On 05/22/2018 01:07 PM, Philipp Zabel wrote:
> Hi Marek,
>
> On Fri, 2018-05-18 at 18:21 +0200, Marek Vasut wrote:
>> On 05/18/2018 05:51 PM, Philipp Zabel wrote:
>>> Hi Marek,
>>>
>>> On Sat, 2018-04-07 at 15:04 +0200, Marek Vasut wrote:
>>>> The BT1120 interlaced CCIR codes are the same as BT656 ones
>>>> and different than BT656 progressive CCIR codes, fix this.
>>>
>>> thank you for the patch, and sorry for the delay.
>>>
>>>> Signed-off-by: Marek Vasut <[email protected]>
>>>> Cc: Steve Longerbeam <[email protected]>
>>>> Cc: Philipp Zabel <[email protected]>
>>>> ---
>>>> drivers/gpu/ipu-v3/ipu-csi.c | 8 ++++++--
>>>> 1 file changed, 6 insertions(+), 2 deletions(-)
>>>>
>>>> diff --git a/drivers/gpu/ipu-v3/ipu-csi.c b/drivers/gpu/ipu-v3/ipu-csi.c
>>>> index caa05b0702e1..301a729581ce 100644
>>>> --- a/drivers/gpu/ipu-v3/ipu-csi.c
>>>> +++ b/drivers/gpu/ipu-v3/ipu-csi.c
>>>> @@ -435,12 +435,16 @@ int ipu_csi_init_interface(struct ipu_csi *csi,
>>>> break;
>>>> case IPU_CSI_CLK_MODE_CCIR1120_PROGRESSIVE_DDR:
>>>> case IPU_CSI_CLK_MODE_CCIR1120_PROGRESSIVE_SDR:
>>>> - case IPU_CSI_CLK_MODE_CCIR1120_INTERLACED_DDR:
>>>> - case IPU_CSI_CLK_MODE_CCIR1120_INTERLACED_SDR:
>>>> ipu_csi_write(csi, 0x40030 | CSI_CCIR_ERR_DET_EN,
>>>> CSI_CCIR_CODE_1);
>>>> ipu_csi_write(csi, 0xFF0000, CSI_CCIR_CODE_3);
>>>> break;
>>>> + case IPU_CSI_CLK_MODE_CCIR1120_INTERLACED_DDR:
>>>> + case IPU_CSI_CLK_MODE_CCIR1120_INTERLACED_SDR:
>>>> + ipu_csi_write(csi, 0x40596 | CSI_CCIR_ERR_DET_EN,
>>>> CSI_CCIR_CODE_1);
>>>> + ipu_csi_write(csi, 0xD07DF, CSI_CCIR_CODE_2);
>>>> + ipu_csi_write(csi, 0xFF0000, CSI_CCIR_CODE_3);
>>>
>>> If these are the same as BT656 codes (so this case would be for PAL?),
>>> could this just be moved up into the IPU_CSI_CLK_MODE_CCIR656_INTERLACED
>>> case? Would the NTSC CCIR codes be the same as well?
>>
>> Dunno, I don't have any NTSC device to test. But the above was tested
>> with a PAL device I had.
>>
>> I think the CCIR codes are different from BT656, although I might be wrong.
>
> The driver currently has:
>
> case IPU_CSI_CLK_MODE_CCIR656_INTERLACED:
> if (mbus_fmt->width == 720 && mbus_fmt->height == 576) {
> /*
> * PAL case
> *
> * Field0BlankEnd = 0x6, Field0BlankStart = 0x2,
> * Field0ActiveEnd = 0x4, Field0ActiveStart = 0
> * Field1BlankEnd = 0x7, Field1BlankStart = 0x3,
> * Field1ActiveEnd = 0x5, Field1ActiveStart = 0x1
> */
> height = 625; /* framelines for PAL */
>
> ipu_csi_write(csi, 0x40596 | CSI_CCIR_ERR_DET_EN,
> CSI_CCIR_CODE_1);
> ipu_csi_write(csi, 0xD07DF, CSI_CCIR_CODE_2);
> ipu_csi_write(csi, 0xFF0000, CSI_CCIR_CODE_3);
> } else if (mbus_fmt->width == 720 && mbus_fmt->height == 480)
> {
> /*
> * NTSC case
> *
> * Field0BlankEnd = 0x7, Field0BlankStart = 0x3,
> * Field0ActiveEnd = 0x5, Field0ActiveStart = 0x1
> * Field1BlankEnd = 0x6, Field1BlankStart = 0x2,
> * Field1ActiveEnd = 0x4, Field1ActiveStart = 0
> */
> height = 525; /* framelines for NTSC */
>
> ipu_csi_write(csi, 0xD07DF | CSI_CCIR_ERR_DET_EN,
> CSI_CCIR_CODE_1);
> ipu_csi_write(csi, 0x40596, CSI_CCIR_CODE_2);
> ipu_csi_write(csi, 0xFF0000, CSI_CCIR_CODE_3);
> } else {
> dev_err(csi->ipu->dev,
> "Unsupported CCIR656 interlaced video
> mode\n");
> spin_unlock_irqrestore(&csi->lock, flags);
> return -EINVAL;
> }
> break;
>
> The PAL codes are exactly the same as in your patch. That's why I wonder
> whether we should just move
> case IPU_CSI_CLK_MODE_CCIR1120_INTERLACED_DDR:
> case IPU_CSI_CLK_MODE_CCIR1120_INTERLACED_SDR:
> up before
> case IPU_CSI_CLK_MODE_CCIR656_INTERLACED:
> as follows:
Isn't the PAL code doing some sort of resolution check too ? Although
this would probably work in my case too.
> ----------8<----------
> diff --git a/drivers/gpu/ipu-v3/ipu-csi.c b/drivers/gpu/ipu-v3/ipu-csi.c
> index caa05b0702e1..7e96382f9cb1 100644
> --- a/drivers/gpu/ipu-v3/ipu-csi.c
> +++ b/drivers/gpu/ipu-v3/ipu-csi.c
> @@ -396,6 +396,8 @@ int ipu_csi_init_interface(struct ipu_csi *csi,
> ipu_csi_write(csi, 0xFF0000, CSI_CCIR_CODE_3);
> break;
> case IPU_CSI_CLK_MODE_CCIR656_INTERLACED:
> + case IPU_CSI_CLK_MODE_CCIR1120_INTERLACED_DDR:
> + case IPU_CSI_CLK_MODE_CCIR1120_INTERLACED_SDR:
> if (mbus_fmt->width == 720 && mbus_fmt->height == 576) {
> /*
> * PAL case
> @@ -435,8 +437,6 @@ int ipu_csi_init_interface(struct ipu_csi *csi,
> break;
> case IPU_CSI_CLK_MODE_CCIR1120_PROGRESSIVE_DDR:
> case IPU_CSI_CLK_MODE_CCIR1120_PROGRESSIVE_SDR:
> - case IPU_CSI_CLK_MODE_CCIR1120_INTERLACED_DDR:
> - case IPU_CSI_CLK_MODE_CCIR1120_INTERLACED_SDR:
> ipu_csi_write(csi, 0x40030 | CSI_CCIR_ERR_DET_EN,
> CSI_CCIR_CODE_1);
> ipu_csi_write(csi, 0xFF0000, CSI_CCIR_CODE_3);
> ---------->8----------
>
> Does this work for you?
I cannot test this anymore, but maybe it'll help someone.
--
Best regards,
Marek Vasut
