Look like the driver is loading and registering the frontend but no joy using ztap.
Robert #dmesg i2c-core.o: i2c core module version 2.8.1 (20031005) Linux video capture interface: v1.00 bttv: driver version 0.9.12 loaded bttv: snapshot date 2004-01-21 bttv: using 4 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). bttv0: Bt878 (rev 17) at 02:0b.0, irq: 23, latency: 64, mmio: 0xfbefc000 bttv0: detected: Nebula Electronics DigiTV [card=104], PCI subsystem ID is 0071:0101 bttv0: using: Nebula Electronics DigiTV [card=104,insmod option] bttv0: gpio: en=00000000, out=00000000 in=00ff48cb [init] bttv0: using tuner=-1 bttv0: registered device video0 bttv0: registered device vbi0 bttv0: PLL: 28636363 => 35468950 .. ok bttv: Bt8xx card found (1). bttv1: Bt878 (rev 17) at 02:0a.0, irq: 22, latency: 64, mmio: 0xfbefe000 bttv1: subsystem: 1461:0761 (UNKNOWN) please mail id, board name and the correct card= insmod option to [EMAIL PROTECTED] bttv1: using: *** UNKNOWN/GENERIC *** [card=0,autodetected] bttv1: gpio: en=00000000, out=00000000 in=009c004d [init] bttv1: using tuner=-1 bttv1: i2c: checking for MSP34xx @ 0x80... not found bttv1: i2c: checking for TDA9875 @ 0xb0... not found bttv1: i2c: checking for TDA7432 @ 0x8a... not found bttv1: registered device video1 bttv1: registered device vbi1 bt878: AUDIO driver version 0.0.0 loaded bt878: Bt878 AUDIO function found (0). bt878(0): Bt878 (rev 17) at 02:0b.1, irq: 23, latency: 64, memory: 0xfbefd000 bt878: Bt878 AUDIO function found (1). bt878(1): Bt878 (rev 17) at 02:0a.1, irq: 22, latency: 64, memory: 0xfbeff000 DVB: registering new adapter (Neb). DVB: registering new adapter (Ave). DVB: registering frontend 0:0 (NxtWave NXT6000)... #linuxtv-dvb-apps-1.1.0/util/szap/tzap -c channels.conf "sbs digital 1" using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' tuning to 536500000 Hz video pid 0x00a1, audio pid 0x0051 status 01 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 | status 01 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 | status 01 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 | status 01 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 | status 01 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 | status 01 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 | status 03 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 | status 01 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 | status 03 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 | status 03 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 | status 01 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 | status 01 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 | -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Holger Waechtler Sent: Monday, 26 January 2004 9:53 PM To: [EMAIL PROTECTED] Subject: [linux-dvb] Re: Nebula DigiTV and nxt6000 problems Robert Cook wrote: > The board revision is E 03/2003 > > It has the following chips: > > About 1cm square > NxtWave communications > Nxt 6000 > DD8376 > 1A1 0304 Ok, then they still have the Ntx6000 onboard. Hmmm - I read again your first mail and there you mentioned that it was already working, so sorry for confusion. But now I remember the problem: Gerd Knorr said that the bt8xx it is not able to send zero-byte messages using the hardware i2c controller thus you get -EINVAL when trying to check which PLL is onboard - so you need the software bitbanging driver for the nxt6000. I modified the nxt6000 driver so that it does not sends zero-length messages anymore, can you please test and report whether it works for you? Holger -- Info: To unsubscribe send a mail to [EMAIL PROTECTED] with "unsubscribe linux-dvb" as subject. -- Info: To unsubscribe send a mail to [EMAIL PROTECTED] with "unsubscribe linux-dvb" as subject.
