Linux-Hardware Digest #66, Volume #13 Sun, 18 Jun 00 20:13:06 EDT
Contents:
Re: yamaha cdrw ERROR MESSAGES! help (Dances With Crows)
Re: Logitech Cordless Wheelmouse Problem (Florian E.J. Fruth)
Re: Can't use "setserial" command to setup modem. ([EMAIL PROTECTED])
Re: mount (Vilmos Soti)
ls120 and linux 2.2.x? (Tim Kelley)
Re: Books (Faheem Mitha)
Re: Adaptec AHA1520B SCSI card problems ("Nathan Appleton")
Re: Tape backup: tar versus dump (Mark Bratcher)
Re: Water cooling system ("Tom Brinkman")
Networking glitch: What's Up? (David Steuber)
Re: Canon BJC-5000 printer (John Hong)
configuration nightmare (Julie Churchwell)
Linux and TV output ([EMAIL PROTECTED])
Re: ls120 and linux 2.2.x? (Edward Lee)
Re: Tape backup: tar versus dump ([EMAIL PROTECTED])
USB scanner? (Blackberry)
Re: USB scanner? (Edward Lee)
Re: HP DeskJet support (Julie Churchwell)
Re: HP DeskJet support (Julie Churchwell)
Re: configuration nightmare (Jim Conner)
----------------------------------------------------------------------------
From: [EMAIL PROTECTED] (Dances With Crows)
Subject: Re: yamaha cdrw ERROR MESSAGES! help
Date: 18 Jun 2000 15:27:19 EDT
Reply-To: [EMAIL PROTECTED]
On Sun, 18 Jun 2000 18:45:55 GMT, J. Roe
<<8ij5d1$93e$[EMAIL PROTECTED]>> shouted forth into the ether:
> Hi,
>I just installed redhat 6.2 on my new box and I have a yamaha cdw8424ez
>(IDE). I am getting this constant error set to my log file:
>
>ATAPI device hdc:
> Error: Not ready -- (Sense key=0x02)
This is because the automounter is running, attempting to access your CD
every second to see if there's a disk in it. Misguided feature, that, and
bloody annoying. There should be a way to turn off automounting from the
GNOME control panel, but that didn't work for the last person whom I told
to try that. He compiled a kernel without automounter support, at which
point the problem went away.
>Also, when I do have a disk in the cd drive and I do:
>[janine@localhost janine]$ dmesg | grep ^hd
>hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
>hdc: packet command error: error=0x00
I get similar errors from my Philips 460RW. Its problem seems to be that
when you insert a CD, the drive spends about 15 seconds deciding whether
the disk is a CD-ROM/burned CD-R, a blank CD-R, a blank CD-RW, or a burned
CD-RW, and adjusting its gain control/laser power settings for each
case. Any attempts to access the drive during this time result in errors
like the above. After that, it works fine.
If you want to use your drive to its full potential, go read the
CD-Writing HOWTO: http://linuxdoc.org/HOWTO/CD-Writing-HOWTO.html
--
Matt G / Dances With Crows /\ "Man could not stare too long at the face
\----[this space for rent]-----/ \ of the Computer or her children and still
\There is no Darkness in Eternity \ remain as Man." --David Zindell "So did
But only Light too dim for us to see\ they become Gods, or Usenetters?" --/me
------------------------------
From: Florian E.J. Fruth <[EMAIL PROTECTED]>
Subject: Re: Logitech Cordless Wheelmouse Problem
Date: Sun, 18 Jun 2000 21:23:55 +0200
gbass
wrote in <[EMAIL PROTECTED]>
> I have many problems with my Logitech Cordless Wheelmouse. It is very
> crazy. It goes everywhere on the desktop without your command and it opens
> menu, or closes windows, always without your command.
> I tried a lot of parameters but with no effets.
> I tried with a Microsoft Intellimouse, but it is the same.
> The /etc/X11/XF86config seems to be well conigurated. I tried many
> protocols (Microsoft-imps2-ps2-MouseSystems...), I tried
> device /dev/psaux, /dev/gpmdata...But nothing resolved my problem.
i've got the same problem. normally my mouse stops in the right upper
edge ;-(
but i found a solution (for me so try it out): just move up the mouse
wheel...
fejf
------------------------------
From: [EMAIL PROTECTED]
Subject: Re: Can't use "setserial" command to setup modem.
