Linux-Hardware Digest #705, Volume #13 Tue, 10 Oct 00 17:13:08 EDT
Contents:
Re: Setting up SCSI harddisk... (Joshua Baker-LePain)
CDROM access locks up Redhat - adaptor card issue?
CL Video Blaster Webcam 3 Parallel port. (pogo)
Video Capture (Man)
Re: Kernel Panic (Bartek Kostrzewa)
Re: RedHat6.2 (or other) on Asus A7V Athlon system (Remi Ricard)
Zip scsi card (Remi Ricard)
Re: SB128PCI won't play under SuSE Linux 6.4 - why? (Henrik Carlqvist)
newbie: linux box hunt (Brad Friedman)
Re: RedHat6.2 (or other) on Asus A7V Athlon system (Je77)
Re: Linux on Compaq Deskpro 6000 MP System (Matt Fuerst)
UDMA controller trouble with Micronics M6Me board (Moscito)
Re: wrong hard drive info ("bluster")
Re: stcolor epson860 ("Ivan Danicic")
IDE support on Sound card for CDROM? (Roger Ehrlich)
Wheel Mouse ([EMAIL PROTECTED])
Re: Sparc/Solaris vs Intel/Linux: Webserver (Andrew Donkin)
Re: SCSI tape drive problem w/ RH 6.1 ([EMAIL PROTECTED])
Re: Adding a Windows hard drive (Mile Davidovic)
Re: Kernel Panic (Jim McDonald)
Re: SCSI tape drive problem w/ RH 6.1 (Mike)
----------------------------------------------------------------------------
From: Joshua Baker-LePain <[EMAIL PROTECTED]>
Crossposted-To: comp.os.linux.setup
Subject: Re: Setting up SCSI harddisk...
Date: 10 Oct 2000 15:16:32 GMT
In comp.os.linux.hardware Marty <[EMAIL PROTECTED]> wrote:
> I have just bought a SCSI adapter and a quantum SCSI harddisk. When I boot
> up the Linux, it can only detect the SCSI adapter. I don't know how to
> setup the SCSI harddisk. I have tried to type the following
> echo "scsi add-single-device 0 0 6 0" > /proc/scsi/scsi
This should *not* be necessary. When the driver for your card is
loaded (does this happen at bootup?), it should detect all the
devices on the chain. Actually, it should detect all devices
on the *properly terminated* chain. Check your termination. Then,
make sure that the line "alias scsi_hostadapter xxxx", where xxxx
is replaced by the driver for your card, is in /etc/conf.modules.
> echo "abc" > /dev/sga
Err, sga is a scsi Generic device. Your first SCSI hard disk should
be at /dev/sda.
First, make sure your chain is properly terminated. Then, bootup
and ensure that the device driver is loaded (you could force it
with a "modprobe xxx" at the end of /etc/rc.d/rc.local). When
the driver is loaded, ensure that it sees your hard drive, and
that it assigns it to /dev/sda.
Once all that is done, you have to perform the usual steps of partitioning
and formatting the drive. fdisk to parition it, then mke2fs to format
each partition.
And don't forget the goats...
--
Joshua Baker-LePain
Department of Biomedical Engineering
Duke University
------------------------------
Subject: CDROM access locks up Redhat - adaptor card issue?
Date: Tue, 10 Oct 2000 11:33:49 -0400
From: <[EMAIL PROTECTED]>
Hi,
I just installed a new 40 gig Maxtor hard drive and an adaptor card and now when
I try to access my cdrom, Linux locks up solid as a rock. I have tried mounting
it as a drive device and also as a scsi device, like my cdr, which does mount ok
but either option for the cdrom locks things up.
I'm running Redhat 7.0, and 2.4.0-test9 kernel.
>From my fstab:
=====
# /dev/hdb /mnt/cdrom iso9660 ro,user,noauto 0 0
# /dev/sr0 /mnt/cdrom iso9660 rw,user,noauto 0 0
# /dev/hdc /mnt/cdr iso9660 rw,user,noauto 0 0
/dev/scd0 /mnt/cdrom iso9660 ro,user,noauto 0 0
/dev/scd1 /mnt/cdr iso9660 rw,user,noauto 0 0
IDE Info
========
Main Board IDE
==============
hda drive which is not active
hdb CDROM
hdc CDR
hdd nothing connected
Maxtor Ultra ATA/100 PCI Adaptor Card
====================================
hde drive with first partion active, i.e., bootable ("C" in Win98SE>
hdf nothing connected
hdg drive with Linux installed, root at hdg9
hdf nothing connected
Appreciate any help. BTW, sorry for the cross post in setup, I meant to post
here.
