Hi Thara,
On Fri, Mar 5, 2010 at 5:22 PM, Gopinath, Thara <[email protected]> wrote:
> Will do this as V2
Can you please remove the chunks of text you are not replying to in your mails?
All the following text is just a waste of bandwidth, and time for
people that actually scroll down trying to find further comments. This
is a practice not only you, but other people have started to follow in
this mailing list and it's annoying me a bit.
Cheers.
>>>
>>>> ---
>>>> arch/arm/mach-omap2/voltage.c | 149
>>>> +++++++++++++++++++++++++++++++++++++++--
>>>> arch/arm/mach-omap2/voltage.h | 1 +
>>>> arch/arm/plat-omap/Kconfig | 19 +++++
>>>> 3 files changed, 162 insertions(+), 7 deletions(-)
>>>>
>>>> diff --git a/arch/arm/mach-omap2/voltage.c b/arch/arm/mach-omap2/voltage.c
>>>> index 49167c0..4f325af 100644
>>>> --- a/arch/arm/mach-omap2/voltage.c
>>>> +++ b/arch/arm/mach-omap2/voltage.c
>>>> @@ -29,7 +29,8 @@
>>>> #include "prm-regbits-34xx.h"
>>>> #include "voltage.h"
>>>>
>>>> -#define VP_IDLE_TIMEOUT 200
>>>> +#define VP_IDLE_TIMEOUT 200
>>>> +#define VP_TRANXDONE_TIMEOUT 300
>>>>
>>>> /*
>>>> * OMAP3 Voltage controller SR parameters. TODO: Pass this info as part of
>>>> @@ -70,6 +71,7 @@ struct vp_reg_info {
>>>> u32 vp_vddmin;
>>>> u32 vp_vddmax;
>>>> u32 vp_timeout;
>>>> + u32 vp_tranxdone_status;
>>>> };
>>>> static struct vp_reg_info *vp_reg;
>>>> /*
>>>> @@ -299,6 +301,8 @@ static void __init vp_reg_configure(int vp_id)
>>>> OMAP3430_VDDMIN_SHIFT);
>>>> vp_reg[vp_id].vp_vddmax = (OMAP3_VP1_VLIMITTO_VDDMAX <<
>>>> OMAP3430_VDDMAX_SHIFT);
>>>> + vp_reg[vp_id].vp_tranxdone_status =
>>>> + OMAP3430_VP1_TRANXDONE_ST;
>>>> } else if (vp_id == VP2) {
>>>> /*
>>>> * OMAP3430 has error gain varying btw higher and
>>>> @@ -312,6 +316,8 @@ static void __init vp_reg_configure(int vp_id)
>>>> OMAP3430_VDDMIN_SHIFT);
>>>> vp_reg[vp_id].vp_vddmax = (OMAP3_VP2_VLIMITTO_VDDMAX <<
>>>> OMAP3430_VDDMAX_SHIFT);
>>>> + vp_reg[vp_id].vp_tranxdone_status =
>>>> + OMAP3430_VP2_TRANXDONE_ST;
>>>> } else {
>>>> pr_warning("Voltage processor%d does not exisit\
>>>> in OMAP3 \n", vp_id);
>>>> @@ -346,6 +352,131 @@ static void __init vp_reg_configure(int vp_id)
>>>> /* TODO Extend this for OMAP4 ?? Or need a separate file */
>>>> }
>>>>
>>>> +#ifdef CONFIG_OMAP_VOLT_VPFORCEUPDATE
>>>> +/* VP force update method of voltage scaling */
>>>> +static int vp_forceupdate_scale_voltage(u32 vdd, u8 target_vsel,
>>>> + u8 current_vsel)
>>>> +{
>>>> + u32 smps_steps = 0, smps_delay = 0;
>>>> + u32 vpconfig;
>>>> + int timeout = 0;
>>>> + int vp_id = vdd - 1;
>>>> +
>>>> + if (!((vdd == VDD1_OPP) || (vdd == VDD2_OPP))) {
>>>> + pr_warning("Wrong vdd id passed to vp forceupdate\n");
>>>> + return false;
>>>> + }
>>>> +
>>>> + smps_steps = abs(target_vsel - current_vsel);
>>>> +
>>>> + /* OMAP3430 has errorgain varying btw higher and lower opp's */
>>>> + if (cpu_is_omap34xx()) {
>>>> + if (vdd == VDD1_OPP) {
>>>> + u32 vc_cmdval0;
>>>> +
>>>> + vc_cmdval0 = voltage_read_reg(vc_reg.vc_cmdval0_reg);
>>>> + vc_cmdval0 &= ~VC_CMD_ON_MASK;
>>>> + vc_cmdval0 |= (target_vsel << VC_CMD_ON_SHIFT);
>>>> + voltage_write_reg(vc_reg.vc_cmdval0_reg, vc_cmdval0);
>>>> + vp_reg[vp_id].vp_errorgain = (((get_vdd1_opp() > 2) ?
