Linux-Hardware Digest #192, Volume #13 Fri, 7 Jul 00 13:13:07 EDT
Contents:
Re: 486 Linux setup, 250 meg HD, which distro ??? (Steve Martin)
Re: Looking for sexy embedded linux hardware (Steve Martin)
kudzu,pcmcia and sound (Darren Christie)
Re: Creative Soundblaster PCI128 (moonie;))
Re: Add SCSI tape drives (Myra Hager)
Tape Drive Support (Mark Feller)
Promise FastTrak 100 (Baron Chandler)
Re: Linux & HP LaserJet 3150 (Toon Moene)
Is Brainbench Legitimate? ("mmm007")
Re: Linux home server: Clean-slate hardware plan? (Rod Smith)
GPIB-PCMCIA + DAQ-PCMCIA (friedel_hacker)
GPIB-PCI and DAQ-PCI (friedel_hacker)
Toshiba Sattelite 1605 CDS (Fred)
Re: intel 810 onboard graphics card (Clarence Wilkerson)
Re: IEEE 488 driver (friedel_hacker)
Re: Toshiba Sattelite 1605 CDS (Tony Curtis)
Re: IEEE488? (friedel_hacker)
Re: IEEE488? (friedel_hacker)
Re: Add SCSI tape drives (James Knowles)
Re: Tape Drives - how do you backup? (James Knowles)
mysterious noise from PC speaker (Warren Gross)
q? compaq presario 1610 nb ? ("zada.zada")
IBM PC Server 300? ("Bill Crocker")
Re: Getting Redhat on 12 MB ("Mark Langsdorf")
----------------------------------------------------------------------------
From: Steve Martin <[EMAIL PROTECTED]>
Crossposted-To: comp.os.linux.advocacy,comp.os.linux.setup
Subject: Re: 486 Linux setup, 250 meg HD, which distro ???
Date: Fri, 07 Jul 2000 08:15:34 -0400
Jim Cameron wrote:
> >hacked every 5 minutes your on the internet. Choose Slack, Choose sleepless
> >nights tearing your hair out, Choose Debian, Choose never being able to use
>
> I use Slack, and I have LOTS of hair. 8-)
I started out with Slackware, and I have *no* hair! ('Course,
I'm 45 years old, too... <g>)
------------------------------
From: Steve Martin <[EMAIL PROTECTED]>
Subject: Re: Looking for sexy embedded linux hardware
Date: Fri, 07 Jul 2000 08:19:36 -0400
Just a quick note in this vein, there was an announcement
a short while back on comp.os.linux.announce about a new
USENET newsgroup that may interest the original poster of
this thread. The group is comp.os.linux.embedded, and it's
apparently just starting up. It might be something you'd
want to check into.
------------------------------
From: Darren Christie <[EMAIL PROTECTED]>
Crossposted-To: comp.os.linux.setup,comp.os.linux.portable,comp.os.linux.misc
Subject: kudzu,pcmcia and sound
Date: Fri, 7 Jul 2000 09:13:27 +0100
Reply-To: [EMAIL PROTECTED]
I have Redhat 6.1 installed on a Toshiba Tecra 8100, however when
booting kudzu has decided not to detect new hardware. After doing some
digging around I found that hwconf was corrupted. So I copied this from
an identical configured system. Rebooted and still the same results. So
I am lost at what to do next to resolve this, so any suggestions would
be greatly received.
The other problem I have is configuring sound on the above laptop,
I managed to get sound to work using alsa 0.5.8, and promptly on
rebooting to test, pcmcia wouldn't start up, but I had sound.
Now for some reason pcmcia is back, but now sound won't work! I get
that the device is busy. I thought it might be a conflict between pcmcia
and the sound hardware (ymfpci) but I can use both together no problem
under Windoze98. So please could you help on this as well?
If you could copy answers to my e-mail, as the work newsgroup feed only
picks up once a day.
Thanks
Darren
------------------------------
From: moonie;) <[EMAIL PROTECTED]>
Crossposted-To: comp.os.linux
Subject: Re: Creative Soundblaster PCI128
Date: Fri, 7 Jul 2000 10:26:20 -0400
On Thu, 06 Jul 2000, sandrews wrote:
>"moonie;)" wrote:
>>
>> On Sat, 10 Jun 2000, Klaus Syttkus wrote:
>> >Hi,
>> >
>> >a hint: There seem to be two flavours of PCI128 out there. One uses a
>> >es1370, the other one es1371.
