For what I understand, changing the Firmware 64 to 60000200 changes the if
frequency to 5.2MHz. So this modification on the firmware should make the
card work. What it's more strange for me is that when trying to scan no
signal or SNR is reported, so it seems like xc3028 firmware is not working
properly. Perhaps could be a wrong BASE or DTV firmware loaded?

Albert

2008/2/16, Albert Comerma <[EMAIL PROTECTED]>:
>
> So, If it's not a problem, any of you could send me the current xc3028
> firmware you are using, because mine does not seem to work... Thanks.
>
> Albert
>
> 2008/2/15, Patrick Boettcher <[EMAIL PROTECTED]>:
> >
> > Aah now I remember that issue, in fact it is no issue. I was seeing that
> > problem when send the sleep command or any other firmware command
> > without
> > having a firmware running. In was, so far, no problem.
> >
> > Patrick.
> >
> >
> >
> > On Fri, 15 Feb 2008, Holger Dehnhardt wrote:
> >
> > > Hi Albert, Hi Mauro,
> > >
> > > I have successfulli patched and compiled the driver. Im using the
> > terratec
> > > cinergy device and it works fine.
> > >
> > >>> [ 2251.856000] xc2028 4-0061: Error on line 1063: -5
> > >
> > > This error message looked very familar to me, so i searched my log and
> > guess
> > > what I found:
> > >
> > > Feb 15 20:42:18 musik kernel: xc2028 3-0061: xc2028_sleep called
> > > Feb 15 20:42:18 musik kernel: xc2028 3-0061: xc2028_sleep called
> > > Feb 15 20:42:18 musik kernel: xc2028 3-0061: Error on line 1064: -5
> > > Feb 15 20:42:18 musik kernel: DiB7000P: setting output mode for demod
> > df75e800
> > > to 0
> > > Feb 15 20:42:18 musik kernel: DiB7000P: setting output mode for demod
> > df75e800
> > > to 0
> > >
> > > It identifies the marked line (just to be sure because of the differen
> > line
> > > numbers)
> > >
> > >       if (priv->firm_version < 0x0202)
> > > ->            rc = send_seq(priv, {0x00, 0x08, 0x00, 0x00});
> > >       else
> > >               rc = send_seq(priv, {0x80, 0x08, 0x00, 0x00});
> > >
> > >> The above error is really weird. It seems to be related to something
> > that
> > >> happened before xc2028, since firmware load didn't start on that
> > point of
> > >> the code.
> > >
> > > The error really is weird, but it does not seem to cause the troubles
> > - my
> > > card works despite the error!
> > >
> > >>
> > >>> [ 2289.284000] xc2028 4-0061: Device is Xceive 3028 version 1.0,
> > firmware
> > >>> version 2.7
> > >>
> > >> This message means that xc3028 firmware were successfully loaded and
> > it is
> > >> running ok.
> > >
> > > This and the following messages look similar...
> > >
> > > Holger
> > >
> > > _______________________________________________
> > > linux-dvb mailing list
> > > linux-dvb@linuxtv.org
> > > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
> > >
> >
> > _______________________________________________
> > linux-dvb mailing list
> > linux-dvb@linuxtv.org
> > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
> >
>
>
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

Reply via email to