On 17/09/2025 22:25, Dang Huynh via B4 Relay wrote:
> From: Dang Huynh <dang.hu...@mainlining.org>
>
> RDA Micro RDA8810PL includes an SD/MMC controller. This controller
> supports SD/SDIO/MMC interface.
>
> Signed-off-by: Dang Huynh <dang.hu...@mainlining.org>
> ---
> MAINTAINERS | 6 +
> drivers/mmc/host/Kconfig | 12 +
> drivers/mmc/host/Makefile | 1 +
> drivers/mmc/host/rda-mmc.c | 853
> +++++++++++++++++++++++++++++++++++++++++++++
> 4 files changed, 872 insertions(+)
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index
> 91be43782f4ba8aacb629002d357a66704f10b2b..33e04ce35dcc4cbadd715ec9199f2453237b8002
> 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -21417,6 +21417,12 @@ S: Maintained
> F: Documentation/devicetree/bindings/rtc/rda,8810pl-rtc.yaml
> F: drivers/rtc/rtc-rda.c
>
> +RDA MICRO SECURE DIGITAL AND MULTIMEDIA CARD DRIVER
> +M: Dang Huynh <dang.hu...@mainlining.org>
> +S: Maintained
> +F: Documentation/devicetree/bindings/mmc/rda,mmc.yaml
> +F: drivers/mmc/host/rda-mmc.c
> +
> RDACM20 Camera Sensor
> M: Jacopo Mondi <jacopo+rene...@jmondi.org>
> M: Kieran Bingham <kieran.bingham+rene...@ideasonboard.com>
> diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
> index
> 4afa0130779d97ca9d1c0ed2102b0babdedcaeeb..352a6eb4e30793b7311c7877c238a7fe31121123
> 100644
> --- a/drivers/mmc/host/Kconfig
> +++ b/drivers/mmc/host/Kconfig
> @@ -1040,6 +1040,18 @@ config MMC_MTK
> This is needed if support for any SD/SDIO/MMC devices is required.
> If unsure, say N.
>
> +config MMC_RDA
> + tristate "RDA Micro SD/MMC Card Interface support"
> + depends on ARCH_RDA
Missing compile test
> + depends on COMMON_CLK
> + depends on HAS_DMA
> + help
> + This selects the RDA Micro Secure digital and Multimedia card
> interface. The
> + controller supports SD/SDIO/MMC interface.
> + If you have a board with RDA SoC and it uses this interface, say Y or
> M here.
> +
> + If unsure, say N.
...
> +};
> +MODULE_DEVICE_TABLE(of, rda_mmc_dt_ids);
> +
> +static struct platform_driver rda_mmc_driver = {
> + .probe = rda_mmc_probe,
> + .remove = rda_mmc_remove,
> + .driver = {
> + .name = "rda-mmc",
> + .probe_type = PROBE_PREFER_ASYNCHRONOUS,
> + .of_match_table = rda_mmc_dt_ids,
> + },
> +};
> +module_platform_driver(rda_mmc_driver);
> +
> +MODULE_AUTHOR("Dang Huynh <dang.hu...@mainlining.org>");
> +MODULE_LICENSE("GPL");
> +MODULE_DESCRIPTION("MMC/SD driver for RDA platform");
> +MODULE_ALIAS("platform:rda-mmc");
You should not need MODULE_ALIAS() in normal cases. If you need it,
usually it means your device ID table is wrong (e.g. misses either
entries or MODULE_DEVICE_TABLE()). MODULE_ALIAS() is not a substitute
for incomplete ID table.
>
Best regards,
Krzysztof