>> >Have you used lspci?
>> >
>> >Good luck,
>> >
>> >Klaus.
>>
>> I have found that people with the es1370 tend to have no problem at all. The
>> ones with es1371 tend to have trouble. My PCI128 was an early one and is
>> es1370 and has always worked perfectly. Not trying to dissuade you just
>> letting you know that if it is an es1371 you may not be able to get it working.
>> --
>> moonie ;)
>>
>
>I have an es1373 late model card that didn`t work without the OSS
>drivers.
>The card will now work with RH 6.2 and Suse 6.4. From what I understand
>the
>es1371.o module has been changed to accommandate the later cards.
>From SuSe conf.modules:
>
>#alias char-major-14 off
>#alias sound off
>#alias midi off
>
>then
>
>###############################################################################
># module : es1371.o Creative Ensoniq 1371 Chipsatz (-->
>PCI64/128)
>#
># Supported cards :
>#
># Creative Labs PCI64/128
>#
># Documentation availabke at
>/usr/src/linux/Documentation/sound/es1371 and
># /usr/src/linux/drivers/sound/es1371.c .
>#
>alias char-major-14
>es1371 options es1371 joystick=0x200
>###############################################################################
>
>Makes mine work.
With your permision (hopefully) I will save this and use it when this question
comes around again. For all those who couldn't get theirs to work I thank you.
--
moonie ;)
Registered Linux User #175104
------------------------------
From: Myra Hager <[EMAIL PROTECTED]>
Subject: Re: Add SCSI tape drives
Date: Fri, 07 Jul 2000 14:24:42 GMT
There are scsi tape devices listed in /dev (st0,st1, etc). but if i
use an mt command with any of the device names listed, it says NO
DEVICE FOUND.
I went to my kernel configurator and there is a scsi host adaptor
listed in the module list. But how do i deterine if tape support is
compiled in and how do I check to see if added to my scsi chain. I
tried using makedev and it indicated that wasn't a valid command.
Sorry to be so confused but appreciating your help.....
In article <[EMAIL PROTECTED]>,
"Andrew E. Schulman" <[EMAIL PROTECTED]> wrote:
> > > I need to add 2 SCSI tape drives to an a red hat server. I am
used to
> > > the SCO command mkdev tape to view, change, or add scsi tape
devices.
> > > I have looked at linuxconf and mknod and neither of these seems
to be
> > > what I need. Can someone please point me in the right direction
to do
> > > this. Thanks.
> >
> > All you need to do is make sure your kernel has tape support
compiled in, and
> > then you just need to add the tape drive to your scsi
chain, /dev/nst0 is the
> > first tape drive (no rewind moe), and /dev/nst1 is the second. If
you want the
> > tape drive to rewind after use, then use /dev/st0 and /dev/st1
instead. By
> > default, tape block sizes are fixed at 512 bytes, unless you use
the "mt"
> > command to change the defaults.
>
> And in case those devices don't exist, try e.g.
>
> MAKEDEV st0
>
> to create them, or else find the major and minor devices numbers and
use
> mknod.
>
Sent via Deja.com http://www.deja.com/
Before you buy.
------------------------------
From: Mark Feller <[EMAIL PROTECTED]>
Subject: Tape Drive Support
Date: Fri, 07 Jul 2000 09:35:10 -0500
This is a multi-part message in MIME format.
==============AD4D3891BCC58A9E4D9377D2
Content-Type: text/plain; charset=us-ascii
Content-Transfer-Encoding: 7bit
Can Linux be used with any of Onstream's offerings?