Date: Sun, 18 Jun 2000 20:09:53 GMT
Reply-To: [EMAIL PROTECTED]
If the modem is 56K it will be a 16550A uart. If it was accessible
under Corel then it is not a winmodem.
It seems to be reocgnized since it can dial, if not with any success.
Try seterial with all the values and see if that helps.
good luck!
On Sat, 17 Jun 2000 16:30:06 GMT, James <[EMAIL PROTECTED]> wrote:
>Hi,
> I have an internal ISA Rockwell modem, I realise it could be a winmodem
>although I have my doubts because I used to use Corel linux and it worked
>fine.
> I am now running Mandrake 7.0 and cannot manage to setup my modem. If I
>log in and load Kppp and click connect it will initialise, dial very
>slowly and hang up. If I try to reconnect It says "Sorry the modem doesn't
>respond."
> I also tried to set it up with the "setserial /dev/ttyS2 autoconfig"
>command but I get a message saying "Device or resource busy."
> I then tried doing it the long way with "setserial" but I did not know
>what value to put for "uart" how do I find this out?
> How can I get my modem to work? And why does linux think that it is
>busy?
>
>My computer;
>Cyrix 266
>64Mb RAM
>Mandrake 7.0
>Dual boot with Windows 98
------------------------------
Crossposted-To: alt.os.linux,comp.os.linux.setup
Subject: Re: mount
From: Vilmos Soti <[EMAIL PROTECTED]>
Date: Sun, 18 Jun 2000 20:12:00 GMT
"cOn" <[EMAIL PROTECTED]> writes:
> This is a multi-part message in MIME format.
Please don't post this junk. Post text only.
> does anyone know how to mount a win98 partition on RH 5.2?
> I tried both the
> mount -t msdos /dev/hd* /mnt
> and
> mount -t vfat /dev/hd* /mnt
Specify the exact device.
mount -t vfat /dev/hda1 /mnt
for the first partition on your first disk if Windows is there.
Vilmos
------------------------------
From: Tim Kelley <[EMAIL PROTECTED]>
Subject: ls120 and linux 2.2.x?
Date: Sun, 18 Jun 2000 15:56:58 -0500
Has anyone gotten this to work?
I have an LS120 and cannot use it either as a floppy or as a
superdisk.
I've tried the "ide_floppy" module and it does not work ...
------------------------------
From: [EMAIL PROTECTED] (Faheem Mitha)
Crossposted-To: alt.os.linux.mandrake,alt.os.linux.suse
Subject: Re: Books
Date: Sun, 18 Jun 2000 21:21:47 GMT
On Fri, 16 Jun 2000 19:02:44 GMT, Faheem Mitha <[EMAIL PROTECTED]> wrote:
>2) Michael Kofler: Linux: Installation, Configuration, Use.
>(1999,Addison-Wesley)
>
>This is probably the book I find myself referring to most
>frequently. It is relatively modern and up to date, and has lots of
>software specific information which I find useful. It is good for
>telling you what is out there. (For example, I first learnt of the
>existence of slrn by reading this book). It is also basically a user's
>manual. Somebody said in this thread that a new edition is coming
>out. If true this is good news. You may want to check when the new edn
>is coming out and wait for it if it is soon.
I just thought I should add that I checked with the person who said
there would be a new edition, and apparently it is a new German
edition that is coming out. As far as I could discover, there are no
plans for a new English edition. But I didn't contact Kofler directly,
which would be the best way of finding out for certain.
Faheem.
------------------------------
From: "Nathan Appleton" <[EMAIL PROTECTED]>
Subject: Re: Adaptec AHA1520B SCSI card problems
Date: Sun, 18 Jun 2000 14:27:04 -0700
"mark carroll" <[EMAIL PROTECTED]> wrote in message
news:8igrgr$5r9$[EMAIL PROTECTED]...
> Thanks! I now actually have it working as a module. Setting the
> options as I was doing may not have been working correctly, as putting
> the options into /etc/modules.conf and using modprobe instead of
> insmod seems to be working. (-: So, anyone else who has problems,
> I'm happy to mail bits of my setup.
You ought to post your comments and any tips you found helfpul back to Linux
Hardware Database (http://www.linhardware.com/db/dispproduct.php3?DISP?614).
------------------------------
From: Mark Bratcher <[EMAIL PROTECTED]>
Crossposted-To: comp.os.linux.misc
Subject: Re: Tape backup: tar versus dump
Date: Sun, 18 Jun 2000 17:56:06 -0400
Craig McCluskey wrote:
>
[snip]
>
> How can one decide between tar and dump? Both have terse man pages (what
> do you expect? :-) ) but dump's seems more inscruitable than tar's. I
> know
> what tar does (and how to write a short shell script to make it a
> proper backup utility), but I don't really have a handle on dump.
