Add basic panel support for the Nokia N950. It must be tweaked a
little bit later, since the panel was built into the device
upside-down. Also the first 5 and the last 5 pixels are covered
by plastic.
Signed-off-By: Sebastian Reichel <sebastian.reic...@collabora.co.uk>
---
arch/arm/boot/dts/omap3-n950.dts | 88 ++++++++++++++++++++++++++++++++++++++++
1 file changed, 88 insertions(+)
diff --git a/arch/arm/boot/dts/omap3-n950.dts b/arch/arm/boot/dts/omap3-n950.dts
index 646601a3ebd8..ef70aae99d1b 100644
--- a/arch/arm/boot/dts/omap3-n950.dts
+++ b/arch/arm/boot/dts/omap3-n950.dts
@@ -51,6 +51,26 @@
};
};
+&omap3_pmx_core {
+ dsi_pins: pinmux_dsi_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE1) /*
dsi_dx0 - data0+ */
+ OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE1) /*
dsi_dy0 - data0- */
+ OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE1) /*
dsi_dx1 - clk+ */
+ OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE1) /*
dsi_dy1 - clk- */
+ OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE1) /*
dsi_dx2 - data1+ */
+ OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE1) /*
dsi_dy2 - data1- */
+ >;
+ };
+
+ display_pins: pinmux_display_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x20ca, PIN_INPUT | MUX_MODE4) /*
gpio 62 - display te */
+ OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE4) /*
gpio 87 - display reset */
+ >;
+ };
+};
+
&i2c2 {
smia_1: camera@10 {
compatible = "nokia,smia";
@@ -185,3 +205,71 @@
st,max-limit-y = <32>;
st,max-limit-z = <32>;
};
+
+&dss {
+ status = "ok";
+
+ vdda_video-supply = <&vdac>;
+};
+
+&dsi {
+ status = "ok";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dsi_pins>;
+
+ vdd-supply = <&vpll2>;
+
+ port {
+ dsi_out_ep: endpoint {
+ remote-endpoint = <&lcd0_in>;
+ lanes = <2 3 0 1 4 5>;
+ };
+ };
+
+ lcd0: display {
+ compatible = "nokia,himalaya", "panel-dsi-cm";
+ label = "lcd0";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&display_pins>;
+
+ vpnl-supply = <&vmmc2>;
+ vddi-supply = <&vio>;
+
+ reset-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>; /* 87 */
+ te-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>; /* 62 */
+
+ width-mm = <49>; /* 48.960 mm */
+ height-mm = <88>; /* 88.128 mm */
+
+ /* TODO:
+ * - panel is upside-down
+ * - top + bottom 5px are not visible
+ */
+ panel-timing {
+ clock-frequency = <0>; /* Calculated by dsi */
+
+ hback-porch = <2>;
+ hactive = <480>;
+ hfront-porch = <0>;
+ hsync-len = <2>;
+
+ vback-porch = <1>;
+ vactive = <864>;
+ vfront-porch = <0>;
+ vsync-len = <1>;
+
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ port {
+ lcd0_in: endpoint {
+ remote-endpoint = <&dsi_out_ep>;
+ };
+ };
+ };
+};
--
2.13.2