Thanks,
Mark
==============AD4D3891BCC58A9E4D9377D2
Content-Type: text/x-vcard; charset=us-ascii;
name="mfeller.vcf"
Content-Transfer-Encoding: 7bit
Content-Description: Card for Mark Feller
Content-Disposition: attachment;
filename="mfeller.vcf"
begin:vcard
n:Feller;Mark
tel;fax:756-455-0339
tel;work:765-455-0444
x-mozilla-html:FALSE
org:M Gottlieb Associates, Inc.
adr:;;608 East Boulevard;Kokomo;Indiana;46902;
version:2.1
email;internet:[EMAIL PROTECTED]
title:Field Application Engineer
fn:Mark Feller
end:vcard
==============AD4D3891BCC58A9E4D9377D2==
------------------------------
From: Baron Chandler <[EMAIL PROTECTED]>
Subject: Promise FastTrak 100
Date: 7 Jul 2000 14:47:31 GMT
I just bought a Promise FastTrak 100 after seeing that the new 100 card is
supported in 2.4. So I unwrap my nice new box and plunk it in. Mandrake
wouldn't even install. Figuring that the card just didn't work with 2.2, I took
it out and installed 'drake on a dinky 2gb seagate (SLOW seagate) then built
2.4 with the reiserfs patch.
With the 2.2 kernel installed where I could see what happened, I put the card
back in. I booted the kernel. It'd see my on-board ide controller fine
(standard 2 channels). Then freeze - hard freeze - push the power button for 5
seconds freeze. No messages or anything.
With the 2.4 kernel, it'd see the on-board ide controller AND the PDC20267
cards. It did its "ide.c" part of the initialization -
PDC20267: Chipset revision 2
PDC20267: Not 100% native mode: will probe irqs later
Then paused for about a secondd, then the "pdc202xx.c" part of the init -
PDC20267: (U)DMA Burst bit enabled Primary MASTER mode Secondary MASTER mode
Then:
PDC20267: neither IDE port enabled (BIOS)
and the same old dead freeze. Nothing further.
I've tried various kernel parameters to no avail. I DID boot to DOS and
fdisk/format the array and it worked fine. All result in the same freeze. Any
ideas or suggestions? I feel like I am missing a small detail to fix
everything, but a deja/altavista search and reading the driver sources didn't
reveal anything that worked. Am I on crack? Is this just not supported yet
even though the chipset is?
Thanks,
Baron.
------------------------------
From: Toon Moene <[EMAIL PROTECTED]>
Subject: Re: Linux & HP LaserJet 3150
Date: Fri, 07 Jul 2000 16:42:56 +0200
Grant Taylor wrote:
> Toon Moene <[EMAIL PROTECTED]> writes:
>
> > I just bought a Hewlett Packard LaserJet 3150
>
> Bummer. This device is reported not to work at all. See
> http://www.linuxprinting.org/show_printer.cgi?recnum=266185
>
> HP's Windows driver provides a slightly buggy PCL emulation, so you
> could print from Linux through Ghostscript over the network to a
> Windows box, but that's rather roundabout.
:-(
> It is possible, but not likely, that this is in fact an OfficeJet-
> heritage device that does actually speak PCL. If so, you would simply
> need the userspace MLC protocol driver kit to send PCL to the printer
> in the way it expects. You can find that at http://hpoj.bstc.net/
Unfortunately, that also doesn't work - the site lists the 3150 with a
red cross - meaning: doesn't work at all (paperweight).
That'll teach me to beleive "LaserJet" will work because so many
laserjets are supported.
In fact, I'm leaning towards consumer action here - apparently, HP wants
us to believe that these devices are somehow "of the same family" of
other laserjets, but they use a completely different protocol (A
protocol that HP, according to the web site, wants to keep secret, so
there is not even a remote chance that this printer will *ever* work on
Linux).
Where's Ralf Nader when you need him ;-)
(Perhaps just requiring all non-conformant manufacturers to stamp a
large Penguin with a red cross through it as a sign that "this device
doesn't work with Linux and we're not gonna change that" is enough :-)
--
Toon Moene - mailto:[EMAIL PROTECTED] - phoneto: +31 346 214290
Saturnushof 14, 3738 XG Maartensdijk, The Netherlands
GNU Fortran 77: http://gcc.gnu.org/onlinedocs/g77_news.html
GNU Fortran 95: http://g95.sourceforge.net/ (under construction)
------------------------------
From: "mmm007" <[EMAIL PROTECTED]>
Subject: Is Brainbench Legitimate?
Date: Fri, 7 Jul 2000 11:31:42 -0400
I just took a free Brainbench Linux Administrator certification exam and
barely passed. That exam was tough. I thought it would be a joke sinces its
free. I
talked to a couple of friends and they took the exams and were surprised.
Have any of you taken these exams?
------------------------------
Reply-To: [EMAIL PROTECTED]
From: [EMAIL PROTECTED] (Rod Smith)
Subject: Re: Linux home server: Clean-slate hardware plan?