>
> In reading dump's man page, I find it backs up either filesystems or
> directories. In backing up directories, it seems to work like tar.
> In backing up filesystems, I understand that it works on a partition-by-
> partition basis. I have been told that in doing so, it makes an image of
> what is on the partition, but have seen no documentation that describes
> what's exactly going on.
These are just my opinions...
As you allude to later in your note, dump is also implicitly aware of
backup 'levels', which it tracks through the /etc/dumpdates.log file.
You could write a script that caused tar to do something like this, but
dump does it for you automatically.
I prefer dump to tar because of the backup levels, and the companion to
dump (which is 'restore') allows you to dynamically select files to
restore by traversing a directory tree. Whereas with tar if you want to
restore something, you would keep a log of verbose tar output at the
time you backed up, then find the file in the list and restore that when
you wanted to restore it. In other words, the dump/restore is a little
more backup system oriented, whereas tar is more generically an
archiving tool (as is cpio).
I think I understand why the dump manual page recommends Tower of Hanoi
scheme with the levels, and why there are ten levels. First, there are
actually 3 types of backups you might want to do: full, incremental, or
differential. Incremental backs up everything that is new/changed since
the last backup of any kind. Differential backs up everything that is
new/changed since the last full backup. To get a full backup with dump,
you use level 0. To get an incremental backup, you use one level higher
than the previous. For differential backup, you use one level higher
than the level of the backup that you want to diff from.
So if you want to do a string of incremental backups, each incremental
from the previous, you need a new level for each one. Having levels 0
through 9 gives you one full and 9 incrementals. The "Towers of Hanoi"
scheme essentially gives you a sequence of incrementals and
differentials that balance efficiency of backup data quantity with how
many backup sessions do you have to access if you want to restore
everything.
I rattled this of the top of my head, so I probably goofed something up
somewhere in the explanation, but you get the idea...
--
Mark Bratcher
mailto:[EMAIL PROTECTED]
=========================================================
Escape from Microsoft's proprietary tentacles: use Linux!
------------------------------
From: "Tom Brinkman" <[EMAIL PROTECTED]>
Subject: Re: Water cooling system
Date: Sun, 18 Jun 2000 17:41:31 -0600
In article <[EMAIL PROTECTED]>, Simon Lemieux
<[EMAIL PROTECTED]> wrote:
> Hi,
> I currently have one Celeron 433 which is Always functioning at
> 100% of
> capacity ( i always have a few animation renders of povray runing
> with low priority)... when the CPU is not in use it's at 38C and
> when it's at 100% capacity it's at 40-42C... I have a fan on the
> CPU which expulse the heat out into the room... That's fine...
> but the room in which the heat is expulsed is actually my
> bedroom... and this summer it's kind of real hot in it...
I run a p3-450 oc'd to 608 with the vcore at 2.2volts. It wants
to run hot. It idles at ~25C, 'cpuburn' never gets it over 43C. I
keep my room at ~ 80F for health reasons. Still I have no heat related
problems with my highly oc'd system. Basically the cooler the better,
but < 50C internal core temps at _extreme_ stress is OK.
If the temps you cite are read from the celery's internal diode,
they're OK. If they're from a probe (thermistor), they're too high.
Add 10 to 15C to probe temps, no matter how well placed, to approximate
internal core temps. Search 'sensors' at Freshmeat for monitoring
hardware temps/voltages/fans. I use Khealthcare, older version for
the standard winbond chip on my Soyo 6ba+III (doesn't need lm_sensors)
The heatsink on the cpu has to sit firmly, flat on it, with a thin
layer of thermal grease (Radio Shack) on the cpu. If the heatsink
came with a thermal pad, scrape it off first. Case ventilation
should be provided to maintain as near to room temp inside the case
as possible.
Cpu usage at 100% is not created equal. I've never found a program
better than 'cpuburn or BXburn' to acid test cooling. Check out:
http://users.ev1.net/~redelm/
There's nothing you say you're doing that would necessitate the
difficulty and risk that water cooling involves.
--
~~ Tom Brinkman [EMAIL PROTECTED]
------------------------------
Crossposted-To: comp.os.linux.misc,comp.os.linux.networking
Subject: Networking glitch: What's Up?