>>>> + (OMAP3_VP_CONFIG_ERRORGAIN_HIGHOPP) :
>>>> + (OMAP3_VP_CONFIG_ERRORGAIN_LOWOPP)) <<
>>>> + OMAP3430_ERRORGAIN_SHIFT);
>>>> + } else if (vdd == VDD2_OPP) {
>>>> + u32 vc_cmdval1;
>>>> +
>>>> + vc_cmdval1 = voltage_read_reg(vc_reg.vc_cmdval1_reg);
>>>> + vc_cmdval1 &= ~VC_CMD_ON_MASK;
>>>> + vc_cmdval1 |= (target_vsel << VC_CMD_ON_SHIFT);
>>>> + voltage_write_reg(vc_reg.vc_cmdval1_reg, vc_cmdval1);
>>>> + vp_reg[vp_id].vp_errorgain = (((get_vdd2_opp() > 2) ?
>>>> + (OMAP3_VP_CONFIG_ERRORGAIN_HIGHOPP) :
>>>> + (OMAP3_VP_CONFIG_ERRORGAIN_LOWOPP)) <<
>>>> + OMAP3430_ERRORGAIN_SHIFT);
>>>> + }
>>>> + }
>>>> +
>>>> + /* Clear all pending TransactionDone interrupt/status. Typical latency
>>>> + * is <3us
>>>> + */
>>>> + while (timeout++ < VP_TRANXDONE_TIMEOUT) {
>>>> + voltage_write_reg(PRM_IRQSTATUS_REG,
>>>> + vp_reg[vp_id].vp_tranxdone_status);
>>>> + if (!(voltage_read_reg(PRM_IRQSTATUS_REG) &
>>>> + vp_reg[vp_id].vp_tranxdone_status))
>>>> + break;
>>>> + udelay(1);
>>>> + }
>>>> +
>>>> + if (timeout >= VP_TRANXDONE_TIMEOUT) {
>>>> + pr_warning("VP%d TRANXDONE timeout exceeded. Voltage change \
>>>> + aborted", vdd);
>>>> + return false;
>>>> + }
>>>> +
>>>> + /* Configure for VP-Force Update */
>>>> + vpconfig = voltage_read_reg(vp_reg[vp_id].vp_offs.vp_vpconfig_reg);
>>>> + vpconfig &= ~(VP_CONFIG_INITVDD | VP_FORCEUPDATE |
>>>> + VP_INITVOLTAGE_MASK | VP_ERRORGAIN_MASK);
>>>> + vpconfig |= ((target_vsel << VP_INITVOLTAGE_SHIFT) |
>>>> + vp_reg[vp_id].vp_errorgain);
>>>> + voltage_write_reg(vp_reg[vp_id].vp_offs.vp_vpconfig_reg, vpconfig);
>>>> +
>>>> + /* Trigger initVDD value copy to voltage processor */
>>>> + vpconfig |= VP_CONFIG_INITVDD;
>>>> + voltage_write_reg(vp_reg[vp_id].vp_offs.vp_vpconfig_reg, vpconfig);
>>>> +
>>>> + /* Force update of voltage */
>>>> + vpconfig |= VP_FORCEUPDATE;
>>>> + voltage_write_reg(vp_reg[vp_id].vp_offs.vp_vpconfig_reg, vpconfig);
>>>> +
>>>> + timeout = 0;
>>>> + /* Wait for TransactionDone. Typical latency is <200us.