Date: Fri, 07 Jul 2000 15:36:35 GMT
[Posted and mailed]
In article <[EMAIL PROTECTED]>,
"Steve Conover, Sr." <[EMAIL PROTECTED]> writes:
> Hello Linux experts. I'm a novice who wants to network my home,
> but wants to avoid purchasing NT Server, for lots of reasons.
>
> My goal: Linux home server for three or four PC's, for sharing
> files, printers, and cable modem internet connection.
>
> Just need bare essentials for a server, and want to be sure
> everything is 100% guaranteed to work with Linux (Red Hat,
> probably).
The simplest way to do this is to buy from an outfit that produces
pre-built Linux boxes.
> Here's the configuration I'm planning; PLEASE let me know if
> anything below might give me Linux-compatibility problems...
> ------------------------------------------------------------
> Group 1: planned hardware I don't own yet:
>
> Motherboard: ASUS P2B w/ onboard Adaptec SCSI controller
> CPU: Intel P-III ~500MHz
I'm not familiar with that motherboard, but motherboards per se seldom
cause problems. Most or all Adaptec SCSI adapters are supported.
> NIC: 3COM 10/100
This will probably be fine. You can get by with less expensive models
(Linksys, NDC SOHOware, Netgear, D-Link, and others all make boards that
work well with Linux but cost less than a typical 3Com board).
> Cable, RJ-45 twisted pair (specs?)
For 100Mbps, you need Category 5 (aka "Cat5") cables. You also need a
hub or switch to link the computers together. A switch will produce
better performance, but will cost a bit more.
> Graphics card: ? (suggestions please)
For a dedicated server, get something cheap. Just about anything will
work in text mode, and most inexpensive boards will work in graphics
mode (for X). You can check at http://www.xfree86.org or any Linux
distribution's web site for lists of supported boards.
> SCSI CD-ROM drive: ? (suggestions please)
Unless you plan to use the CD-ROM drive pretty heavily, you may want to
save a few bucks and get an cheap IDE model (any drive will work). If
you do lots of CD-ROM-intensive stuff, get the one with the highest
speed you can find. I've heard that some of the multi-beam models don't
work well with Linux, though. If you do digital audio extraction (DAE;
creating .wav files from audio CDs), Plextor models have an excellent
reputation for doing flawless or near-flawless DAE.
> ------------------------------------------------------------
> Group 2: hardware I already own:
>
> Hard drive: Seagate Barracuda, Ultra-2 SCSI, 9G
> Monitor: ViewSonic 17"
> Printer1: LaserJet 5
> Printer2: Phaser 740
> Logitech keyboard, trackball
None of this should pose any problems, with the possible exception of
printer #2; I've simply not heard of it. Check
http://www.picante.com/~gtaylor/pht/printer_list.cgi for printer
compatibility information.
FWIW, I've got a book on Linux hardware that's coming out in about two
weeks. Check http://www.rodsbooks.com/hardware/ for more information.
--
Rod Smith, [EMAIL PROTECTED]
http://www.rodsbooks.com
Author of books on Linux networking & multi-OS configuration
------------------------------
Subject: GPIB-PCMCIA + DAQ-PCMCIA
From: friedel_hacker <[EMAIL PROTECTED]>
Date: Fri, 07 Jul 2000 08:47:31 -0700
GPIB and DAQ cards for PCMCIA and PCI with LINUX support are
available now!!
Please visit our website http://www.inesinc.com
or contact our support engineers under [EMAIL PROTECTED]
Best regards,
Friedel Hacker
===========================================================
Got questions? Get answers over the phone at Keen.com.
Up to 100 minutes free!
http://www.keen.com
------------------------------
Subject: GPIB-PCI and DAQ-PCI
From: friedel_hacker <[EMAIL PROTECTED]>
Date: Fri, 07 Jul 2000 08:48:16 -0700
GPIB and DAQ cards for PCMCIA and PCI with LINUX support are
available now!!
Please visit our website http://www.inesinc.com
or contact our support engineers under [EMAIL PROTECTED]
Best regards,
Friedel Hacker
===========================================================
Got questions? Get answers over the phone at Keen.com.