From: David Steuber <[EMAIL PROTECTED]>
Date: Sun, 18 Jun 2000 22:59:59 GMT
I have the Gateway Solo 5150 laptop computer running kernel 2.2.16 and
pcmcia-cs 3.1.16. Occasionally, when I am xfering data over the
network ( 3COM 575B pcmcia NIC ), the networking services freeze up
quite hard. The only cure is to open up cardmanager and reset the
NIC.
david@solo:> /sbin/lsmod
Module Size Used by
3c575_cb 19948 2
cb_enabler 2280 2 [3c575_cb]
ds 6728 2 [cb_enabler]
i82365 23612 2
pcmcia_core 47680 0 [cb_enabler ds i82365]
Either there is a bug in pcmcia-cs, the driver for the NIC, or the NIC
has a hardware bug. How do I find out which it is? I suppose the bug
could also be in the kernel or NFS.
This problem has existed for all earlier kernels that I have used in
the 2.2.x and 2.0.36 series. I have used earlier versions of
pcmcia-cs as well. In some cases, I used the versions as they came
from SuSE, and others I have been using my own builds. I am currently
running SuSE 6.2 and my own compiled kernel and pcmcia-cs.
The compiler makes no difference either.
This bug has a high probability of occuring when I am listening to
music over the lan. My other machine has a larger HD, so I keep my
mp3 files there, but I occasionally play them on the laptop and listen
with headphones. I use NFS to mount the disks from the other machine.
I have on occasion moved large amounts of data over the network, using
NFS, without problem. This is one of those 'intermitent' bugs.
Any useful suggestions that help track down and kill the culprit will
be gratefully accepted.
--
David Steuber | Hi! My name is David Steuber, and I am
NRA Member | a hoploholic.
All bits are significant. Some bits are more significant than others.
-- Charles Babbage Orwell
------------------------------
From: [EMAIL PROTECTED] (John Hong)
Subject: Re: Canon BJC-5000 printer
Date: 18 Jun 2000 23:09:41 GMT
Joel Hernandez ([EMAIL PROTECTED]) wrote:
: I was wondering if anyone is able to install and print with the
: BJC-5000 printer.
Check out http://www.easysw.com
They have support for it, but it will cost at the least $49.95 US
to get it.
------------------------------
From: Julie Churchwell <[EMAIL PROTECTED]>
Subject: configuration nightmare
Date: Sun, 18 Jun 2000 23:32:09 GMT
Hi everybody,
I hope there's a configuration guru in your midst, because I am lost. So
many problems I don't truly know where to start. I would like to get my
printer working, and my sound card, then on to a scanner and a zip
drive, and maybe later we could tackle a network and the and, and,
and,,,, Maybe we can just start with the printer? :)
Here's what I had----the link below leads to the page which lists the
complete system as it was when I bought it, except for that it is now
running Mandrake (The distribution is listed both as 6.1 and 6.5 so I
guess they couldn't make up their minds) instead of Windows.
http://assist.acer.com/public/system/91AA772002.htm
To this I have upgraded the Video to 2 meg
The Ram to 128 meg
Replaced the CDROM with a HI Val Changer that holds 4 disks, running on
the 2nd IDE channel. Presently only 1 bay works, under Linux. (I can
live with that)
Added a Western Digital Hard Drive as master, with the Hard disk that
came with it as slave, everything ok there.
Added a PCI NIC Card which works just fine using IRQ 11, and is hooked
up to a cable modem to the AT&T@home network, which is working fine till
I mess with things and try to make other stuff work.
I don't care about the joystick or midi or stuff like that but I need to
get the modem working so I can use this machine to answer the phone. In
the end this computer is destined to be a firewall and a telephone
answering machine and it will serve a few very small infomercial type
pages from the apache web server. Printing and faxing need to work, and
my parallel port zip drive was the plan for backups. Very light duty.
Anyway, the Magic S23 PnP Sound Card doesn't work and the modem doesn't
work. See Data Below
The Printer which is a HP DeskJet 722C, does not work (the spooler seems
to think it is working, according to the message found in the spooler
directory).