>>>> + * Depends on SMPSWAITTIMEMIN/MAX and voltage change
>>>> + */
>>>
>>>multi-line comment style
>>>
>>>> + while ((timeout++ < VP_TRANXDONE_TIMEOUT) &&
>>>> + (!(voltage_read_reg(PRM_IRQSTATUS_REG) &
>>>> + vp_reg[vp_id].vp_tranxdone_status)))
>>>> + udelay(1);
>>>> +
>>>> + if (timeout >= VP_TRANXDONE_TIMEOUT)
>>>> + pr_warning("VP%d TRANXDONE timeout exceeded. TRANXDONE never \
>>>> + got set after the voltage update.Serious error!!!!\n",
>>>> + vdd);
>>>> +
>>>> + /* Wait for voltage to settle with SW wait-loop */
>>>> + smps_delay = ((smps_steps * 125) / 40) + 2;
>>>> + udelay(smps_delay);
>>>> +
>>>> + /* Disable TransactionDone interrupt , clear all status, clear
>>>> + * control registers
>>>> + */
>>>
>>>muti-line comment
>>>
>>>> + timeout = 0;
>>>> + while (timeout++ < VP_TRANXDONE_TIMEOUT) {
>>>> + voltage_write_reg(PRM_IRQSTATUS_REG,
>>>> + vp_reg[vp_id].vp_tranxdone_status);
>>>> + if (!(voltage_read_reg(PRM_IRQSTATUS_REG) &
>>>> + vp_reg[vp_id].vp_tranxdone_status))
>>>> + break;
>>>> + udelay(1);
>>>> + }
>>>> + if (timeout >= VP_TRANXDONE_TIMEOUT)
>>>> + pr_warning("VP%d TRANXDONE timeout exceeded while trying to \
>>>> + clear the TRANXDONE status\n", vdd);
>>>> +
>>>> + vpconfig = voltage_read_reg(vp_reg[vp_id].vp_offs.vp_vpconfig_reg);
>>>> + /* Clear initVDD copy trigger bit */
>>>> + vpconfig &= ~VP_CONFIG_INITVDD;
>>>> + voltage_write_reg(vp_reg[vp_id].vp_offs.vp_vpconfig_reg, vpconfig);
>>>> + /* Clear force bit */
>>>> + vpconfig &= ~VP_FORCEUPDATE;
>>>> + voltage_write_reg(vp_reg[vp_id].vp_offs.vp_vpconfig_reg, vpconfig);
>>>> +
>>>> + return true;
>>>> +}
>>>> +#endif
>>>> +
>>>> +#ifdef CONFIG_OMAP_VOLT_VCBYPASS
>>>> /**
>>>> * vc_bypass_scale_voltage - VC bypass method of voltage scaling
>>>> */
>>>> @@ -437,7 +568,7 @@ static int vc_bypass_scale_voltage(u32 vdd, u8
>>>> target_vsel, u8 current_vsel)
>>>> udelay(smps_delay);
>>>> return true;
>>>> }
>>>> -
>>>> +#endif
>>>>
>>>> static void __init init_voltageprocessors(void)
>>>> {
>>>> @@ -474,13 +605,16 @@ void omap_voltageprocessor_enable(int vp_id)
>>>> if (voltage_read_reg(vp_reg[vp_id - 1].vp_offs.vp_vpconfig_reg) &
>>>> VP_CONFIG_VPENABLE)
>>>> return;
>>>> +
>>>> +#ifdef CONFIG_OMAP_VOLT_VCBYPASS
>>>> /*
>>>> * This latching is required only if VC bypass method is used for
>>>> * voltage scaling during dvfs.
