> -----Original Message-----
> From: Felipe Balbi [mailto:[email protected]]
> Sent: Thursday, April 01, 2010 12:47 PM
> To: Varadarajan, Charulatha
> Cc: [email protected]; Nayak, Rajendra; [email protected];
> [email protected]
> Subject: Re: [PATCH 1/8] OMAP:GPIO:Move architecture specific macros to
> specific
> header
>
> Hi,
>
> On Wed, Mar 31, 2010 at 02:23:52PM +0200, ext Charulatha V wrote:
> >diff --git a/arch/arm/mach-omap1/include/mach/gpio.h b/arch/arm/mach-
> omap1/include/mach/gpio.h
> >index e737706..c4945d7 100644
> >--- a/arch/arm/mach-omap1/include/mach/gpio.h
> >+++ b/arch/arm/mach-omap1/include/mach/gpio.h
> >@@ -3,3 +3,91 @@
> > */
> >
> > #include <plat/gpio.h>
> >+
> >+/*
> >+ * OMAP1510 GPIO registers
> >+ */
> >+#define OMAP1510_GPIO_BASE 0xfffce000
> >+#define OMAP1510_GPIO_DATA_INPUT 0x00
> >+#define OMAP1510_GPIO_DATA_OUTPUT 0x04
> >+#define OMAP1510_GPIO_DIR_CONTROL 0x08
> >+#define OMAP1510_GPIO_INT_CONTROL 0x0c
> >+#define OMAP1510_GPIO_INT_MASK 0x10
> >+#define OMAP1510_GPIO_INT_STATUS 0x14
> >+#define OMAP1510_GPIO_PIN_CONTROL 0x18
> >+
> >+#define OMAP1510_IH_GPIO_BASE 64
> >+
> >+/*
> >+ * OMAP1610 specific GPIO registers
> >+ */
> >+#define OMAP1610_GPIO1_BASE 0xfffbe400
> >+#define OMAP1610_GPIO2_BASE 0xfffbec00
> >+#define OMAP1610_GPIO3_BASE 0xfffbb400
> >+#define OMAP1610_GPIO4_BASE 0xfffbbc00
> >+#define OMAP1610_GPIO_REVISION 0x0000
> >+#define OMAP1610_GPIO_SYSCONFIG 0x0010
> >+#define OMAP1610_GPIO_SYSSTATUS 0x0014
> >+#define OMAP1610_GPIO_IRQSTATUS1 0x0018
> >+#define OMAP1610_GPIO_IRQENABLE1 0x001c
> >+#define OMAP1610_GPIO_WAKEUPENABLE 0x0028
> >+#define OMAP1610_GPIO_DATAIN 0x002c
> >+#define OMAP1610_GPIO_DATAOUT 0x0030
> >+#define OMAP1610_GPIO_DIRECTION 0x0034
> >+#define OMAP1610_GPIO_EDGE_CTRL1 0x0038
> >+#define OMAP1610_GPIO_EDGE_CTRL2 0x003c
> >+#define OMAP1610_GPIO_CLEAR_IRQENABLE1 0x009c
> >+#define OMAP1610_GPIO_CLEAR_WAKEUPENA 0x00a8
> >+#define OMAP1610_GPIO_CLEAR_DATAOUT 0x00b0
> >+#define OMAP1610_GPIO_SET_IRQENABLE1 0x00dc
> >+#define OMAP1610_GPIO_SET_WAKEUPENA 0x00e8
> >+#define OMAP1610_GPIO_SET_DATAOUT 0x00f0
> >+
> >+/*
> >+ * OMAP7XX specific GPIO registers
> >+ */
> >+#define OMAP7XX_GPIO1_BASE 0xfffbc000
> >+#define OMAP7XX_GPIO2_BASE 0xfffbc800
> >+#define OMAP7XX_GPIO3_BASE 0xfffbd000
> >+#define OMAP7XX_GPIO4_BASE 0xfffbd800
> >+#define OMAP7XX_GPIO5_BASE 0xfffbe000
> >+#define OMAP7XX_GPIO6_BASE 0xfffbe800
> >+#define OMAP7XX_GPIO_DATA_INPUT 0x00
> >+#define OMAP7XX_GPIO_DATA_OUTPUT 0x04
> >+#define OMAP7XX_GPIO_DIR_CONTROL 0x08
> >+#define OMAP7XX_GPIO_INT_CONTROL 0x0c
> >+#define OMAP7XX_GPIO_INT_MASK 0x10
> >+#define OMAP7XX_GPIO_INT_STATUS 0x14
> >+
