> -----Original Message-----
> From: Felipe Balbi [mailto:[email protected]]
> Sent: Thursday, April 01, 2010 12:53 PM
> To: Varadarajan, Charulatha
> Cc: [email protected]; Nayak, Rajendra; [email protected];
> [email protected]
> Subject: Re: [PATCH 2/8] OMAP3:GPIO:Add support for early platform gpio device
>
> On Wed, Mar 31, 2010 at 02:23:53PM +0200, ext Charulatha V wrote:
> >This patch adds support for implementing OMAP3 GPIO as an
> >early platform device and adds gpio_init specific to OMAP3
> >
> >This patch adds device structures for each GPIO device in
> >OMAP3 architecture. These strutures are not created in a
> >separate *_data.c file because these structures would be
> >removed once the driver gets adapted to HWMOD way.
> >
> >Signed-off-by: Charulatha V <[email protected]>
> >---
> > arch/arm/mach-omap2/gpio3xxx.c | 351
> > +++++++++++++++++++++++++++++++
> > arch/arm/mach-omap2/include/mach/gpio.h | 13 +-
> > 2 files changed, 363 insertions(+), 1 deletions(-)
> > create mode 100644 arch/arm/mach-omap2/gpio3xxx.c
> >
> >diff --git a/arch/arm/mach-omap2/gpio3xxx.c b/arch/arm/mach-omap2/gpio3xxx.c
> >new file mode 100644
> >index 0000000..8f404e7
> >--- /dev/null
> >+++ b/arch/arm/mach-omap2/gpio3xxx.c
> >@@ -0,0 +1,351 @@
> >+/*
> >+ * gpio3xxx.c - OMAP3-specific gpio code
> >+ *
> >+ * Copyright (C) 2010 Texas Instruments, Inc.
> >+ *
> >+ * Author:
> >+ * Charulatha V <[email protected]>
> >+ *
> >+ * This program is free software; you can redistribute it and/or modify
> >+ * it under the terms of the GNU General Public License version 2 as
> >+ * published by the Free Software Foundation.
> >+ */
> >+
> >+#include <plat/gpio.h>
> >+
> >+/*
> >+ * OMAP3 GPIO reg offsets
> >+ */
> >+static struct gpio_reg_offset omap3_gpio_reg = {
> >+ .data_in = OMAP24XX_GPIO_DATAIN,
> >+ .data_out = OMAP24XX_GPIO_DATAOUT,
> >+ .data_out_set = OMAP24XX_GPIO_SETDATAOUT,
> >+ .data_out_clear = OMAP24XX_GPIO_CLEARDATAOUT,
> >+ .dir_ctrl = OMAP24XX_GPIO_OE,
> >+ .irq_status0 = OMAP24XX_GPIO_IRQSTATUS1,
> >+ .irq_status1 = OMAP24XX_GPIO_IRQSTATUS2,
> >+ .irq_mask = OMAP24XX_GPIO_IRQENABLE1,
> >+ .irq_set = OMAP24XX_GPIO_SETIRQENABLE1,
> >+ .irq_clear = OMAP24XX_GPIO_CLEARIRQENABLE1,
> >+ .irq_mask_bits = 0xffffffff,
> >+ .irq_inv = 0,
> >+ .wkup_enable = OMAP24XX_GPIO_WAKE_EN,
> >+ .wkup_clear = OMAP24XX_GPIO_CLEARWKUENA,
> >+ .wkup_set = OMAP24XX_GPIO_SETWKUENA,
> >+ .debounce_ena = OMAP24XX_GPIO_DEBOUNCE_EN,
> >+ .debounce_val = OMAP24XX_GPIO_DEBOUNCE_VAL,
> >+ .ctrl = OMAP24XX_GPIO_CTRL,
> >+ .syscfg = OMAP24XX_GPIO_SYSCONFIG,
> >+ .leveldetect0 = OMAP24XX_GPIO_LEVELDETECT0,
> >+ .leveldetect1 = OMAP24XX_GPIO_LEVELDETECT1,
> >+ .rise_detect = OMAP24XX_GPIO_RISINGDETECT,
> >+ .fall_detect = OMAP24XX_GPIO_FALLINGDETECT,
> >+ .rev_reg = OMAP24XX_GPIO_REVISION,
> >+};
> >+
> >+/*
> >+ * OMAP3 GPIO1 interface data
> >+ */
> >+static struct __initdata resource omap3_gpio1_resources[] = {
> >+ {
> >+ .start = OMAP34XX_GPIO1_BASE,
> >+ .end = OMAP34XX_GPIO1_BASE + OMAP3_GPIO_AS_LEN - 1,
>
> OMAP34XX_GPIO1_BASE + SZ_4K - 1
>
> >+ .flags = IORESOURCE_MEM,
> >+ },
> >+ {
> >+ .start = INT_34XX_GPIO_BANK1,
> >+ .flags = IORESOURCE_IRQ,
> >+ },
> >+};
> >+
> >+static struct __initdata omap_gpio_platform_data omap3_gpio1_config = {
> >+ .ick_name = "gpio1_ick",
> >+ .dbck_name = "gpio1_dbck",
>
> do not pass clock names. Update the clkdev entries clk*_data.c
Agreed. These patches are in preparation for HWMOD. Once GPIO driver gets
adapted to HWMOD, this would be removed.
>
> >+int __init omap3_early_init_gpio(struct platform_device ***pdev)
>
> I don't see the point in passing ***pdev.
It is required to get the early init device structure which is SoC specific.
>
> >+int __init omap3_gpio_dev_reg(void)
> >+{
> >+ if (cpu_is_omap34xx()) {
> >+ platform_device_register(&omap3_gpio1);
> >+ platform_device_register(&omap3_gpio2);
> >+ platform_device_register(&omap3_gpio3);
> >+ platform_device_register(&omap3_gpio4);
> >+ platform_device_register(&omap3_gpio5);
> >+ platform_device_register(&omap3_gpio6);
> >+ }
>
> platform_add_devices(omap3_gpio_early_dev,
> ARRAY_SIZE(omap3_gpio_early_dev);
>
> --
> balbi
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