Up to 100 minutes free!
http://www.keen.com
------------------------------
From: Fred <[EMAIL PROTECTED]>
Subject: Toshiba Sattelite 1605 CDS
Date: Fri, 07 Jul 2000 15:52:07 GMT
Just asking before spending (what is for me) a fortune on this laptop. I
need to run X, accelerated. The XFree86 website says the chips included
in this machine are supported.
This will be my first notebook computer. I recall reading in some linux
discussions over the past few years that the biggest problem with
notebooks was the graphics. So I feel I'm safe on that front...but are
there any other problems?
Linux.com hardware compatibility lists some other Toshiba notebooks, but
not this one in particular.
Any advice would be greatly appreciated.
Thanks,
Fred
Sent via Deja.com http://www.deja.com/
Before you buy.
------------------------------
From: [EMAIL PROTECTED] (Clarence Wilkerson)
Subject: Re: intel 810 onboard graphics card
Date: 7 Jul 2000 15:55:12 GMT
Reply-To: [EMAIL PROTECTED]
There are X drivers for that chip on the intel company site.
--
Clarence Wilkerson \ HomePage: http://www.math.purdue.edu/~wilker
Prof. of Math. \ Internet: [EMAIL PROTECTED]
Dept. of Mathematics \ Messages: (765) 494-1903, FAX 494-0548
Purdue University, \
W. Lafayette, IN 47907-1395 \
------------------------------
Subject: Re: IEEE 488 driver
From: friedel_hacker <[EMAIL PROTECTED]>
Date: Fri, 07 Jul 2000 09:12:33 -0700
Hi,
which type of card do you have?
We have developed a 7210 compatible chip. You can download the
Hardware manual from following website:
http://www.GPIB2000.com
or you can buy a card from us.
All our cards for AT, PCI and PCMCIA supports LINUX.
If you have further technical questions, please contact our
support engineers under [EMAIL PROTECTED]
Best regards,
Friedel Hacker
===========================================================
Got questions? Get answers over the phone at Keen.com.
Up to 100 minutes free!
http://www.keen.com
------------------------------
From: Tony Curtis <[EMAIL PROTECTED]>
Subject: Re: Toshiba Sattelite 1605 CDS
Date: 07 Jul 2000 11:15:55 -0500
>> On Fri, 07 Jul 2000 15:52:07 GMT,
>> Fred <[EMAIL PROTECTED]> said:
> Linux.com hardware compatibility lists some other
> Toshiba notebooks, but not this one in particular.
There's a big list of laptops at:
http://www.cs.utexas.edu/users/kharker/linux-laptop/
hth
t
--
"With $10,000, we'd be millionaires!"
Homer Simpson
------------------------------
Subject: Re: IEEE488?
From: friedel_hacker <[EMAIL PROTECTED]>
Date: Fri, 07 Jul 2000 09:16:21 -0700
Yes,
all our GPIB cards for AT, PCI and PCMCIA supports LINUX.
Please visit http://www.inesinc.com
For any further questions, please visit our support engineers
under [EMAIL PROTECTED]
Best regards,
Friedel Hacker
===========================================================
Got questions? Get answers over the phone at Keen.com.
Up to 100 minutes free!
http://www.keen.com
------------------------------
Subject: Re: IEEE488?
From: friedel_hacker <[EMAIL PROTECTED]>
Date: Fri, 07 Jul 2000 09:18:59 -0700
All our GPIB cards for AT, PCI and PCMCIA supports LINUX.
Please visit http://www.inesinc.com
For any further questions concerning the GPIB-LINUX driver,
please contact our support engineers under [EMAIL PROTECTED]
Best regards,
Friedel Hacker
===========================================================
Got questions? Get answers over the phone at Keen.com.
Up to 100 minutes free!
http://www.keen.com
------------------------------
From: James Knowles <[EMAIL PROTECTED]>
Subject: Re: Add SCSI tape drives
Date: Fri, 07 Jul 2000 10:34:47 -0600
> But how do i deterine if tape support is
> compiled in and how do I check to see if added to my scsi chain.
What does it say on boot? Looking in /var/log/messages.? mine says the
following. It detects the SCSI controller, three disks, and the DAT
drive:
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.28/3.2.4
<Adaptec AIC-7890/1 Ultra2 SCSI host adapter>
scsi : 1 host.
(scsi0:0:0:0) Synchronous at 20.0 Mbyte/sec, offset 15.