Additional Information
======================
S23 Resources Assigned with systems
91.AA772.001 & 91.AA772.002 under Windows 95
I/O Address Device Usage
=========== ============
0534-0537 Acer Magic S23 PnP Audio System CODEC
0388-038B Acer Magic S23 PnP Audio System CODEC
0220-022F Acer Magic S23 PnP Audio System CODEC
0110-0117 Acer Magic S23 PnP Audio System Control
Registers
0200-0207 Game Port Joystick
0330-0331 MPU-401 Compatible
IRQ Usage
05 Acer Magic S23 PnP Audio System CODEC
09 MPU-401 Compatible
DMA Assignment
00 Acer Magic S23 PnP Audio System CODEC
01 Acer Magic S23 PnP Audio System CODEC
Here are the original Windows Configuration files:
AUTOEXEC.BAT
============
@echo off
path=c:\windows;c:\windows\command;c:\windows\system
loadhigh doskey
c:\windows\CS32MIX /M=15,15 /W=15,15 /L=1,1 /X=1 /F=15,15
/C=1,1 /I=X
set blaster=A220 I5 D1 T4
if exist c:\restore.bat c:\restore.bat
CONFIG.SYS
==========
FILES = 50
device=c:\windows\himem.sys
device=c:\windows\emm386.exe noems
dos=high, umb
device=c:\windows\cs4232c.exe /W
device=c:\dosdrvrs\d910v310.sys /d:CDIDE01
Anyway folks I know this is a lot of reading and if any of you has made
it this far my hat is truly off to you! I can quickly get any other
information on this system that you need, but I have been working on
this for a couple of months now and there is just something here that I
do not understand no matter how many times I read it. I am stumped!
Julie
------------------------------
From: [EMAIL PROTECTED]
Subject: Linux and TV output
Date: Sun, 18 Jun 2000 19:40:07 -0500
Hi,
Has anyone succeded using the TV output of
an ATI Xpert@play video card? I am thinking
of using a TV set to surf the web in my
"Lazyboy" :) I've heard rumours that it worked
in text mode but haven't heard anything about
X...
So, if someone has succeeded using it in
X, I would appreciate to know the details of
their setup (refresh frequencies, resolution,
etc). And if there is anything to change in
the setup files to enable the TV output.
TIA!
------------------------------
From: Edward Lee <[EMAIL PROTECTED]>
Subject: Re: ls120 and linux 2.2.x?
Date: Sun, 18 Jun 2000 08:10:36 -0700
I have it on my secondard master (/dev/hdc) with Linux 2.4.0. Did you
mount it with /dev/hd? instead of /dev/fd?.
Tim Kelley wrote:
> Has anyone gotten this to work?
>
> I have an LS120 and cannot use it either as a floppy or as a
> superdisk.
>
> I've tried the "ide_floppy" module and it does not work ...
------------------------------
From: [EMAIL PROTECTED]
Crossposted-To: comp.os.linux.misc
Subject: Re: Tape backup: tar versus dump
Date: 18 Jun 2000 19:27:30 -0400
[Snipped previous discussion of dump vs tar for linux]
One problem I noticed it that Linux dump ONLY dumps complete filesystems, even
though the man page says it dumps filesystems and directories!
I've got everything on one partition (/usr /home /etc...), but I only
want to backup /home. Is there an easy way to do this?
BTW, I also discovered that TAR has a 2GB file limit!!! So I can't use
this one either...
Any help is appreciated,
Richard
------------------------------
From: Blackberry <[EMAIL PROTECTED]>
Subject: USB scanner?
Date: 18 Jun 2000 15:44:00 -0700
I've got a USB scanner (HP ScanJet 3300Cse) and I was wondering what the support
is like in Linux. I know that USB support is built into later kernels, but the
howto only lists how to get it working with printers, mice, keyboards, and hubs.
What do I need to do? Would SANE be able to recognize it if I got a USB to SCSI
adapter and plugged it into my SCSI card?
====================
"It's enough to make you wonder sometimes if you're on the right planet."
-- Frankie Goes to Hollywood
Brian -- [EMAIL PROTECTED] -- http://www.europa.com/~lepus
------------------------------
From: Edward Lee <[EMAIL PROTECTED]>
Subject: Re: USB scanner?
Date: Sun, 18 Jun 2000 08:19:47 -0700
Check out the 2.4 Doc/usb/scanner-hp-sane.txt. USB is the main reason for me to go
2.4.
Blackberry wrote:
> I've got a USB scanner (HP ScanJet 3300Cse) and I was wondering what the support
> is like in Linux. I know that USB support is built into later kernels, but the
> howto only lists how to get it working with printers, mice, keyboards, and hubs.
> What do I need to do? Would SANE be able to recognize it if I got a USB to SCSI
> adapter and plugged it into my SCSI card?