>>>> */
>>>> vp_latch_vsel(vp_id - 1);
>>>> - vpconfig = voltage_read_reg(vp_reg[vp_id - 1].vp_offs.vp_vpconfig_reg);
>>>> +#endif
>>>> /* Enable VP */
>>>> + vpconfig = voltage_read_reg(vp_reg[vp_id - 1].vp_offs.vp_vpconfig_reg);
>>>> voltage_write_reg(vp_reg[vp_id - 1].vp_offs.vp_vpconfig_reg,
>>>> vpconfig | VP_CONFIG_VPENABLE);
>>>> }
>>>> @@ -529,11 +663,12 @@ void omap_voltageprocessor_disable(int vp_id)
>>>> * for a particular voltage domain during dvfs or any other situation.
>>>> */
>>>> int omap_voltage_scale(int vdd, u8 target_vsel, u8 current_vsel)
>>>> -{ /*
>>>> - * TODO add VP force update method of voltage scaling
>>>> - * and choose btw the two
>>>> - */
>>>> +{
>>>> +#ifdef CONFIG_OMAP_VOLT_VCBYPASS
>>>> return vc_bypass_scale_voltage(vdd, target_vsel, current_vsel);
>>>> +#elif CONFIG_OMAP_VOLT_VPFORCEUPDATE
>>>> + return vp_forceupdate_scale_voltage(vdd, target_vsel, current_vsel);
>>>> +#endif
>>>> }
>>>>
>>>> /**
>>>> diff --git a/arch/arm/mach-omap2/voltage.h b/arch/arm/mach-omap2/voltage.h
>>>> index c3203c9..615bde6 100644
>>>> --- a/arch/arm/mach-omap2/voltage.h
>>>> +++ b/arch/arm/mach-omap2/voltage.h
>>>> @@ -17,6 +17,7 @@
>>>> extern int get_vdd1_opp(void);
>>>> extern int get_vdd2_opp(void);
>>>>
>>>> +#define PRM_IRQSTATUS_REG OMAP3430_PRM_IRQSTATUS_MPU
>>>> /* Generic VP definitions. Need to be redefined for OMAP4 */
>>>> #define VP_CONFIG_TIMEOUTEN OMAP3430_TIMEOUTEN
>>>> #define VP_CONFIG_INITVDD OMAP3430_INITVDD
>>>> diff --git a/arch/arm/plat-omap/Kconfig b/arch/arm/plat-omap/Kconfig
>>>> index 9d286e6..1a611a9 100644
>>>> --- a/arch/arm/plat-omap/Kconfig
>>>> +++ b/arch/arm/plat-omap/Kconfig
>>>> @@ -92,6 +92,25 @@ config OMAP_SMARTREFLEX_TESTING
>>>>
>>>> WARNING: Enabling this option may cause your device to hang!
>>>>
>>>> +choice
>>>> + prompt "Choose Voltage Scale method"
>>>> + depends on ARCH_OMAP3 && PM
>>>> + default OMAP_VOLT_VPFORCEUPDATE
>>>> +
>>>> +config OMAP_VOLT_VPFORCEUPDATE
>>>> + bool "Voltage scaling via VP force update method"
>>>> + help
>>>> + Say Y if you want to enable VP force update method
>>>> + of voltage scaling. This is the h/w recomended way
>>>> + of voltage scaling in OMAP3.
>>>> +
>>>> +config OMAP_VOLT_VCBYPASS
>>>> + bool "Voltage Scale via Voltage controller in bypass"
>>>> + help
>>>> + Say Y if you want to enable VC Bypass method of voltage scaling.
>>>> + Not the default recommended method.
>>>> +endchoice
>>>> +
>>>> config OMAP_RESET_CLOCKS
>>>> bool "Reset unused clocks during boot"
>>>> depends on ARCH_OMAP
>>>> --
>>>> 1.7.0.rc1.33.g07cf0f
> --
> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
> the body of a message to [email protected]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
Felipe Contreras
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
