Still getting same error. Changed to
0xa210 0x01:0x5005076300d08276 0x00:0x502f000000000000
0xa310 0x01:0x5005076300c28276 0x00:0x502f000000000000
And reran "mk_initrd" and "zipl" and "fdisk /dev/sda". The messages were
the same
sd: allocated major 8
sd: find_free_slot ...<7>sd: ... found 08:00
Attached scsi disk sda at scsi0, channel 0, id 1, lun 0
sd: find_free_slot ...<7>sd: ... found 08:10
Attached scsi disk sdb at scsi1, channel 0, id 1, lun 0
zfcp: FSF: zfcp_fsf_send_fcp_command_task_handler: status for
SCSI Command:
00000000 0000
zfcp: FSF: zfcp_fsf_send_fcp_command_task_handler: SCSI status
code 0x2
00000000 00000000 00000202 00000000 00000020 00000000
70000600 00000018 00000000 29000000 00000400 00000000 00000000
00000000
SCSI device sda: 7812544 512-byte hdwr sectors (4000 MB)
sda: sda1
zfcp: FSF: zfcp_fsf_send_fcp_command_task_handler: status for
SCSI Command:
00000000 0000
zfcp: FSF: zfcp_fsf_send_fcp_command_task_handler: SCSI status
code 0x2
00000000 00000000 00000202 00000000 00000020 00000000
70000600 00000018 00000000 29000000 00000400 00000000 00000000
00000000
SCSI device sdb: 7812544 512-byte hdwr sectors (4000 MB)
sdb: sdb1
zfcp: config: zfcp_unit_enqueue: Warning: A Unit with SCSI LUN
0x0 already exists. Skipping record.
zfcp: SCSI: zfcp_config_parse_record_add: warning: unable to add
record: 0xa210 1:0x5005076300d08276 0:0x502f000000000000
zfcp: SCSI: zfcp_add_map_proc_write: Warning: One or several
mapping entries were not added to the module configuration.
-----Original Message-----
From: Linux on 390 Port [mailto:[EMAIL PROTECTED] On Behalf Of
Seader, Cameron
Sent: Thursday, December 23, 2004 11:07 AM
To: [email protected]
Subject: Re: FCP question
YOu went wrong on the zfcp.conf configuration. you will notice that
where you put in the 0x1: you need to have a 0x01 and where you put in
the LUN # of 0x0: you need to have 0x00:, it is very picky. If you have
one thing wrong it won't work.
-Cameron
-----Original Message-----
From: Linux on 390 Port [mailto:[EMAIL PROTECTED] Behalf Of
Wiggins, Mark
Sent: Thursday, December 23, 2004 09:04
To: [email protected]
Subject: Re: FCP question
Last question I hope. I've since created an /etc/zfcp.conf file with the
following.
0xa210 0x1:0x5005076300d08276 0x0:0x502f000000000000
0xa310 0x1:0x5005076300c28276 0x0:0x502f000000000000
I ran "mk_initrd" and zipl. Upon reboot a I noticed the following in the
logs,
sd: allocated major 8
sd: find_free_slot ...<7>sd: ... found 08:00
Attached scsi disk sda at scsi0, channel 0, id 1, lun 0
sd: find_free_slot ...<7>sd: ... found 08:10
Attached scsi disk sdb at scsi1, channel 0, id 1, lun 0
zfcp: FSF: zfcp_fsf_send_fcp_command_task_handler: status for
SCSI Command:
00000000 0000
zfcp: FSF: zfcp_fsf_send_fcp_command_task_handler: SCSI status
code 0x2
00000000 00000000 00000202 00000000 00000020 00000000
70000600 00000018 00000000 29000000 00000400 00000000 00000000
00000000
SCSI device sda: 7812544 512-byte hdwr sectors (4000 MB)
sda: sda1
zfcp: FSF: zfcp_fsf_send_fcp_command_task_handler: status for
SCSI Command:
00000000 0000
zfcp: FSF: zfcp_fsf_send_fcp_command_task_handler: SCSI status
code 0x2
00000000 00000000 00000202 00000000 00000020 00000000
70000600 00000018 00000000 29000000 00000400 00000000 00000000
00000000
SCSI device sdb: 7812544 512-byte hdwr sectors (4000 MB)
sdb: sdb1
zfcp: config: zfcp_unit_enqueue: Warning: A Unit with SCSI LUN
0x0 already exists. Skipping record.
zfcp: SCSI: zfcp_config_parse_record_add: warning: unable to add
record: 0xa210 1:0x5005076300d08276 0:0x502f000000000000
zfcp: SCSI: zfcp_add_map_proc_write: Warning: One or several
mapping entries were not added to the module configuration.
It seems as though I am not "multipathing". Where did I go wrong???
SLES8/zVM 5.1.
Mark Wiggins
-
----------------------------------------------------------------------
For LINUX-390 subscribe / signoff / archive access instructions,
send email to [EMAIL PROTECTED] with the message: INFO LINUX-390 or visit
http://www.marist.edu/htbin/wlvindex?LINUX-390