Thanks
------------------------------
From: pogo <[EMAIL PROTECTED]>
Subject: CL Video Blaster Webcam 3 Parallel port.
Date: Tue, 10 Oct 2000 02:03:34 -0700
Is There any support for the Webcam 3 (parallel port version under
linux?
------------------------------
From: Man <[EMAIL PROTECTED]>
Subject: Video Capture
Date: Tue, 10 Oct 2000 11:53:45 -0400
hello all,
I am looking for a video capture solution for linux (redhat). My
company is doing motion capture stuff and would like to use a linux
os.
What we need is a 15/30 frames per second capture card that can
capture raw (RGB) data and dump it onto the video texture memory. We
don't need it to dump onto disk. Any associated API's/SDK (C/C++)
would be required also.
If anyone can direct me to the right resources for accomplishing this,
you have my thanks in advance.
thanks all.
Man.
====== Posted via Newsfeeds.Com, Uncensored Usenet News ======
http://www.newsfeeds.com - The #1 Newsgroup Service in the World!
======= Over 80,000 Newsgroups = 16 Different Servers! ======
------------------------------
Date: Tue, 10 Oct 2000 18:16:37 +0200
From: Bartek Kostrzewa <[EMAIL PROTECTED]>
Crossposted-To: comp.os.linux.setup,linux.redhat.install
Subject: Re: Kernel Panic
Bryan Lee wrote:
>
> I managed to install RedHat Linux 6.2 on my PC which run on AMD Athlon
> 600MHZ with 128MB RAM.
>
> I never managed to go into Linux. The PC hang during the boot up (after the
> LILO prompt) and gave the following error messages:
>
> ==========
> ....... (some checking on system configuration)
> CPU: AMD AMD Athlon (tm) processor stepping 00
> Enabling extended fast FPU and restore ... done
> Disabling CPUID serial number ... general protection fault: 000
> :
> : < some error data>
> :
> Kernel panic: Attempted to kill the idel task!
> In swapper taksk - not syncing
>
> ==========
> That's the end of the screen output and the system hang there.
>
> Anybody can point me to the right direction to resolve this problem? Does
> Linux run on AMD processor?
Yes, that's a problem. The default RH 6.2 kernel has "Disable CPUID"
compiled in, and AMD's T-Birds panic when they see that. So, you need a
different kernel to boot (a boot disk, loadlin), and then recompile your
main kernel without said option.
--
Best regards,
Bartek Kostrzewa - [EMAIL PROTECTED]
<<< http://technoage.web.lu >>>
------------------------------
From: Remi Ricard <[EMAIL PROTECTED]>
Subject: Re: RedHat6.2 (or other) on Asus A7V Athlon system
Date: Tue, 10 Oct 2000 16:23:55 GMT
Hi,
Try to boot or install from the floppy to desactivated the serial number
probing.
Remi
Je77 wrote:
> Hello,
>
> I just assembled a quite nice machine and am having problems getting linux
> on it. I'm hoping someone has come across a similar problem and might be
> able to help. This is my system:
>
> Asus A7V Motherboard with an AMD Athlon 800 processor (Bios 1.0.3)
> Tekram DC-315U SCSI Controller
> SCSI CD-ROM (pretty generic; I forgot the name)
> Generic floppy
> IBM UDMA100 15Gb Hard Drive
> Matrox Millenium G400 Graphics Card
> Soundblaster 16 Audio Card
>
> I've tried to get RedHat6.2 working (both by SCSI CD-ROM and BOOT
> floppy). Unfortunately, it keeps on responding with "BOOT FAILED: PLEASE
> INSERT SYSTEM DRIVE" (or something very similar). Yuk! I have a version of
> slackware too which doesn't seem to work either.
>
> I've installed Linux on several systems (including Alpha and PPC), but
> I've never had difficulties this early in the process. Very frustrating.
>
> Peace and Luck!