>
> --------------------
> "It's enough to make you wonder sometimes if you're on the right planet."
> -- Frankie Goes to Hollywood
> Brian -- [EMAIL PROTECTED] -- http://www.europa.com/~lepus
------------------------------
From: Julie Churchwell <[EMAIL PROTECTED]>
Subject: Re: HP DeskJet support
Date: Sun, 18 Jun 2000 23:58:03 GMT
Do you know that for a fact DG? I have lost 2 months of my life trying to get
my 722C working under Linux, so far nothing. I am extremely upset for the cost
of all this lost time. I would have been far and away ahead to go out and buy
another printer, and I may yet have to.
Julie
DG wrote:
> josh wrote:
> >
> > Espen Ekeroth wrote:
> > >
> > > Just a simple question:
> > >
> > > Is the HP DeskJet 710 C or 840 C supported ?
> > >
> > > In the RedHat documentation it looks like all HP DeskJet/DeskJet Plus is
> > > supportet, but just want to be sure before buing one.
> > >
> > >
> > > Espen
> > >
> > > mailto:[EMAIL PROTECTED]
> > >
> > No 710 is NOT supported
> > dont know about 840
>
> I don't think there are any consumer-brand HP printers that are
> "supported" under Linux. However, any PCL printer (the 840) will work
> reasonably well, and all postscript printers. Even the PPA printers
> (710 for example) can be made to work decently.
>
> --
> DG (remove the Zs)
> [EMAIL PROTECTED]
------------------------------
From: Julie Churchwell <[EMAIL PROTECTED]>
Subject: Re: HP DeskJet support
Date: Mon, 19 Jun 2000 00:09:42 GMT
That works with some of them, just like you said, I did the same thing with
using some of the drivers out of the 500 series for a 600 series printer. Not
with the ones in 700 series, though, because they use a different language,
and some were designed to work only with Windows. I realize this is a little
simplistic since I was vague about the model numbers but if you look into it
you will see that I am mostly right. It's not worth the pain baby! My 722C is
a wonderful little printer under Windows, and a boat anchor under Linux.
Supposedly my 722C can use 710C drivers so you know they are probably the much
the same.
Julie
[EMAIL PROTECTED] wrote:
> In <[EMAIL PROTECTED]>, josh <[EMAIL PROTECTED]> writes:
>
> >> Is the HP DeskJet 710 C or 840 C supported ?
> >>
> >> In the RedHat documentation it looks like all HP DeskJet/DeskJet Plus is
> >> supportet, but just want to be sure before buing one.
> >>
> >>
> >> Espen
> >>
> >> mailto:[EMAIL PROTECTED]
> >>
> >No 710 is NOT supported
> >dont know about 840
>
> I'm not sure what 'supported' implies here. I have an HP 880C. When
> I installed Mandrake 7.0 it thought I had a Deskjet 500, but as there
> was a 600C series in the list, I chose that.
> It all seems to work OK, so if your distribution doesn't explicitly
> list your model, just go for the nearest.
>
> - Richard Kimber
>
> Political Science Resources
> http://www.psr.keele.ac.uk/
------------------------------
From: Jim Conner <[EMAIL PROTECTED]>
Subject: Re: configuration nightmare
Date: Mon, 19 Jun 2000 00:09:45 GMT
Go to the following web address. You can find most drivers for most
hardware. If it's more that a driver problem, we will need more info on
the printer.
http://www.linhardware.com/
P.S. If this doesn't help, don't lose the address, it will come in handy
later.
Jim
Julie Churchwell wrote:
> Hi everybody,
>
> I hope there's a configuration guru in your midst, because I am lost. So
> many problems I don't truly know where to start. I would like to get my
> printer working, and my sound card, then on to a scanner and a zip
> drive, and maybe later we could tackle a network and the and, and,
> and,,,, Maybe we can just start with the printer? :)
>
<snippage>
> Julie
------------------------------
** FOR YOUR REFERENCE **
The service address, to which questions about the list itself and requests
to be added to or deleted from it should be directed, is:
Internet: [EMAIL PROTECTED]
You can send mail to the entire list (and comp.os.linux.hardware) via:
Internet: [EMAIL PROTECTED]
Linux may be obtained via one of these FTP sites:
ftp.funet.fi pub/Linux
tsx-11.mit.edu pub/linux
sunsite.unc.edu pub/Linux
End of Linux-Hardware Digest
******************************