Vendor: QUANTUM Model: FIREBALL ST6.4S Rev: 0F0C
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
(scsi0:0:1:0) Synchronous at 20.0 Mbyte/sec, offset 15.
Vendor: QUANTUM Model: FIREBALL ST6.4S Rev: 0F0C
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
(scsi0:0:2:0) Synchronous at 20.0 Mbyte/sec, offset 15.
Vendor: QUANTUM Model: FIREBALL ST6.4S Rev: 0F0C
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdc at scsi0, channel 0, id 2, lun 0
(scsi0:0:3:0) Synchronous at 10.0 Mbyte/sec, offset 32.
Vendor: HP Model: C1537A Rev: L708
Type: Sequential-Access ANSI SCSI revision: 02
This last entry is my SCSI DAT drive. Seeing this I know that it sees
the DAT on the SCSI chain. Later in the boot sequence it says:
Detected scsi tape st0 at scsi0, channel 0, id 3, lun 0
which tells me that the tape is ready to go. This was all off of the
stock RedHat install. I personally didn't have to diddle with anything.
--
Surround yourself with the best people you can find, delegate authority,
and don't interfere.
- Ronald Reagan, FORTUNE, September 15, 1986
------------------------------
From: James Knowles <[EMAIL PROTECTED]>
Subject: Re: Tape Drives - how do you backup?
Date: Fri, 07 Jul 2000 10:36:09 -0600
> tar cvf mydir /dev/tape
To pick nits:
tar cvf /dev/tape mydir
archive is listed first after -f, files and directories come last.
--
If at first you don't succeed...get a bigger hammer.
------------------------------
From: [EMAIL PROTECTED] (Warren Gross)
Subject: mysterious noise from PC speaker
Date: 7 Jul 2000 15:30:47 GMT
I've got a mysterious noise coming from the PC speaker
with Redhat 6.2.
It happens pretty randomly it seems, after the box has been up
(and idle) for several hours and it just starts by itself. Its a
high-pitched
note. Only shutting down seems to kill it.
Any ideas? How can I disable the speaker permanently as a work-around?
Warren
------------------------------
From: "zada.zada" <[EMAIL PROTECTED]>
Reply-To: [EMAIL PROTECTED]
Subject: q? compaq presario 1610 nb ?
Date: Fri, 07 Jul 2000 16:51:46 GMT
will linux work on this and what version is recommended?
thx!
z
<+><
.
------------------------------
From: "Bill Crocker" <[EMAIL PROTECTED]>
Subject: IBM PC Server 300?
Date: Fri, 07 Jul 2000 16:59:01 GMT
I recently acquired an IBM PC Server 300, that I want to use as a platform
to learn Linux.
Intel Pentium 60
32-MEG
1- SCSI Hard Drive, 1-GIG
6- SCSI CD-ROM Drives
Combination of ISA, PCI, and EISA slots
Any foreseeable problems, or suggestions?
Thanks,
Bill Crocker
------------------------------
From: "Mark Langsdorf" <[EMAIL PROTECTED]>
Crossposted-To: comp.os.linux.misc
Subject: Re: Getting Redhat on 12 MB
Date: Fri, 7 Jul 2000 12:06:10 -0500
"the fat heffer" <[EMAIL PROTECTED]> wrote in message
news:[EMAIL PROTECTED]...
> HI
> Does anyone know whether its possible to get redhat on to a 12mb disk
> I have heard you can recompile the kernal or something
The kernel is not the problem. The problem is glibc, which can be
upwards
of 10-15 megs all by itself.
Look for an embedded Linux distribution. Everyone and his brother is
releasing one these days. Lineo's Embedix is a good example - based on
Caldera OpenLinux 2.3. An absolute minimal configuration can be under
3 megs with Embedix.
-Mark Langsdorf
------------------------------
** FOR YOUR REFERENCE **
The service address, to which questions about the list itself and requests
to be added to or deleted from it should be directed, is:
Internet: [EMAIL PROTECTED]
You can send mail to the entire list (and comp.os.linux.hardware) via:
Internet: [EMAIL PROTECTED]
Linux may be obtained via one of these FTP sites:
ftp.funet.fi pub/Linux
tsx-11.mit.edu pub/linux
sunsite.unc.edu pub/Linux
End of Linux-Hardware Digest
******************************