>
> Je77
>
> --
> "They bought and sold it all; it's gone. They've taken it and built O-
> a mall. And, now, they're playing your song." --Hole (Celebrity Skin) 7
------------------------------
From: Remi Ricard <[EMAIL PROTECTED]>
Subject: Zip scsi card
Date: Tue, 10 Oct 2000 16:32:01 GMT
Hi,
My zip SCSI drive came with a "scsi card" do you know if this card is
well supported
in linux ? (really small card and I do not know the brand I was in the
same box as the
internal scsi zip drive)
Can a attach another scsi drive to this card (CD-RW) ?
I'm asking that because right now I have a ASUS P2B-S (with an
integrated scsi card on board)
and I'm using this scsi card but I buying a new computer and I don't
know if I need to
buy a SCSI card.
Remi
[EMAIL PROTECTED]
------------------------------
From: Henrik Carlqvist <[EMAIL PROTECTED]>
Subject: Re: SB128PCI won't play under SuSE Linux 6.4 - why?
Date: Mon, 09 Oct 2000 20:14:56 +0200
Jens Wendler wrote:
> Then the blue background of alsaconf vanishes, and you can read:
>
> "Starting sound driver: snd-card-ens1371
> alsactl: cannot open configuration file '/etc/asound.conf'"
> etc.
I suppose that you were running alsaconf as root? If so, what are the
permissions of /etc/asound.conf? Is /etc mounted readonly? I
/etc/asound.conf a directory when it is supposed to be a file?
> When I enter "modprobe snd-card-ens1371", insmod answers
> approximately this
> way: "snd-card-ens1371: Device or resource busy".
What does lsmod say?
regards Henrik
--
spammer strikeback:
root@localhost
[EMAIL PROTECTED]
------------------------------
From: [EMAIL PROTECTED] (Brad Friedman)
Subject: newbie: linux box hunt
Date: Tue, 10 Oct 2000 17:24:21 GMT
Does anyone know of a good Linux box vendor? I'm looking to get a descent
box (don't need a monitor) and am willing to spend up to $700.
Thanks,
BF
--
===============================================================================
------------------------------
From: [EMAIL PROTECTED] (Je77)
Subject: Re: RedHat6.2 (or other) on Asus A7V Athlon system
Date: 10 Oct 2000 17:20:09 GMT
In article <[EMAIL PROTECTED]>, Remi Ricard <[EMAIL PROTECTED]> wrote:
>Try to boot or install from the floppy to desactivated the serial number
>probing.
Thanks. I already tried this. My current theory is that it is the UDMA100
which is problematic. I'm waiting for RH7.0 to arrive before I try again.
Thanks for all the help,
Je77
--
"They bought and sold it all; it's gone. They've taken it and built O-
a mall. And, now, they're playing your song." --Hole (Celebrity Skin) 7
------------------------------
From: Matt Fuerst <[EMAIL PROTECTED]>
Subject: Re: Linux on Compaq Deskpro 6000 MP System
Date: Tue, 10 Oct 2000 13:28:50 -0400
It is dorky to reply to myself but I want to address points from all of you
so here I go:
First and foremost thanks for responding to my request!
As it turns out I am 99.99999% sure that the machine is in fact a DESKPRO
and not a Prolient. You can see my winning auction for the machine here -
http://cgi.ebay.com/aw-cgi/eBayISAPI.dll?ViewItem&item=448245827 - and I
think it is pretty clear the unit is definetly a workstation and not a
server of any sorts.
I am still looking forward to putting Linux on it. I was aware that Compaq
usually dumps the BIOS into a partition on the hard drive (cheap bastards)
instead of having a "real" BIOS so I will keep my eye out for that.
I am planning on upgrading the RAM.. does anyone have any experience with
SIMMS in Pentium Pro machine? I imagine they will have to be like 60ns?
Anyone have any experience with performance with a PPro in a dual setup as
compared to a single CPU? Anyone have any data on how it will run with say a
Dual PPro 200 / 1 MG Cache as compared to the 256K cache chips?
Thanks so much everyone!
Matt
Matt Fuerst wrote:
> Greetings,
>
> I just won an auction for a machine that is described as a Compaq 6000.
