990/01) Cyl:100 Head:15 S ec:224 dasd(eckd): /dev/dasdb ( 94: 4),[EMAIL PROTECTED]: 3390/0A(CU:3990/01): Configuration da ta read dasd: No request IRQ dasd: waiting for responses... dasd(eckd): /dev/dasda ( 94: 0),[EMAIL PROTECTED]: (4kB blks): 180000kB at 48kB/trk linu x disk layout dasd: No request IRQ dasd: <devno: 0201> Add lowmem page :15234000 dasd: <devno: 0201> Add lowmem page :15233000 dasd(eckd): /dev/dasdc ( 94: 8),[EMAIL PROTECTED]: 3390/0A(CU:3990/01) Cyl:3338 Head:15 Sec:224 dasd(eckd): /dev/dasdc ( 94: 8),[EMAIL PROTECTED]: 3390/0A(CU:3990/01): Configuration da ta read dasd: No request IRQ dasd: waiting for responses... dasd(eckd): /dev/dasdb ( 94: 4),[EMAIL PROTECTED]: (4kB blks): 72000kB at 48kB/trk linux And then toward the end I see this information: Partition check: dasda:CMS1/ SWAP : dasda1 dasdb:CMS1/ BOOT : dasdb1 dasdc:CMS1/ ROOT : dasdc1 dasdd:CMS1/ VAR : dasdd1 dasde:CMS1/ HOME : dasde1 dasd(eckd): We are interested in: CU 3880/00 dasd(eckd): We are interested in: CU 3990/00 dasd(eckd): We are interested in: CU 2105/00 dasd(eckd): We are interested in: CU 9343/00 * inserted /tmp/dasd_eckd_mod.o * load module set done * no firewire controller found * no pcic controller found * probing buses * finished bus probing * found nothing At this point I start the install process. Select the NFS Setup option. Then after id mounts the NFS Disk I get this prompt: +------------+ Warning +------------+ | | | No hard drives have been found. | | You probably need to manually | | choose device drivers for the | | installation to succeed. Would | | you like to select drivers now? | | | | +-----+ +----+ | | | Yes | | No | | | +-----+ +----+ | | | | | +-----------------------------------+ I select yes, Then I get this prompt +------------------+ Devices +------------------+ | | | No device drivers have been loaded for your | | system. Would you like to load any now? | | | | | | +------+ +------------+ | | | Done | | Add Device | | | +------+ +------------+ | | | | | +-----------------------------------------------+ But the only driver I see is for S/390 Channel to Channel (ctc) TIA, \|/ (. .) ____ooO-(_)-Ooo____ Larry Davis, 6-2380