> >+#define OMAP1_MPUIO_VBASE OMAP1_MPUIO_BASE
> >+#define OMAP1_MPUIO_BASE 0xfffb5000
> >+
> >+#if (defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850))
> >+#define OMAP_MPUIO_INPUT_LATCH 0x00
> >+#define OMAP_MPUIO_OUTPUT 0x02
> >+#define OMAP_MPUIO_IO_CNTL 0x04
> >+#define OMAP_MPUIO_KBR_LATCH 0x08
> >+#define OMAP_MPUIO_KBC 0x0a
> >+#define OMAP_MPUIO_GPIO_EVENT_MODE 0x0c
> >+#define OMAP_MPUIO_GPIO_INT_EDGE 0x0e
> >+#define OMAP_MPUIO_KBD_INT 0x10
> >+#define OMAP_MPUIO_GPIO_INT 0x12
> >+#define OMAP_MPUIO_KBD_MASKIT 0x14
> >+#define OMAP_MPUIO_GPIO_MASKIT 0x16
> >+#define OMAP_MPUIO_GPIO_DEBOUNCING 0x18
> >+#define OMAP_MPUIO_LATCH 0x1a
> >+#else
> >+#define OMAP_MPUIO_INPUT_LATCH 0x00
> >+#define OMAP_MPUIO_OUTPUT 0x04
> >+#define OMAP_MPUIO_IO_CNTL 0x08
> >+#define OMAP_MPUIO_KBR_LATCH 0x10
> >+#define OMAP_MPUIO_KBC 0x14
> >+#define OMAP_MPUIO_GPIO_EVENT_MODE 0x18
> >+#define OMAP_MPUIO_GPIO_INT_EDGE 0x1c
> >+#define OMAP_MPUIO_KBD_INT 0x20
> >+#define OMAP_MPUIO_GPIO_INT 0x24
> >+#define OMAP_MPUIO_KBD_MASKIT 0x28
> >+#define OMAP_MPUIO_GPIO_MASKIT 0x2c
> >+#define OMAP_MPUIO_GPIO_DEBOUNCING 0x30
> >+#define OMAP_MPUIO_LATCH 0x34
> >+#endif
>
> Add prefixes to these defines and remove the ifdefs.
> This breaks multi-omap builds.
AFAIK multi-omap build not applicable for OMAP1
>
> >-struct gpio_bank {
> >- unsigned long pbase;
> >- void __iomem *base;
> >- u16 irq;
> >- u16 virtual_irq_start;
> >- int method;
> >-#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2PLUS)
> >- u32 suspend_wakeup;
> >- u32 saved_wakeup;
> >-#endif
> >-#ifdef CONFIG_ARCH_OMAP2PLUS
> >- u32 non_wakeup_gpios;
> >- u32 enabled_non_wakeup_gpios;
> >-
> >- u32 saved_datain;
> >- u32 saved_fallingdetect;
> >- u32 saved_risingdetect;
> >-#endif
> >- u32 level_mask;
> >- u32 toggle_mask;
> >- spinlock_t lock;
> >- struct gpio_chip chip;
> >- struct clk *dbck;
> >- u32 mod_usage;
> >-};
>
> defines are fine, but this structure belongs to this driver. Nobody else
> should need to poke on it. Keep it here.
This would get used in mach-omap layers in the later patches.
Hence moving it to gpio.h
>
> >@@ -625,10 +421,12 @@ void omap_set_gpio_debounce(int gpio, int enable)
> > bank = get_gpio_bank(gpio);
> > reg = bank->base;
> >
> >+#ifdef CONFIG_ARCH_OMAP2PLUS
> > if (cpu_is_omap44xx())
> > reg += OMAP4_GPIO_DEBOUNCENABLE;
> > else
> > reg += OMAP24XX_GPIO_DEBOUNCE_EN;
> >+#endif
>
> you should try to remove ifdefs not add more.
As mentioned in the beginning of this patch, these are
only temporary and all possible #ifdefs are removed at
the end of this patch series when plat-omap/gpio.c handles
only common APIs.
>
> --
> balbi
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