> It has a Pentium Pro 200 MHz chip installed, along with various other
> goodies (SCSI, Desktop Case, 32 MB of RAM, 2.5 GB HDD). I haven't been
> able to find much good information on this unit thus far but wil llikely
> have more infor once it gets to me anyways.
>
> Has anyone tried setting up Linux on such a machine? I understand that
> there is a second processor slot on the motherboard and I am definetly
> going to install a second processor as soon as I get my hands on the
> machine. I understand that the Penitum Pro line requires the same speed
> chip along with the same set of stepping information. Simple enough,
> there seems to be tons of PPro chips on ebay for relatively cheap
> prices. However, I also thought that the Pentium Pro Socket 8 had some
> funky requirements, something like a mounting bracket and exhaust
> system? Is that just my fuzzy memory? Basically, what else, other than
> the CPU, will I need to install a second processor into this machine?
> Any experiences? Any recommendations on where to get such things?
> (Obviously spending $100 on cooling the machine might be silly with the
> processors going for $30 each now-a-days).
>
> Does anyone have any experience with the various incarnations of cache
> sizes and how they relate to Linux? My current rig has a sole 200 MHz
> 256K chip but the units are cheap enough that I could get dual 200 MHz 1
> Meg chips... worth it? I am likely going to be installing Mandrake on
> the machine, using it for general dekstop purposes during the day, and
> log out of X and have it runnig as a Counter-Strike server durikng the
> nights (it's a game, like Quake). I am sure the answers might be
> different depending on the usage, so I figured I would mention that.
>
> Any other experiences? Are you happy? I would love to hear form people
> with this machine specifically.. I have tons of questions (SCSI is built
> in, my unit doesn't have a CD-ROM which is not a big deal at all since
> none of my linux machines have ever had a CD-ROM since network installs
> rock, but.. I have a closetfull of older SCSI CD-ROMs waiting for a
> home.. could I install in the unit?)
>
> Thanks so much for any and all input!
>
> Matt Fuerst
------------------------------
From: Moscito <[EMAIL PROTECTED]>
Subject: UDMA controller trouble with Micronics M6Me board
Date: 10 Oct 2000 19:12:40 GMT
Hello,
ladies and gentlemen, I have a problem. I have a Micronics
M6Me board (built-in SCSI, dual PPro, 440FX) board, which was fine
until I wanted to insert a UDMA disk as part of the RAID. It turned
out that the on-board IDE controller is connected via the ISA bus,
presumably just for CD-ROMs and such. I purchased a Promise UDMA/66
controller (PCI) trying to alleviate this problem, and managed to
re-install Red Hat 6.2 on a RAIDed partition after I manually input
the I/O port ranges for ide2 and ide3, so that the RAID consists of
partitions from hde as well as the SCSI drives. The problem is, I
still cannot seem to enable DMA. hdparm -D 1 ends with a cryptic
message telling that DMA cannot be enabled! Now the 7200 rpm EIDE
UDMA/66 drive sustain data at 4MB/s instead of 1MB/s, but it should
be able to do a lot more ...
Can someone inform me if this can be solved?
------------------------------
From: "bluster" <[EMAIL PROTECTED]>
Subject: Re: wrong hard drive info
Date: Tue, 10 Oct 2000 15:40:25 -0400
<[EMAIL PROTECTED]> wrote
> I had Linux running on a 5 gig WD drive and decided to move it onto an
> IBM 14 gig drive. I used the Ghost program to move the entire partition
> from one drive to another. It seems that linux has not realized that it
> is on a much bigger partition. df reports total 1k blocks as 4,862,400
> which is exactly the size of the old 5 gig drive. Is this a result of
> Ghost? If so, is there a way to fix it without loosing everything? If
> not, what is the best way to move a Linux partition from one drive to
> another?
I've never tried "ghost", I use the "cp -a" command, works every time.
This should help:
http://www.redhat.com/mirrors/LDP/HOWTO/mini/Hard-Disk-Upgrade/index.html
Bluster
------------------------------
From: "Ivan Danicic" <[EMAIL PROTECTED]>
Subject: Re: stcolor epson860
Date: Tue, 10 Oct 2000 19:59:10 +0100
Ivan Danicic <[EMAIL PROTECTED]> wrote in message news:...
> Hello, My printer has very poor resolution output when printing under
linux
> using the stcolor driver for ghostscript. The filter is:
>
> #!/bin/sh
> RESOLUTION=360x360
>
usr/bin/gs -q -dSAFER -dNOPAUSE -sDEVICE=stcolor -r$RESOLUTION -sOutputFil
> e=- -
>
> #end of filter
>
>
> Whatever I put into resolution (including nothing or 720x720) makes no
> difference.
> The resolution is excellent when printing under windows98. Any comments
> will be gratefully received.
> Ivan
> in London, UK.
>
> _________________________
> | Eppur' si muove - - Gallileo |
> *************************************
>
>
>
>
------------------------------
From: Roger Ehrlich <[EMAIL PROTECTED]>
Subject: IDE support on Sound card for CDROM?
Date: Tue, 10 Oct 2000 16:18:27 -0400
Hi
I wish to install Linux on an older 486 w/ IDE system BIOS (no EIDE, LBA, 2
channel support). I have a Creative Labs Sound Blaster 16 sound card with a
IDE (not proprietary) interface header on it. My HD controller has one IDE
channel w/ 2 HD's connected already to it. Will this "2nd" IDE via the snd
card be compatible with Linux?, I'd like to connect a CDROM drive to it.
I looked into the hardware Howto and Linux Hardware refs but found nothing.
My
own book of RedHat Linux 6.1 Configuration mentions that Creative had these
IDE interfaces on some of their cards that one could connect a CDROM drive
to
but does not state which driver is needed or if even this type of interface
will work. I remeber that in earlier versions of Linux this was not
supported.
Am I able to make this work now?
Thanks for any help.
Roger
[EMAIL PROTECTED]
============================================================
Get your FREE web-based e-mail and newsgroup access at:
http://MailAndNews.com
Create a new mailbox, or access your existing IMAP4 or
POP3 mailbox from anywhere with just a web browser.
============================================================
------------------------------
From: [EMAIL PROTECTED]
Subject: Wheel Mouse
Date: Tue, 10 Oct 2000 20:05:35 GMT
Is there any way to get my MicroSloth roller wheel on my mouse to work
with Red Hat 6.2? Or any PS2 wheel mouse for that matter?
Sent via Deja.com http://www.deja.com/
Before you buy.
------------------------------
Crossposted-To: comp.sys.sun.hardware
Subject: Re: Sparc/Solaris vs Intel/Linux: Webserver
From: Andrew Donkin <[EMAIL PROTECTED]>
Date: 11 Oct 2000 09:39:16 +1300
Chris Harshman <[EMAIL PROTECTED]> writes:
[EMAIL PROTECTED] wrote:
>> I'm looking at the following systems to use as webserver:
>> 1. Compaq DL360 pIII 550 w/ 256 MB running Linux/Apache
> Our experience with the DL360 as a Linux platform (with
> Compaq-installed RH6.2) was not favourable. We could not get the
> ethernet interface to initialize when running an SMP kernel (2x 833MHz
> PIII), though we used the latest drivers (e100 v1.1.x). When we
> brought the system up using the non-SMP kernel (the box shipped with
> both installed) the ethernet initialized fine.
The DL360 has a different ethernet card from the DL380? Are they using
an I815e chipset?
We're using DL380s here with no problems. It's nice to have hardware
RAID. Even the standard kernel ethernet driver works well:
eepro100.c:v1.09j-t 9/29/99 Donald Becker
http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html
eepro100.c: $Revision: 1.20.2.10 $ 2000/05/31 Modified by Andrey V. Savochkin
<[EMAIL PROTECTED]> and others
eth0: OEM i82557/i82558 10/100 Ethernet, 00:50:8B:DE:92:EA, I/O at 0x2400, IRQ 10.
Receiver lock-up bug exists -- enabling work-around.
Board assembly 010101-034, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
eepro100.c:v1.09j-t 9/29/99 Donald Becker
http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html
eepro100.c: $Revision: 1.20.2.10 $ 2000/05/31 Modified by Andrey V. Savochkin
<[EMAIL PROTECTED]> and others
(though I have no idea why we get that banner twice)
--
_________________________________________________________________________
Andrew Donkin Waikato University, Hamilton, New Zealand
------------------------------
From: [EMAIL PROTECTED]
Crossposted-To: comp.os.linux.misc
Subject: Re: SCSI tape drive problem w/ RH 6.1
Date: Tue, 10 Oct 2000 20:31:13 GMT
> On Wed, 20 Sep 2000 13:58:16 GMT, Harshal <[EMAIL PROTECTED]> wrote:
> >Thanks for all your help.
> >I can now use the tape drive if I manually load the aic7xxx and st modules.
> >But even though I have the 'alias scsi_hostadapter aic7xxx' line in
> >/etc/conf.modules, the module is not automatically loaded on re-boot.
> >Do I have to use '/sbin/mkinitrd' to generate a new ramdisk image?
> >- Harshal.
>
> Yes.
> --
> Dick Freedman
>
Harshal: I have followed this entire thread of about fixing Linux 6.1 so it
would recognize your tape drive. There appear to be 4 pieces to the puzzle
but only three solutions were printed in the messages. Those four pieces
were:
Problem Solution 1) host adaptor
alias scsi_hostadapter aic7xxx in /etc/conf.modules 2) scsi tape support
/sbin/insmod/st in /etc/conf.modules 3) scsi core module
? 4) new ramdisk image /sbin/mkinitrd in /etc/conf.modules
How did you get SCSI core support? Did you use the command
/sbin/insmod/scsi_mod ? Did you put the command into /etc/conf.modules?
It appears from the thread that you did NOT have to recompile the kernel,
correct?
Sent via Deja.com http://www.deja.com/
Before you buy.
------------------------------
From: [EMAIL PROTECTED] (Mile Davidovic)
Subject: Re: Adding a Windows hard drive
Date: 10 Oct 2000 20:36:15 GMT
Reply-To: [EMAIL PROTECTED]
Nop, some rare cable have only 2 connector.
>Every single IDE cable set I've ever seen simply
>had three connectors on an unmodified ribbon cable; all three connector
>identically connected.
--
------------------------------
From: Jim McDonald <[EMAIL PROTECTED]>
Crossposted-To: comp.os.linux.setup,linux.redhat.install
Subject: Re: Kernel Panic
Date: Tue, 10 Oct 2000 13:48:34 -0700
Bartek Kostrzewa wrote:
>
> Bryan Lee wrote:
> >
> > Anybody can point me to the right direction to resolve this problem? Does
> > Linux run on AMD processor?
>
> Yes, that's a problem. The default RH 6.2 kernel has "Disable CPUID"
> compiled in, and AMD's T-Birds panic when they see that. So, you need a
> different kernel to boot (a boot disk, loadlin), and then recompile your
> main kernel without said option.
>
Or type "linux x86_serial_nr=1" at the lilo prompt; you should be able
to append it in lilo.conf, too.
--
Jim McDonald
htttp://www.stanford.edu/~mcduck
------------------------------
From: Mike <[EMAIL PROTECTED]>
Crossposted-To: comp.os.linux.misc
Subject: Re: SCSI tape drive problem w/ RH 6.1
Date: Tue, 10 Oct 2000 20:54:04 GMT
Oops. Let me try that again without the tab key so it's legible:
There appeared to be 4 pieces to the puzzle but only three of the
solutions were printed in the messages. Those four pieces were:
1) host adaptor solution=alias scsi_hostadapter aic7xxx in
/etc/conf.modules
2) scsi tape support solution= /sbin/insmod/st in /etc/conf.modules
3) scsi core module solution= ?
4) new ramdisk image solution= /sbin/mkinitrd in /etc/conf.modules
How did you get SCSI core support? Did you use the command
/sbin/insmod/scsi_mod ? Did you put the command into /etc/conf.modules?
It appears from the thread that you did NOT have to recompile the
kernel, correct?
Sent via Deja.com http://www.deja.com/
Before you buy.
------------------------------
** FOR YOUR REFERENCE **
The service address, to which questions about the list itself and requests
to be added to or deleted from it should be directed, is:
Internet: [EMAIL PROTECTED]
You can send mail to the entire list (and comp.os.linux.hardware) via:
Internet: [EMAIL PROTECTED]
Linux may be obtained via one of these FTP sites:
ftp.funet.fi pub/Linux
tsx-11.mit.edu pub/linux
sunsite.unc.edu pub/Linux
End of Linux-Hardware Digest
******************************
